Scope. The calibration identifiers below are examples from the community SC8S5031_C_OEM Simos 18.1 cross-reference. Identify the exact ECU software, sensor configuration, operating conditions, map units, axes and active path before using any definition. Extracted text sometimes conflicts with field labels, and addresses and table values do not automatically transfer between images.
Engine-out, turbine and catalyst temperatures
Exhaust temperature depends on engine load, speed, air and fuel mixture, ignition and the exhaust path. The SC8S5031 EXTD reference describes an engine-out model and component models; it also describes a possible sensor input for configured positions, with a model value when a sensor is absent, disabled or faulty. This is a software example, not proof that a particular vehicle has an EGT sensor or that every diagnostic value is measured.
Different locations and operating histories produce different values: engine-out or upstream-turbine exhaust gas temperature is not the catalyst substrate temperature. A steady-state estimate and a transient/dynamic estimate are also different model outputs. In the COBB MQB monitor list, EGT Upstream Turbo is explicitly a modelled manifold exhaust temperature for its listed vehicles. Its Catalyst Temperature label alone does not establish a physical probe location. Confirm what each tool displays.
SC8S5031 engine-out model examples
The following entries are from the engine-out EGT model reference. They describe model data, not requested ignition, lambda or proven safe temperature limits:
ip_teg_eng_out_bas: basic engine-out temperature at reference conditions in °C. The axis metadata gives engine speedn_tegin rpm and an mg/stroke axisldpm_maf_cbk_teg_1_extd, whose input is listed asonline_dummy; confirm the actual runtime signal. The copied functional-description table line is inconsistent with the title.ip_teg_add_iga: additive engine-out temperature correction in K, with an ignition-angle-difference axis in crank degrees; the axis runtime input is not established by itsonline_dummylabel.ip_fac_teg_add_igasupplies an operating-point weighting factor; verify its selection and active path.ip_teg_add_lamb: additive temperature correction in K on a lambda-related axis;ip_fac_teg_add_lambis a weighting factor. The output is a temperature-model correction, not an air-fuel target.ip_fac_teg_tcois a warm-up factor against coolant and start coolant temperatures;ip_fac_teg_tiais an intake-temperature-related factor. Confirm the target image and channels.ip_iga_bas_teg,ip_iga_ref_tegandip_lamb_bas_tegare reference quantities for the model, not necessarily the commanded spark or mixture. The associated RPM and mg/stroke axis metadata has the same uncertain runtime-input label.
Sensor selection and validation
lc_teg_mdl_sens_ena[0] is described as a sensor-information enable for the exhaust-temperature model, while extd_struct_mdlad0[7].teg_dyn_mdl is a dynamic model-temperature measurement array. Array sizes, positions and sensor selection require the matching definition and actual hardware. The EXTD output-selection reference also identifies temp_cat_stat_mdl_ohp[0] as a steady-state catalyst model output used for overheating prevention.
- Record exact hardware, software, exhaust and turbine configuration, fuel, sensor positions and whether each channel is measured, calculated or substituted. Establish an unmodified healthy baseline and record relevant fault codes.
- Where a suitable independent temperature measurement is available, compare it with the model only at a known, comparable location and operating state. Consider probe response, installation, heat soak and dynamic lag; a single probe cannot validate every component model.
- Log EGT channel, lambda request and actual, ignition, speed, load, relevant temperature and intervention state when supported. Compare matching conditions, including duration at load. COBB's monitor list provides examples but channel availability depends on product and vehicle.
- Hardware or calibration changes can change heat flow and model accuracy. Investigate sensor faults, fuel and air delivery and actual component temperature before attributing protective intervention to a calibration. Preserve exhaust-component protections.
Related: catalyst overheating protection · turbocharger protection · lambda control · tuning and log diagnosis.
For turbine and catalyst pressure locations, model names and restriction checks, see Simos 18 exhaust pressure modelling and restriction diagnosis.