Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

Scope. This guide concerns the cam-driven high-pressure fuel pump (HPFP) on EA888 applications using Simos 18. Pump type, cam drive, software, injection hardware and supporting low-pressure supply vary. The named ECU fields are examples from the community SC8S5031_C_OEM Simos 18.1 reference; verify the exact software, definition, units, selectors and hardware before applying them. Representable values are not recommended settings.

Displacement, pressure and capacity

The low-pressure system supplies fuel to the mechanically driven HPFP, which delivers fuel to the direct-injection rail. A volume-control valve (VCV) participates in pressure control. A larger pump or internal plunger can increase potential delivery per pump stroke; that does not automatically increase the commanded rail-pressure target or solve an inadequate low-pressure feed. APR explicitly describes its EA888 Gen 3 HPFP upgrade as increasing displacement rather than necessarily raising rail pressure. The product description is an example, not evidence of a universal power limit or fitment.

The physical pump, cam profile and follower must match the installation. For its specified EA888.3 1.8T Stage 3 package, Unitronic lists a 2.0T pump together with a different follower and vacuum-pump assembly. That requirement belongs to its stated application and does not establish interchangeability for other engines. Verify component part numbers and the tuner’s calibration requirements for the actual vehicle.

Example SC8S5031 pump model and actuator names

In the FUSL fuel-pressure actuator reference:

  • c_mfp_max is described as maximum pump-delivered fuel mass per pump stroke, in mg. The source says operating-dependent factors influence the calculated maximum; the calibration value is a model input, not a bench measurement of the installed pump or a pressure target.
  • ip_fac_fuel_pump_eff_fup_n is an efficiency factor against engine speed n_32 and fuel-pressure input fup in hPa. The narrative calls the pressure a setpoint while the axis metadata names fup; verify the actual signal. ip_fac_fuel_pump_eff_mff_sp_n is a factor against engine speed and fuel-mass-flow setpoint, and ip_fac_fuel_pump_eff_tfu_n uses engine speed and HPFP fuel temperature tfu_hpp. These are model factors, not measured pump efficiencies.
  • ip_mfp_ofs is a fuel-mass offset for internal pump behaviour, in mg against speed and fuel pressure. The description associates it with dead volume in the documented model. Do not assume the same offset or factor characterises a different pump.
  • ip_vcv_close_rng converts required pump-volume input pump_vol_vcv in percent to a VCV closing angle in crank degrees. It is a control conversion, not the rail-pressure target or injector SOI map. Correct interpretation depends on pump and valve type, phasing and software.

mfp_req, mfp_max, mfp_ofs, pump_vol_vcv and cam_fuel_pump are runtime model or control quantities in that reference, not editable pump specifications. The separate fuel-pressure-control reference describes c_pump_vol_vcv_max and c_pump_vol_vcv_min as effective-pump-volume conditions for stopping the high-pressure controller. They are control conditions, not a universal safe-flow ceiling.

Rail-pressure feedback and fuel-mass adaptation

The SC8S5031 FUSL pressure-control reference identifies ip_fuel_mass_req_p_ctl and ip_fuel_mass_req_i_ctl as proportional and integral fuel-mass request curves respectively. Their axis is the pressure deviation fup_dif in hPa and their output is in mg. The exact sign convention and installed software must be verified before interpreting a curve. ip_fac_fuel_mass_i_ctl_n and ip_fac_fuel_mass_p_ctl_n are speed-dependent factors; the latter's descriptive text calls it a P factor but a copied table caption says I, so confirm it in the target definition. ip_fac_fuel_mass_p_ctl_tfu describes a temperature-dependent P factor using tfu_hpp; COBB describes its similarly named HPFP fuel-temperature monitor as modelled rather than necessarily sensor-measured.

The same reference describes a separate learned fuel-mass correction: c_fuel_mass_ad_cor_crlc is its filter constant, c_fuel_mass_ad_min and c_fuel_mass_ad_max are its mg limits, and c_fup_dif_min_fuel_mass_ad_stop is a pressure-deviation condition for stopping adaptation. c_n_fuel_mass_ad_min/max and c_mfp_fuel_mass_ad_min/max describe speed and pump-mass conditions. Runtime flags lv_fuel_mass_ad_ena, lv_fuel_mass_ad_stop and lv_fuel_mass_ctl_stop describe adaptation enable, adaptation stop and I-part freeze respectively; they are not editable maps. This correction is distinct from lambda fuel trims and pressure-sensor offset adaptation. Check whether the relevant learning and controller states are active when comparing otherwise similar logs; these names do not imply universal tuning values.

VCV holding and soft-landing adaptation

In the SC8S5031 actuator reference, ip_pwm_vcv_ctl_2_bas is described as base VCV holding-phase duty against battery voltage vb and actuator resistance r_vcv, although its copied caption says pick-up phase. ip_pwm_vcv_ctl_sl_ad_end describes an adapted-duty correction against voltage and resistance; ip_t_dur_vcv_ctl_sl_ad_end describes a pull-in-time correction after soft-landing adaptation, though its copied caption calls it a base time. The narrative refers to actuator temperature while the published axes use resistance: do not assume a direct coil-temperature sensor or resolve the caption conflicts without the target definition.

lv_vcv_close_sl_ad_req and lv_vcv_close_sl_ad_end are runtime request and completion flags, while pwm_vcv_close_sl_ad and ctr_vcv_close_sl_ad describe adapted holding duty and an adaptation counter. c_vb_dif_max_vcv_close_sl_req and c_r_dif_max_vcv_close_sl_req are voltage and resistance conditions for requesting readaptation. Their presence and meaning must be checked for the actual software and actuator; completion alone does not prove that rail-pressure tracking or pump flow is correct.

Diagnosis after a hardware change

  1. Record the exact ECU calibration, pump and internals, follower/cam hardware, low-side system, injector setup, fuel and faults. Use the pump and software supplier's instructions; EcuTek describes fuel-pump calibration for compatible pump designs in its EA888 tuning overview.
  2. Compare high-pressure rail target and actual with low-side pressure and target, fuel temperature, injection duration, combustion mode, lambda target/actual and fuel trims over relevant operating conditions. COBB calls HPFP Effective Pump Volume a modelled quantity and lists HPFP controller and feedback channels for supported applications. A high value may be a useful diagnostic lead, but does not directly measure piston displacement or prove how much flow reserve remains. COBB MQB monitor definitions.
  3. If pressure falls short, distinguish a low requested target from an inability to track it. Investigate low-pressure feed, sensor/actuator faults, leaks, restrictions and mechanical or calibration mismatch before attributing the fault to one component. A low-side restriction can limit an upgraded HPFP.
  4. Verify the changed pump against the specific hardware and calibration across cold start, idle, transients and sustained demand. Do not treat pump model coefficients, VCV drive values or ECU monitoring limits as generic power gains. Keep component and pressure protections in place.
  5. Follow the exact manufacturer service procedure for fuel depressurisation and installation. HPFP components are precision parts and the high-pressure circuit is hazardous. Integrated Engineering's specific IEFUVN1 guide stresses cleanliness and experienced installation; it does not cover every pump.

Worked examples

Pump swap on a Simos 18.1 Mk7 GTI (tuner report)

A tuner's report describes fitting a different-generation pump to a Mk7 GTI and copying a donor fuel-mass-per-stroke value. The estimated pump mass at idle was initially about three times injected mass, with oscillating VCV duty and rail pressure; adjusting that value alone did not fully resolve the symptoms. The pulsing later stopped and duty control improved, but no complete confirmed fix was disclosed. The ratios are reported model/log quantities, not measured pump flow, and the donor value should not be copied as a general solution. COBB's supported-MQB monitor list explicitly identifies rail fuel mass delivered and effective pump volume as modelled, and lists separate HPFP proportional and integral controller monitors.

Rail pressure below specification at 100% duty (owner report)

A modified Mk7 GTI with a GT2260S turbo was reported to show rail pressure falling below its specified value during a pull, high direct-injection pulse width and an indicated "HPFP duty cycle" of 100%, despite two replacements of the upgraded HPFP and a lower-mileage LPFP. The report does not establish the ECU software, the precise duty signal, or a confirmed cause or repair. It illustrates why pressure target and actual, low-side supply and the correctly identified pump and injection channels should be assessed together: the indication and component replacements alone do not identify the restriction or failed part.

Overpressure and sensor plausibility codes (owner report)

A Mk7 GTI was reported to cut power and set P0088 and P0191 after upgraded HPFP internals were fitted and the tune was changed from petrol to E85. The owner later reported that the car ran well on E85; the exact calibration, blend, pressure traces and root cause were not independently established. A separate, similar experience was reported by another participant with suggested causes; those suggestions do not establish that ethanol deposits, pump break-in or a sensor fault caused either car's problem. P0088 and P0191 warrant vehicle-specific pressure-control, sensor and electrical diagnosis; they do not by themselves prove a particular component failed.

See also Simos 18 fuel temperature modelling and compensation for temperature-model maps, injection and pump corrections, and measured versus modelled channels.

Related: direct injection and fuel pressure · low pressure fuel pump · direct injection timing · fuel system and MPI upgrades · ethanol and flex fuel.

Sources

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.