Tuning Wiki

Injector catalogue › Diesel injectors › Diesel injector testing

Testing guides: On-vehicle checks | Common-rail bench testing | Equipment | Results and coding | Mechanical, unit and HEUI.

Choose equipment by the injector's complete number, actuator and pressure/flow requirements, not the machine's brand alone. Check the installed adapters, driver, software, licence, test-fluid requirements and test plan. A machine may support screening but not full calibration, or may test a nozzle without testing a complete unit injector.

On-vehicle diagnostic tools

EquipmentUseLimit
Scan tool and electrical test equipmentFault memory, commanded/measured rail pressure, balance data and supported circuit checksDoes not directly measure individual nozzle delivery or prove an injector is within bench specification.
Return-flow kit and approved adaptersCollects or evaluates injector back-leakage under a specified cranking or running procedureSome systems need return back-pressure; use the correct system-specific kit and limits.
Delphi sealed-rail kitSupports applicable high-pressure pump and injector return diagnostic proceduresFollow the exact kit and vehicle procedure; not a complete bench calibration.
PicoScope / WPS500X exampleExamines return-pressure pulsations for a supported low-return-pressure solenoid systemPico excludes piezo and higher-return-pressure systems from this particular procedure.

Sources: Delphi diagnosis guidance, Delphi sealed-rail kit and Pico guided test.

Common-rail diesel benches

ExampleManufacturer-described roleCheck before accepting a job
Bosch DCI 200Single-injector common-rail tester; Bosch describes support for selected VCC/NCC technologies and IMA/NIMA coding.Part number, required retrofit kit, active test data and permitted coding method.
Bosch DCI 700Common-rail injector bench; Bosch describes multi-injector clamping and selected Bosch and third-party coverage.Exact injector and approved plan/adapter; IMA/NIMA capability does not imply universal coding.
Bosch EPS 205Automatic tester for supported common-rail injectors and conventional nozzle-holder assemblies; Bosch also lists UI nozzle support with an adapter.A supported UI nozzle test does not automatically mean a full assembled unit-injector test.
Bosch EPS 708Common-rail pump and injector testing platform with supported accessories.Required pump/injector, piezo or third-party kits and matching test data.
Hartridge CRi-ProFour-line common-rail platform. Its brochure describes Delphi-authorised IRIS repair programmes and separate Hartridge all-makes plans.Injector family, active software/licence and whether the requested result or code is covered by the chosen programme.
Hartridge Sabre CRi Master / ExpertAll-makes common-rail injector testing and selected coding functionality.Plan, unlocked test steps, coding coverage and any required cooling or accessories.
Hartridge YDT-35Delphi describes it as a go/no-go diagnostic tester combining electrical checks and visual spray checks.A screening result is not the same as a full multi-point delivery/return calibration or authorisation to issue a code.

Bosch DCI 200; Bosch DCI/EPS diesel test equipment; Hartridge CRi-Pro brochure; Sabre CRi Master; Hartridge YDT-35.

Manufacturer programmes and coding

A test bench's ability to accept an injector is distinct from the test plan and the authority or technical basis of a code. The CRi-Pro brochure distinguishes Delphi IRIS authorised programmes from its separate all-makes plans. Hartridge lists a Continental/VDO approved CRi-PC injector-test licence restricted to approved partners. Its DENSO AVM2-PC software page specifies required hardware and workshop approval. Equipment and access requirements can change; confirm the current coverage for the exact part.

Hartridge describes injector-specific requirements such as forced-air cooling for its DENSO G2/G3 coding workflow in Coding 101. That is a requirement of the stated workflow, not an instruction to apply one generic test sequence to all DENSO injectors.

Other diesel injector equipment

A Bosch EPS 100 hand-operated nozzle-holder tester is for supported conventional nozzle opening pressure, pattern and sealing checks. It is not a complete common-rail electronic injector test. A Hartridge HK1400 cambox is an example of equipment for supported cam-driven electronic unit injectors/pumps; Hartridge Toledo HEUI Master is for supported hydraulically actuated unit injectors. These require their own fixtures and plans. See mechanical and unit injector testing.

Local example

Llandow Tuning's service page says it uses a separate Delphi bench for supported common-rail diesel injectors; it does not identify the model there and states that VW PD injectors are not supported. Confirm the actual injector and service with the workshop.