Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Turbocharging
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

A turbocharger is chosen by matching its compressor to the air the engine needs. The tool for that is the compressor map. This page explains what the map shows, how to estimate the engine's airflow, and how to check the two against each other. Turbocharger upgrades and modifications compares turbo types and examples, and turbocharging overview covers how a turbo works.

What a compressor map shows

A compressor map plots the compressor's behaviour on two axes (Wikipedia: Compressor map):

  • Horizontal axis: compressor inlet mass flow, normally corrected to standard conditions so that maps can be compared.
  • Vertical axis: total pressure ratio, the outlet pressure divided by the inlet pressure.
  • Speed lines: near-vertical, slightly curved lines of constant corrected shaft speed. Beyond choke they close up rapidly.
  • Surge line: the low-flow boundary, where the blades stall. Operation beyond it is unstable and should be avoided.
  • Choke: the high-flow boundary, where the gas in the passages reaches the speed of sound. Past it, extra speed adds no airflow.
  • Efficiency: shown as contours or a sub-plot. The compressor does the least wasted work, and so heats the air least, in the region of peak efficiency.

Corrected flow adjusts measured flow to reference conditions. The usual form multiplies the mass flow by the square root of the inlet temperature ratio and divides by the inlet pressure ratio, against the sea-level standard day. Check which reference temperature and pressure a given map uses, and which flow units, since makers differ.

Estimating the engine's airflow

For a four-stroke engine, the air mass flow is the volume swept per second, multiplied by the volumetric efficiency and the density of the air in the manifold:

Mass flow = displacement × (rpm ÷ 120) × volumetric efficiency × manifold air density

Density is pressure divided by (287 × absolute temperature in kelvin), with pressure in pascals. The volumetric efficiency of a boosted engine is typically a little lower than one, and the correct figure for an engine comes from measurement, not from a table. The pressure ratio needed is the absolute manifold pressure divided by the ambient pressure, plus the pressure lost in the intake, intercooler and pipework, which raises the ratio the compressor itself must make.

Worked example

This is an illustrative calculation, not a recommendation for any engine. Take a 2.0-litre four-cylinder at 6,000 rpm, a volumetric efficiency of 0.90, and manifold conditions of 202.65 kPa absolute (about 1.0 bar of boost) at 300 K.

StepValue
Manifold air density, 202,650 ÷ (287 × 300)2.35 kg/m³
Volume of air drawn in per second, 0.002 m³ × 6,000 ÷ 1200.100 m³/s
Mass flow, 0.100 × 0.90 × 2.350.212 kg/s, about 28 lb/min
Pressure ratio before losses, 202.65 ÷ 101.3about 2.0

So the compressor would need to deliver about 0.21 kg/s at a pressure ratio a little above 2.0, once the pressure drops in the intake and intercooler are added. That point is then plotted on the map, after converting to the map's corrected flow and units.

Checking the match

  1. Calculate the flow and pressure ratio at the engine speeds that matter: the torque peak, the power peak and the speed where boost must be fully up. Plot each point on the map.
  2. Check that the points sit away from the surge line. The full-load operating line runs close to surge at low engine speed, so low-speed points need a margin.
  3. Check that the high-speed points stay short of choke, and that corrected speed is within the compressor's limits.
  4. Check that the operating points fall in or near a high-efficiency region, because poor efficiency means a hotter charge and less density for the same boost: charge cooling.
  5. Match the turbine side too. A large compressor with a small turbine cannot be driven, and a large turbine builds boost late. The exhaust housing, wastegate and engine's exhaust flow are part of the same decision: exhaust system tuning.

Wastegate control and altitude shift the operating line on the map. At altitude the ambient pressure falls, so the same manifold pressure needs a higher pressure ratio: see Simos 18 altitude and ambient pressure effects and MED17.5.21 altitude and boost-request diagnosis. Compressor surge protection in a factory calibration is covered on Simos 18 turbocharger protection.

What a map does not tell you

  • Response. A map shows steady-state behaviour. How quickly a turbo spools depends on the turbine, rotor inertia and the exhaust energy available, which a compressor map does not show.
  • Your engine's real airflow. The volumetric efficiency used above is an estimate. Measure with a mass airflow meter or logged manifold pressure where possible.
  • The supporting parts. More airflow needs more fuel, a stronger engine and a calibration: fuel system upgrades, pistons and rods and electronic boost control.

Sources

  • Compressor map. Wikipedia. Axes, speed lines, surge, choke, efficiency, corrected flow and matching. Accessed 2026-11-19.
  • The airflow relation and the worked example are standard relations (swept volume per second, volumetric efficiency and the ideal gas law) applied with illustrative values. See also MIT OpenCourseWare 2.61 lecture 8 for volumetric efficiency. Accessed 2026-11-11.