Tuners sell upgrades in "stages", but there is no standard definition. 8020 Automotive says the meaning of stages "can vary from car to car and engine to engine", with some brands using 1, 1+ and 2, others 1 to 3, and some going to 5. This page describes the common pattern and the questions to ask before buying a package. Gain figures here are one retailer's ranges, not results for any given car.
The common pattern
- Stage 1. A calibration change for an essentially standard car. 8020 Automotive lists about 5 to 20 hp for naturally aspirated engines and often 20 to 50 or more for turbocharged ones, and notes the usual supporting parts as an intake, cat-back exhaust or blow-off valve. CSC Motors, a UK remapper, says Stage 1 assumes a healthy, well-maintained, standard vehicle and allows only very minor changes such as a filter that does not significantly alter airflow.
- Stage 2. A calibration matched to bolt-on hardware that helps the engine breathe. CSC gives an upgraded intake and a performance exhaust as examples. 8020 adds headers on a naturally aspirated engine or downpipes on a turbo engine, and an uprated front intercooler as a common cooling upgrade. Its "Stage 2+" may need camshafts or pulleys and a higher octane or ethanol fuel.
- Stage 3 and above. Major hardware: a larger turbo or supercharger, extensive fuel system upgrades and often strengthened internals. 8020 lists rods, pistons, bearings and head studs, plus brakes, suspension, differential, tyres and cooling. CSC says Stage 3 is often suited to track use.
The two sources agree on the shape and differ on detail, which is the point: check what a specific tuner's package contains and what parts it assumes.
What changes as the stage rises
The common thread is that every added unit of output adds a demand elsewhere. In this wiki's pages the demands map out like this:
- Air. Air filters, intake ducting and restriction, exhaust system tuning and charge cooling.
- Fuel. Fuel system upgrades, fuel pumps, regulators and lines and E85 and flex fuel.
- Calibration and measurement. ECU remapping, boost control, ignition timing, lambda and data logging.
- Survival. Pistons and rods, head gaskets and studs, cooling and oil.
- Getting the power down. Power, weight and traction, the clutch and the gearbox.
Generic and bespoke tunes
CSC Motors distinguishes a generic tune, a pre-made file for a range of vehicles of the same make, model and engine, from a bespoke tune. A generic file does not account for the car's condition, mileage, modifications or the fuel quality and altitude it will see. A bespoke tune, in CSC's description, involves reading the ECU, a diagnostic health check, data logging, tailored calibration and dyno testing. A higher stage on a generic file leaves more of the risk with the owner. See how an ECU is remapped and common misconceptions about remapping.
Questions to ask before buying
- What exactly is included in this stage, and which parts must already be fitted? Which supporting parts are assumed but not sold?
- Is the file generic or built for this car, and is it checked on a dyno or a road log?
- What does the package assume about fuel, and what happens if the car is run on a lower grade?
- What condition checks come first: compression, leaks, boost, fuel pressure, codes?
- Which parts of the car limit at this level: clutch, tyres, cooling, brakes?
- Is the package legal for the intended use? CSC says its DPF option applies only where legal for off-road or motorsport use. Emissions equipment, insurance, warranty and roadworthiness rules vary by country, and none of the sources above covers them, so ask the tuner and your insurer and check local law.
All engine modification and tuning is at the owner's risk. 8020 says more power adds stress the engine may or may not tolerate, and that a tuner's own recommendations should be followed over a generic parts list. Agree what will be measured and reported before the work starts, as set out under agreeing the work with a tuning provider on engine performance upgrades.
Sources
- Tuning Stages - Stage 1, 2, 3, Tunes. 8020 Automotive, 15 October 2021 (updated 22 January 2024). Stage ranges, typical mods and the variability of definitions. Retailer figures. Accessed 2026-11-19.
- Explaining Stage 1, Stage 2, and Stage 3 remapping. Craig Burns, CSC Motors, 13 June 2025. Stage prerequisites and generic against bespoke tunes. Accessed 2026-11-19.