Alignment sets the angles at which the tyres meet the road. It affects tyre wear, straight-line stability and how a car turns in. It matters more on a car with more grip and a lowered suspension. This page covers the three main angles. The suspension setup that changes them is on coilover setup.
The three angles
Camber, caster and toe are the three primary alignment adjustments. Caster applies to the front wheels only, since the rear wheels are normally not steered, while camber and toe are adjustable at the front and rear. Some cars do not allow every angle to be adjusted at every wheel (Wikipedia: Wheel alignment). Caster mainly affects steering and tracking and is normally left to the vehicle maker's setting.
Camber
Camber is the angle between the wheel's vertical axis and the vehicle's vertical axis, seen from the front or rear. If the top of the wheel tilts outward it is positive camber, and if the bottom tilts outward it is negative (Wikipedia: Camber angle).
- Cornering. Negative camber can improve cornering grip, especially with short-and-long-arm suspensions, by keeping the outside tyre's contact patch flatter against the road under load. Weight transfer loads the outside wheels more in a turn, so some negative camber generally helps, and it can offset the positive camber that body roll induces on the outside tyre.
- Straight-line grip. Zero camber gives the best traction in straight-line driving and hard acceleration, because the tread sits flat on the road.
- Wear. Excessive camber of either sign causes uneven wear. Excess negative camber loads the inner shoulder, and positive camber loads the outer shoulder.
More negative camber is not automatically better. It trades straight-line grip and even wear for cornering grip, and the right amount depends on the suspension geometry, the tyres and the use.
Toe
Toe is the angle each wheel makes with the car's centreline. Toe-in (positive toe) points the front of the wheel toward the centreline, and toe-out points it away (Wikipedia: Toe (automotive)).
- Tyre wear. Increased front toe-in marginally increases wear, because the tyres run with slight side slip when the steering is straight ahead. A small amount of toe offsets the tyre's tendency to roll in a curve when camber is present: toe-out suits negative camber and toe-in suits positive camber.
- Stability against response. On a rear-drive car, more front toe-in gives more straight-line stability at the cost of slower turning response. Performance cars may run zero front toe or some toe-out for sharper response to steering. Rear toe-in is described as giving better stability in cornering.
- Units. Toe can be given as an angle or as a distance at axle height. An angle does not depend on tyre size, but a distance does.
Lowering changes the angles
Shortened springs change camber, and some suspension layouts tilt the wheels inward when lowered. MacPherson strut suspensions usually have fixed camber, while double-wishbone designs may allow adjustment with camber plates, eccentric bolts or adjustable control arms (Wikipedia). So a lowered or re-sprung car needs its alignment checked and, where possible, corrected after the change. Extreme camber and very low ground clearance for appearance can make a car impractical.
Setting alignment
- Record the manufacturer's alignment specification and the current angles before any suspension change.
- After lowering, new springs or coilovers, set the ride height first, let the suspension settle, and then align.
- Align to the maker's specification for a road car. Angles may be set outside it for competition or off-road use for particular handling, and vehicle inspections may require angles to stay within the maker's tolerance, so check the requirements in your area.
- Change one angle at a time and record the effect on feel and on tyre wear, with the same tyres and pressures: tyre pressures for performance driving.
- Check the tyres' wear pattern after a few hundred kilometres, and again after hard use.
The Wikipedia articles on these angles are tagged as needing more citations, and they give no recommended angle values, so this page does not either. Use the vehicle maker's figures and a competent alignment specialist. See also anti-roll bars and handling balance and wheel size, offset and unsprung mass.
Sources
- Wheel alignment. Wikipedia. The three adjustments, where they apply, and motorsport and inspection notes. Flagged as needing more citations. Accessed 2026-11-19.
- Camber angle. Wikipedia. Definition, cornering, wear and lowering. Some sections flagged as lacking citations. Accessed 2026-11-19.
- Toe (automotive). Wikipedia. Definition, wear, stability and response. Flagged as needing more citations. Accessed 2026-11-19.