Page organisation in this revision
- Page type
- Technical article
- Subject
- Performance
- Parent
- Section level
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 1 to revision 1
Removed text is struck through; added text is highlighted.
At road speeds above a few tens of kilometres per hour, most of the power an engine delivers goes into pushing air out of the way. That sets how much extra power is needed for a given gain in top speed, and why aerodynamic add-ons are a trade-off. This page gives the relationship and a worked example. For traction limits at low speed see power, weight and traction, and for how speed relates to engine rpm see gearing, final drive and road speed.
The drag force
The drag force on a car is F = ½ × air density × drag coefficient × frontal area × speed², with speed in metres per second. The product of drag coefficient (Cd) and frontal area is the drag area, CdA (Wikipedia: Automobile drag coefficient).
Drag coefficient (Cd) is a unitless number for how much the body shape resists movement through the air. It depends on shape, and the same car can measure up to about 5 per cent differently in different wind tunnels. An average modern car sits around 0.25 to 0.30, and SUVs around 0.35 to 0.45.
Frontal area is the other main factor. A smaller frontal area lowers drag. The average full-size car's drag area is about 0.74 m².
Air density falls with temperature and altitude, which lowers drag and also lowers engine power at the same time.
Power rises with the cube of speed
Force rises with the square of speed and power is force times speed, so the power needed to overcome drag rises with the cube of speed. In round terms, doubling the speed needs eight times the power for drag. The same source gives the working rules: an estimated new top speed is the original top speed multiplied by the cube root of the ratio of the new power to the original, and the power needed for a target speed is the original power multiplied by the cube of the ratio of the speeds. Rolling resistance and drivetrain losses come on top, so these rules are approximations that work best at high speed.
Worked example
This is an illustrative calculation, not data for any car. Take a drag coefficient of 0.30, a frontal area of 2.2 m² (a drag area of 0.66 m²) and an air density of 1.2 kg/m³.
SpeedDrag forcePower to overcome drag
100 km/h (27.8 m/s)305 Nabout 8.5 kW (11 hp)
200 km/h (55.6 m/s)1,222 Nabout 68 kW (91 hp)
Doubling the speed multiplied the drag power by eight. A 20 per cent increase in power would raise the high-speed limit by only about 6 per cent (the cube root of 1.2 is about 1.063), which is why large power gains buy modest top-speed gains. Reducing the drag area by a given percentage has the same effect as raising power by that percentage, at the speeds where drag dominates.
Downforce costs drag
Downforce creates drag, so many sports cars have relatively high drag coefficients, while other cars are designed for low drag and efficiency. Altering the aerodynamics can also add lift, which can reduce traction. An aerodynamic part fitted without measurement can raise drag, change the balance between the axles and make the car less stable at speed, so fit parts designed and tested for the car, and check the balance front to rear.
Downforce matters most where grip, not power, limits the car: in fast corners, and under braking from high speed. It has little effect at the low speeds where traction is limited by the tyres, so do not expect an aerodynamic part to change a launch: power, weight and traction.
Planning with it
Decide whether the limit is acceleration, top speed or cornering. Aerodynamics matters for the second and third, power and traction for the first.
Use the cube relationship to check whether a power target is realistic for a top-speed target before spending on the engine: planning a performance engine build.
Remember that higher speeds also load the cooling system, the tyres and the brakes: engine cooling, tyre pressures and brake pads.
Measure the result with a repeatable test, not an estimate, and note the temperature and the wind.
Sources
Automobile drag coefficient. Wikipedia. Drag formula, typical coefficients, drag area, power and speed relationships and the downforce trade-off. Accessed 2026-11-19.
The worked example is arithmetic with illustrative values using the formula above.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Aerodynamic drag, downforce and the power needed for speed
At road speeds above a few tens of kilometres per hour, most of the power an engine delivers goes into pushing air out of the way. That sets how much extra power is needed for a given gain in top speed, and why aerodynamic add-ons are a trade-off. This page gives the relationship and a worked example. For traction limits at low speed see power, weight and traction, and for how speed relates to engine rpm see gearing, final drive and road speed.
The drag force
The drag force on a car is F = ½ × air density × drag coefficient × frontal area × speed², with speed in metres per second. The product of drag coefficient (Cd) and frontal area is the drag area, CdA (Wikipedia: Automobile drag coefficient).
- Drag coefficient (Cd) is a unitless number for how much the body shape resists movement through the air. It depends on shape, and the same car can measure up to about 5 per cent differently in different wind tunnels. An average modern car sits around 0.25 to 0.30, and SUVs around 0.35 to 0.45.
- Frontal area is the other main factor. A smaller frontal area lowers drag. The average full-size car's drag area is about 0.74 m².
- Air density falls with temperature and altitude, which lowers drag and also lowers engine power at the same time.
Power rises with the cube of speed
Force rises with the square of speed and power is force times speed, so the power needed to overcome drag rises with the cube of speed. In round terms, doubling the speed needs eight times the power for drag. The same source gives the working rules: an estimated new top speed is the original top speed multiplied by the cube root of the ratio of the new power to the original, and the power needed for a target speed is the original power multiplied by the cube of the ratio of the speeds. Rolling resistance and drivetrain losses come on top, so these rules are approximations that work best at high speed.
Worked example
This is an illustrative calculation, not data for any car. Take a drag coefficient of 0.30, a frontal area of 2.2 m² (a drag area of 0.66 m²) and an air density of 1.2 kg/m³.
| Speed | Drag force | Power to overcome drag |
| 100 km/h (27.8 m/s) | 305 N | about 8.5 kW (11 hp) |
| 200 km/h (55.6 m/s) | 1,222 N | about 68 kW (91 hp) |
Doubling the speed multiplied the drag power by eight. A 20 per cent increase in power would raise the high-speed limit by only about 6 per cent (the cube root of 1.2 is about 1.063), which is why large power gains buy modest top-speed gains. Reducing the drag area by a given percentage has the same effect as raising power by that percentage, at the speeds where drag dominates.
Downforce costs drag
Downforce creates drag, so many sports cars have relatively high drag coefficients, while other cars are designed for low drag and efficiency. Altering the aerodynamics can also add lift, which can reduce traction. An aerodynamic part fitted without measurement can raise drag, change the balance between the axles and make the car less stable at speed, so fit parts designed and tested for the car, and check the balance front to rear.
Downforce matters most where grip, not power, limits the car: in fast corners, and under braking from high speed. It has little effect at the low speeds where traction is limited by the tyres, so do not expect an aerodynamic part to change a launch: power, weight and traction.
Planning with it
- Decide whether the limit is acceleration, top speed or cornering. Aerodynamics matters for the second and third, power and traction for the first.
- Use the cube relationship to check whether a power target is realistic for a top-speed target before spending on the engine: planning a performance engine build.
- Remember that higher speeds also load the cooling system, the tyres and the brakes: engine cooling, tyre pressures and brake pads.
- Measure the result with a repeatable test, not an estimate, and note the temperature and the wind.
Sources
- Automobile drag coefficient. Wikipedia. Drag formula, typical coefficients, drag area, power and speed relationships and the downforce trade-off. Accessed 2026-11-19.
- The worked example is arithmetic with illustrative values using the formula above.
Revision 1: Aerodynamic drag, downforce and the power needed for speed
At road speeds above a few tens of kilometres per hour, most of the power an engine delivers goes into pushing air out of the way. That sets how much extra power is needed for a given gain in top speed, and why aerodynamic add-ons are a trade-off. This page gives the relationship and a worked example. For traction limits at low speed see power, weight and traction, and for how speed relates to engine rpm see gearing, final drive and road speed.
The drag force
The drag force on a car is F = ½ × air density × drag coefficient × frontal area × speed², with speed in metres per second. The product of drag coefficient (Cd) and frontal area is the drag area, CdA (Wikipedia: Automobile drag coefficient).
- Drag coefficient (Cd) is a unitless number for how much the body shape resists movement through the air. It depends on shape, and the same car can measure up to about 5 per cent differently in different wind tunnels. An average modern car sits around 0.25 to 0.30, and SUVs around 0.35 to 0.45.
- Frontal area is the other main factor. A smaller frontal area lowers drag. The average full-size car's drag area is about 0.74 m².
- Air density falls with temperature and altitude, which lowers drag and also lowers engine power at the same time.
Power rises with the cube of speed
Force rises with the square of speed and power is force times speed, so the power needed to overcome drag rises with the cube of speed. In round terms, doubling the speed needs eight times the power for drag. The same source gives the working rules: an estimated new top speed is the original top speed multiplied by the cube root of the ratio of the new power to the original, and the power needed for a target speed is the original power multiplied by the cube of the ratio of the speeds. Rolling resistance and drivetrain losses come on top, so these rules are approximations that work best at high speed.
Worked example
This is an illustrative calculation, not data for any car. Take a drag coefficient of 0.30, a frontal area of 2.2 m² (a drag area of 0.66 m²) and an air density of 1.2 kg/m³.
| Speed | Drag force | Power to overcome drag |
| 100 km/h (27.8 m/s) | 305 N | about 8.5 kW (11 hp) |
| 200 km/h (55.6 m/s) | 1,222 N | about 68 kW (91 hp) |
Doubling the speed multiplied the drag power by eight. A 20 per cent increase in power would raise the high-speed limit by only about 6 per cent (the cube root of 1.2 is about 1.063), which is why large power gains buy modest top-speed gains. Reducing the drag area by a given percentage has the same effect as raising power by that percentage, at the speeds where drag dominates.
Downforce costs drag
Downforce creates drag, so many sports cars have relatively high drag coefficients, while other cars are designed for low drag and efficiency. Altering the aerodynamics can also add lift, which can reduce traction. An aerodynamic part fitted without measurement can raise drag, change the balance between the axles and make the car less stable at speed, so fit parts designed and tested for the car, and check the balance front to rear.
Downforce matters most where grip, not power, limits the car: in fast corners, and under braking from high speed. It has little effect at the low speeds where traction is limited by the tyres, so do not expect an aerodynamic part to change a launch: power, weight and traction.
Planning with it
- Decide whether the limit is acceleration, top speed or cornering. Aerodynamics matters for the second and third, power and traction for the first.
- Use the cube relationship to check whether a power target is realistic for a top-speed target before spending on the engine: planning a performance engine build.
- Remember that higher speeds also load the cooling system, the tyres and the brakes: engine cooling, tyre pressures and brake pads.
- Measure the result with a repeatable test, not an estimate, and note the temperature and the wind.
Sources
- Automobile drag coefficient. Wikipedia. Drag formula, typical coefficients, drag area, power and speed relationships and the downforce trade-off. Accessed 2026-11-19.
- The worked example is arithmetic with illustrative values using the formula above.