Tuning Wiki
Browse BMW

Every BMW engine code is a family, and every family in the modern petrol line has a named controller. The full list of families, displacements and years is the BMW automotive engine directory. This page is how those engines were built and which digital motor electronics actually ran them, generation by generation. A figure belongs to the data sheet it is taken from. Where two sheets disagree, both figures are kept.

Reading the engine code

Up to the N52, a code such as N52B30 OL still used the older habits. N is the new-generation series, 52 is the inline-six of that series, B is petrol, 30 is 3.0 litres, and OL is the upper output. UL is the lower output. On the N52 the upper-output engine is also marked AF on the block, below the intake manifold between the knock sensors. The lower-output N52 has no three-stage intake, and it has different programming and a different exhaust. In the US market of that introduction, both the 3.0 and the 2.5 were supplied only as the upper-output engine. The 330i of the introduction takes the 255 horsepower N52B30. The 325i, later in 2005, takes a 215 horsepower 3.0, not a smaller displacement.

From the 2007 six-cylinder additions the TU suffix and the OL/UL letters are dropped. A count at the end of the code is the version, and a single letter is the output class. N52B30O1 is the improved N52 that had been called N52KP. O is the upper output class, M is medium, U is lower, T is top, K is the lowest, and 0 marks a new development. N54B30O0 is the first version of the upper-output 3.0-litre N54.

Seven positions of a BMW engine code, from generation through version
Original diagram of the seven-character code used from the 2007 six-cylinder engines. Position 3 continues onto the next line. Cars built earlier still carry TU, OL and UL.

The first character is the generation. M is a BMW engine up to 2001. N is a BMW engine from 2001. S is an M GmbH engine. W is an engine from outside BMW, the example given being the Tritec used by MINI. The second character is the layout: 4 an inline-four, 5 an inline-six, 6 a V8, 7 a V12, 8 a V10. The third is the system: 0 basic, 1 SULEV or PZEV, 2 Valvetronic, 3 petrol direct injection, 4 direct injection with a turbocharger, 5 double VANOS with Valvetronic, 7 diesel direct injection with a turbocharger. The fourth is the fuel: B petrol, D diesel, E electric, G natural gas, H hydrogen. The fifth is displacement in tenths of a litre, so 25 is 2.5 litres. The sixth is the output class. The seventh, 1 to 9, is the redesign that used to be called TU.

The six before Valvetronic

The inline-six that the N52 replaced had already been through several controllers. The M20 used two valves per cylinder, a timing belt and adjustable valves, and was built both with carburettors and with injection. The M30 kept two valves and an adjustable valvetrain, dropped the belt, and went up to 3.5 litres. It was the large six until the V8s of 1993.

The M50, from 1992, is the four-valve, twin-cam successor of the M20, with stationary direct ignition and fully sequential injection under DME 3.1. The technical update of 1993 adds intake-only VANOS, cylinder-selective knock control, a hot-film air-mass meter and secondary ignition monitoring. See Bosch Motronic 3 for that generation of Bosch controller.

The M52 TU, fitted to the E46 323i and 328i, is the next mechanical step. The 2.8 runs from June 1998 to June 2000. The 2.5 runs from June 1998 to September 2000. The brief for that engine was lower consumption and emissions with more output than the M52 it replaced. Siemens MS42.0 is the controller developed with those mechanical changes so the engine could meet the low-emission standard of that market. Double VANOS, the map-controlled thermostat and the turbulence intake are part of the same engine, not a later accessory. The M52 and S52 page holds the variant list.

The M54 keeps that shape and changes the mechanics for emissions and economy. On the M54B30 sheet the output is 225 horsepower at 5,900 rpm and 300 Nm at 3,500 rpm, with a bore of 84 mm, a stroke of 89.6 mm and a compression ratio of 10.2:1. The pistons have a shorter skirt than the M52 TU and keep the graphite coating. The rings are changed for the same emissions and friction reasons. The controller named with that engine is MS43. By the E60 525i and 530i, the US cars use MS45.1. Those two E60 engines are 2,494 cc and 2,979 cc, bore and stroke 84 by 75 mm and 84 by 89.6 mm, 184 and 225 horsepower at 6,000 and 5,900 rpm, 175 and 214 ft lb at 3,500 rpm, idle 640 rpm, maximum 6,500 rpm, compression 10.5 and 10.2, four valves, premium unleaded, knock control, firing order 1-5-3-6-2-4, and ULEV II. The E60 intake puts a compact hot-film meter straight into the clean-air outlet of the filter, with no grille in front of it, and the filter housing is about 13 litres. The stainless exhaust is one piece as far as the manifolds, with a 4.8 litre middle silencer and a 26.2 litre rear silencer. There is no viscous fan. The cooling module uses an electric fan.

ME 7.2 on the eight-cylinder

ME 7.2 is the Bosch controller that replaces M5.2.1 for the eight-cylinder applications of that change, including the technical-update M62. The letters are Motronic with electronic throttle. The module is a 134-pin shell in the electronics box, built by Bosch to the BMW specification of that car. Diagnosis uses KWP2000. The same module carries the electronic throttle, cruise control, DSC torque reduction, VANOS, an altitude sensor, an electronics-box temperature sensor and the box fan, one-touch starting, oxygen-sensor heating, the rev limit and the road-speed limit, an active Hall sensor on the camshaft, single-speed secondary air, the electrically heated thermostat already used on the previous M62, long-life plugs, and the auxiliary fan request for the climate control.

The driver's request is two potentiometers in the pedal module. The control unit compares that request with a map and drives the throttle motor with a proportional high and low switch. Two feedback potentiometers on the throttle tell it whether the plate went where it was sent. If the two pedal signals do not agree, the unit keeps the lower one. Response is slower and full throttle is no longer available. Pressing the brake in that state forces the plate and the injection back to idle. The cluster then shows the engine emergency programme, and the pedal fault is stored. Idle, cruise, stability-control intervention and the maximum engine and road speeds are all done with the same plate, not with a separate bypass or a cruise actuator.

ME 9.2 and the N62

The N62 is where Valvetronic enters this generation. ME 9.2 is the Bosch controller for the engine as a whole. A separate Valvetronic control module commands intake-valve lift. Both sit in the electronics box with the integrated voltage supply, and the engine controller runs a fan in the floor of the box that draws air from the passenger compartment. Programme, fault memory and adaptation values are in flash EEPROM. The shell is again 134 pins, in five modules of 9, 24, 52, 40 and 9 pins.

Air on that system is Valvetronic, the electronic throttle, the hot-film meter and a variable intake. Fuel is supply and injection. Ignition is direct, with knock control and ignition monitoring. Emissions are secondary air, oxygen sensors before and after the catalyst on each bank, sensor heating, misfire detection, evaporative purge and leak testing, and the malfunction lamp. The performance side is bi-VANOS on both cams of both banks, oil condition, the electric cooling fan, the alternator, the electronics-box fan, comfort start and cruise. Four knock sensors and four camshaft sensors match the two banks. A barometric sensor is inside the controller. The basic input and output behaviour that had not changed is the same work the previous Bosch systems already did. What is new is the split between the engine controller and the Valvetronic controller, and the emissions hardware required with it.

The N73 and two direct-injection controllers

The N73B60 is the 60-degree V12 that follows the M73, and it is a different fuel system. Against the M73B54 on the same sheet, displacement goes from 5,379 cc to 5,972 cc, bore and stroke from 79 by 85 mm to 89 by 80 mm, and cylinder spacing from 91 mm to 98 mm. Main bearings go from 75 mm to 70 mm. Connecting-rod big ends go from 48 mm to 54 mm. Output goes from 240 kW at 5,000 rpm and 490 Nm at 3,900 rpm to 320 kW, 438 horsepower, at 6,000 rpm and 600 Nm at 3,950 rpm. Idle falls from 600 rpm to 550 rpm. The governed maximum stays 6,500 rpm. Compression rises from 10:1 to 11.3:1. Valves go from two per cylinder to four. Intake valve diameter falls from 42 mm to 35 mm and exhaust from 36 mm to 29 mm, because the lift is no longer a fixed cam. Intake lift is 0.3 to 9.85 mm. Exhaust lift is 9.7 mm, against 10.3 mm on both valves of the M73. The engine weighs 280 kg. Fuel is premium unleaded. Knock control stays. Injection pressure rises from 3.5 bar to a range of 50 to 120 bar. Consumption is given as 12 percent lower than the M73. Regulated top speed stays 250 km/h. Firing order is unchanged: 1-7-5-11-3-9-6-12-2-8-4-10. The emissions level on that sheet is LEV.

The controllers on that sheet are two MED 9.2.1 units, a Valvetronic control unit, and two HDEV control units. The M73 it replaces used two ME 5.2 units and the earlier electronic-throttle system. The intake manifold is a magnesium shell, one chamber for each bank, bonded and bolted, and the halves are not to be separated. It is dip-coated, including the bolts for the attached parts. Those bolts are replaced if they are damaged, because the coating is what stops the corrosion. Gaskets are captured. Rubber elements on the bolts isolate the manifold from the engine. Each bank has a manifold pressure sensor, a throttle, and a pressure-control valve for the crankcase ventilation.

The N52 and MSV70

The N52 is the first of these six-cylinder engines to use Valvetronic, and the first of them to use MSV70. It was introduced on the E60, E61 and E90, with later model lines to follow. Against the M54 and M56, the module states a further 12 percent reduction in consumption and a 10 percent gain in the dynamics it is measuring, enough for ULEV II. The comparison with the M54 quotes 55 kW per litre and 1.0 kg per kW for the M54, and 61.7 kW per litre and 0.82 kg per kW for the N52. The data sheet for the 255 horsepower N52B30 itself gives 63.4 kW per litre and 0.84 kg per kW. Both pairs are in the same account. The sheet is the one to use for that particular engine.

That N52B30 sheet reads: inline-six, 2,996 cc, stroke and bore listed as 85.0/88.0 mm, cylinder spacing 91 mm, six main bearings of 56 mm and one of 65 mm, rod journals 50 mm, firing order 1-5-3-6-2-4, 190 kW and 255 horsepower at 6,600 rpm, 300 Nm from 2,500 to 4,000 rpm, governed cut at 7,000 rpm, compression 10.7, four valves, intake valve 34.2 mm, exhaust valve 29 mm, intake lift from 0.18 mm to 9.9 mm, exhaust lift 9.7 mm, intake opening angle 255 crank degrees, exhaust 263, intake spread adjustable from 120 to 50, exhaust spread from 115 to 60, weight 161 kg, fuel 91 listed together with 98 RON, oil SAE 5W-30, knock control, three-stage resonance intake, Siemens MSV70, Valvetronic II, ULEV 2. A later sheet for the medium-output N52B30M1 lists stroke and bore as 88/85 mm under the same style of heading, 2,996 cc, 172 kW and 230 horsepower at 6,250 rpm, 270 Nm at 3,000 rpm, the same 7,000 rpm and 10.7 compression, manifold injection and MSV80. The two sheets do not agree which of 85 mm and 88 mm is the stroke.

The crankcase is the weight saving. Magnesium cannot carry every job in the block, so an aluminium-silicon insert is cast into a magnesium shell and cannot be separated from it. The insert takes the threads for the transmission, the cylinder head and the main bearings, and it takes the coolant passages, so coolant does not sit against magnesium. The alloy used for the shell is AJ62, chosen because it machines and because it is less willing to corrode. The bedplate is magnesium as well. The timing cover is cast as part of the block rather than bolted on. Cylinder bores are Alusil, with no iron liner of the sort used on the previous six. The bores are not machined. The deck can still be planed. Connecting rods are trapezoidal and lightened. The head is aluminium-silicon. The head gasket uses a silicon sealing lip. VANOS is the lighter double-VANOS. The oil pump is controlled by volume. The coolant pump is electric. Crankcase ventilation is heated. The upper-output engine has the three-stage intake.

MSV70 is Siemens/VDO. The letters are Siemens motor control with Valvetronic, and this is the first Valvetronic system on a BMW six. The housing is aluminium. Two main connectors break into seven modules, 146 pins in all: 26, 26, 6, 6, then 44, 12 and 26. The processor clock is 60 MHz. The controller is responsible for ignition, injection, Valvetronic II, the lightened double VANOS, the mapped thermostat, the electric coolant pump, knock, lambda, tank ventilation, the air-conditioning compressor request, the three-stage intake, the electric fuel pump, cruise, the alternator, the crankcase-ventilation heater, oil condition and oil level, the intelligent battery sensor, substitute values, and its own diagnosis. It meets the 2006 ULEV II on-board diagnosis rules for this engine.

Ambient temperature and ambient pressure are measured inside the controller. Valvetronic has its own relay, its own motor and an eccentric-shaft sensor. There are two knock sensors, one for cylinders 1 to 3 and one for 4 to 6, two camshaft sensors, a crankshaft sensor, two intake actuators, a hot-film meter, a differential-pressure sensor, a sport button, and a secondary-air pump with a meter of its own. Oxygen sensors, the pedal module, the throttle, clutch and brake switches, the access system and the stability system are on the same picture. One air-flap magnet on that overview is marked as not used for the US cars. Power is the usual battery, ignition and ground path, with the engine fuses and a main relay. The workshop network is PT-CAN.

Valvetronic II is the load control. The throttle is still there, but the air the cylinder receives is set by how far the intake valve opens. The eccentric shaft, read by its sensor, is the feedback. Double VANOS still moves the timing of both cams. The three intake stages are idle and low speed, the middle of the range, and the top of the range, each with its own actuator path.

N52KP, N51 and MSV80

The N52KP, formally N52B30O1 and the cars around it, is the cost-reduced and revised N52, and it replaces the original N52 model by model. The first of them in that account is the 328i coupe from September of that model year. MSV80 is the controller named for it. The hardware called out with that change is a digital hot-film meter, an EGAS 8 throttle, a plastic valve cover that now contains the crankcase vent valve and the oil separator, stronger connecting rods, exhaust-valve stems increased to 6 mm, a second-generation electric water pump, and hydroformed camshafts. Three output classes are named: O1 at 260 horsepower, M1 at 230 horsepower, and a possible U1 at 215 horsepower. The upper-output example given is the E83 life-cycle X3 3.0si, 260 horsepower at 6,600 rpm.

EGAS 8, from Siemens/VDO, is the throttle used across the new six-cylinder variants of that year. The plate is plastic. The older throttle reported its position with a potentiometer. This one uses a contactless magnetoresistive sensor.

The N51 is the SULEV II version of the same six, phased into selected cars from September 2006, and it carries over ideas from the earlier SULEV M56, including a zero-evaporation fuel system. The measures named for it are a catalyst close to the engine plus an underbody catalyst, secondary air, a revised combustion chamber, pistons with a lower compression, the plastic valve cover from the N52KP, stainless fuel lines with threaded joints, a radiator with a Prem-air coating, the EGAS 8 throttle, an airbox with an activated-carbon filter for the evaporative system, and purge pipes in a plastic chosen for that duty. The spark plugs of the N51 and the N52KP stay the N52 plug. The N54 does not.

The N54, two small turbos, and piezo injection

The N54 is the turbocharged six, first in the E92 335i from September 2006. The introduction sheet calls it N54B30O0 and gives an inline-six of 2,979 cc, 225 kW and 300 horsepower at 5,800 rpm, 400 Nm from 1,300 to 5,000 rpm, a 7,000 rpm maximum, compression 10.2, four valves, inlet valve 31.44 mm, exhaust valve 28 mm, cylinder spacing 91 mm, main journals 65 mm, rod journals 50 mm, weight 187 kg, 0.83 kg per kW, 75.5 kW per litre, firing order 1-5-3-6-2-4, knock control, ULEV II, and second-generation high-pressure injection. The crankcase is aluminium with iron liners, in dimensions described as close to the N52. The head is aluminium with a plastic cover. The crankshaft is steel. There is an external oil cooler and a 400 watt electric water pump. Bi-VANOS stays. The controller named at that introduction is MSD80.

A later comparison, an E71 X6 xDrive35i with N54B30O0 against an F07 535i with N55, lists the same 2,979 cc and the same 10.2 compression, bore and stroke 84.0 by 89.6 mm, 225 kW and 306 horsepower from 5,800 to 6,250 rpm, and 400 Nm from 1,300 to 5,000 rpm. The controller in that N54 column is MSD81, and the US emissions line is ULEV. The US model table for the E82, E88, E90, E92 and E93 cars lists 300 SAE horsepower from 5,800 to 6,250 rpm and 407 Nm, written there as 300 ft lb, from 1,400 to 5,000 rpm, and it prints stroke and bore as 89.6/84.0 mm. The 335is and the Z4 sDrive35is are listed at 320 SAE horsepower and 450 Nm, and an overboost function on those cars adds about 37 ft lb for about five seconds, to a peak described as 369 ft lb. MSD80 is the name at the 2006 introduction. MSD81 is the name on the later comparison. They are not the same label.

The turbos are small and parallel. Cylinders 1, 2 and 3 drive one. Cylinders 4, 5 and 6 drive the other. A smaller rotating mass reaches boost sooner, which is the reason given for using two of them instead of one large one. The turbine and compressor can reach 200,000 rpm. Exhaust at the turbine inlet can reach 1,050 °C, so each turbo is on both the oil circuit and the coolant circuit. The electric coolant pump can keep moving coolant after the engine has stopped, so the oil in the bearing housing is not left to cook. Each bank has a wastegate and a blow-off valve. Charge air is cooled in an air-to-air intercooler. The intake path includes a charge-pressure and temperature sensor and a manifold pressure sensor.

High-pressure injection is the second generation, quoted to 200 bar, with piezo injectors that open outwards. The N54 spark plug is not the N52 plug. It is a Bosch plug with a 12 mm thread, against 14 mm on the N52, so the two cannot be installed in each other's heads, and the hex is a 12-point that needs a thin-wall socket.

The N55 and MEVD17.2

The N55 keeps the 3.0-litre turbo six and changes the hardware around it. On the F07 535i sheet the N55B30M0 matches the compared N54 at 225 kW, 306 horsepower, 400 Nm and 10.2 compression, with the power band extended to 6,400 rpm and the torque available from 1,200 rpm. Combined European consumption on that pair of cars falls from 10.9 to 8.9 litres per 100 km, and CO2 from 262 to 209 g/km. The US emissions line moves from ULEV to ULEV II. The controller is MEVD17.2.

There is one twin-scroll turbo, with a vacuum wastegate that the electronics command, and an electric diverter valve built into the compressor housing. The intercooler is still air-to-air, low in the front bumper. There is no underbody catalyst. The intake layout is otherwise the N54 arrangement, with a different manifold because there is only one turbo. The vacuum pump is the two-stage unit already used on the N54, and the vacuum reservoir is built into the cylinder-head cover.

Fuel is the high-pressure system, but the injectors are solenoid valves rather than the piezo injectors of the N54. The high-pressure pump and the pressure sensors are described as the same sort of parts in both systems. Oil delivery is simplified: the inlet, the deflector and the collector are one piece, and the pump uses a Duroplast slide valve controlled from a map in the engine controller. The controller itself is bolted to the intake manifold and cooled by the intake air, which is also what lets the same engine drop into several platforms.

The S85 and MSS65

The S85 is the Motorsport V10. On the sheet set beside the P84/5 Formula One engine it is a 90-degree V10 with four valves per cylinder, 4,999 cc, bore 92 mm and stroke 75.2 mm, 373 kW and 500 horsepower at 7,750 rpm, 520 Nm at 6,100 rpm, a maximum of 8,250 rpm and a compression ratio of 12:1. The block and bedplate follow the stiffening idea of the N52. The oil system is a dry sump, and the controller has to run two electric scavenge pumps while the car is cornering.

MSS65 is the Siemens controller developed with Motorsport for that engine, and it is a development of MSS54 rather than of MSV70. The car still has to meet LEV 2. The circuit board has more than 1,000 parts and three 32-bit processors, together stated as more than 200 million engine calculations a second. More than 50 inputs are monitored. The jobs called out for it are the ten individual throttles, those two scavenge pumps, fuel delivery that follows demand, and ionic-current measurement used both for knock and for misfire. The housing is aluminium, again with seven connector modules. The car's powertrain CAN remains. Two local CAN networks are added: one for the throttle motors, and one for idle control which also reaches the sequential gearbox. A bit-serial link joins the controller to the oil-condition sensor, the intelligent battery sensor and the alternator. An NTC inside the controller watches the electronics box and switches the box fan. The fan is also pulsed at every start so that it does not sit long enough to seize. On the M5 and M6 the battery feed is a 7.5 amp fuse, fuse 26 in the front holder behind the glovebox. Ignition-on arrives both as a bus signal and as a hard wake-up from the access system. The controller then closes its main relay and feeds the three fuse carriers in the electronics box.

BMW engines paired with the controller used on that generation
Original diagram of the controller named for each of these engines. MSD80 is the N54 name at introduction. MSD81 is the name on the later N54 comparison. The N52 stroke figures differ between its own data sheets and are not settled by this pairing.

What stays the same

Across these controllers the workshop question is the same one. Which device is allowed to move the air, which device meters the fuel, and which faults are allowed to substitute a value instead of opening the plate. On ME 7.2 the plate is the load control, and a disagreed pair of pedal tracks falls back to the lower track and then to idle if the brake is pressed. On MSV70 and ME 9.2 the intake valve lift is the load control, and the throttle is still fitted and still watched. On the N54 and N55 the turbos and the high-pressure injectors are added to that chain, piezo on the N54 and solenoid on the N55. On the S85 the ten throttles and the ionic knock measurement replace the single-plate and knock-sensor arrangement of the production six. The diesel families in the directory, from the M21 through the B57, use their own controllers and are not these petrol systems.