Scope. Ambient pressure affects pressure references and some ECU calculations. The identifiers below come from the community SC8S5031_C_OEM Simos 18.1 cross-reference and describe that software image; they are not universal altitude maps. Verify the ECU, turbo, sensor configuration, units, axis sources and active logic. Extracted descriptions can be incomplete or inconsistent. INSY air-pressure reference; CHRG pressure-setpoint application reference.
Ambient pressure and compressor pressure ratio
At a higher elevation ambient pressure is often lower, although weather also affects it. A gauge boost reading is pressure relative to local ambient; absolute pressure includes ambient. Compressor pressure ratio uses absolute compressor-outlet pressure divided by absolute compressor-inlet pressure. Inlet restriction can make inlet pressure lower than ambient, and pressure losses mean manifold pressure or pressure upstream of the throttle is not necessarily compressor-outlet pressure. Garrett compressor pressure-ratio explanation.
For an idealised illustration only, assume no pressure drop at either end: at 1,000 mbar ambient and 1,000 mbar gauge outlet pressure the ratio is 2.00; at 800 mbar ambient with the same gauge outlet pressure it is 2.25. Actual inlet restriction and charge-pipe/intercooler losses change the result. Keeping the same gauge boost across altitudes can therefore demand a different compressor operating point. A calculated ratio alone does not establish safe turbo speed, compressor efficiency or power.
Ambient-pressure signal and sensor conversion
In the SC8S5031 INSY definitions, amp is an ambient-pressure quantity. ip_amp_mes is a voltage-to-pressure conversion characteristic for an analogue ambient-pressure path, with vp_amp in volts and an hPa output. ip_amp_iaps_bas is a separate conversion from a digital ambient-pressure sensor input in this reference. Which path and sensor are fitted and active depends on configuration. Do not confuse either curve with manifold MAP or upstream-throttle PUT sensor conversion.
ECU pressure equalisation, filtering and fault substitution can affect the final signal; check the target definitions and sensor status. A key-on engine-off comparison with a reliable local station-pressure reference can reveal a gross discrepancy once values settle, but a single reading does not validate an entire transfer function. Use station pressure, not a weather report corrected to sea level, and verify sensor and wiring before changing any conversion.
Example ambient-dependent calibration and protection
ip_fac_bpa_sp_amp_ofsis described as an ambient-pressure correction of the boost-pressure-actuator position setpoint, withampin hPa andflow_wg_spin kg/h as axes.ip_fac_amp_posn_sp_bpa_rglis another ambient-related actuator-position correction in the same reference. These are actuator-control contributions, not a simple boost target. CHRG turbine control.ip_put_sp_optm_resp_basgives a basic PUT setpoint for a best-response operating mode against ambient pressure; it is not necessarily the final setpoint or active in every mode.c_fac_put_sp_bol_ampscales a lower PUT setpoint limit relative to ambient. CHRG application reference.ip_pq_cha_maxis a maximum compressor-pressure-ratio map against engine speed and upstream-compressor air temperature, not an altitude-versus-boost map. The same reference describesc_pq_cha_max_ofs_ampas an offset used when the ambient-pressure sensor is not enabled. Verify fault-state selection and signs in the matched software.c_amp_min_cap_l_diagis a minimum ambient-pressure condition for the low charge-pressure diagnostic, according to the turbocharger control plausibility reference. It is a diagnostic enable condition, not a desired operating pressure.put_max_tcha_protis a runtime coordinated maximum upstream-throttle pressure associated with turbo limits, not an editable pressure-target map. The reference describes multiple limit paths; their actual activation and correspondence to a particular turbo must be checked. CHRG protection-related signal description.
Comparison and validation
- Record software and tune, actual turbo hardware, altitude or local station pressure, ambient and intake temperature, fuel, gear and operating conditions for each log. Establish pressure sensor location, units and absolute versus gauge reference.
- Log ambient pressure, manifold and PUT pressures and their relevant setpoints, air charge, wastegate request and position where available, and turbo protection states. Compare equivalent conditions while recognising that available power and target limits can differ. The COBB MQB monitor list is an example of tool-specific channel definitions, not a guarantee for every ECU.
- For compressor-map work, measure or defensibly estimate pressure at the actual compressor inlet and outlet, account for inlet restriction and charge-cooler pressure drop, and use the correct compressor map, corrected flow and validated speed or temperature evidence. Manifold gauge boost alone cannot locate the operating point reliably.
- Do not suppress ambient-sensor or boost diagnostics, or remove compressor temperature, speed and surge protections to force a sea-level result. A replacement turbo can make the factory model inaccurate; identify the hardware and validate its limits rather than treating a familiar calibration name as a transferable safe value.
Related: MAP and boost pressure sensors · turbocharger protection · wastegate and boost control · bigger turbo tuning.
Sources
- Garrett: compressor pressure ratio and inlet depression, general turbocharging principles.
- SC8S5031 community air-pressure acquisition, turbine control and pressure-setpoint application; image-specific definitions.
- CHRG turbo plausibility diagnosis and boost pressure display and coordinated limits.
- COBB VW/Audi MQB monitor descriptions, product- and application-specific.