Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engines
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 3 to revision 3

Removed text is struck through; added text is highlighted.

A diesel injection pump has to put a measured quantity of fuel into the cylinder at a chosen moment, at a pressure high enough to open the nozzle and break the fuel up. The systems differ in where that pressure is made, and in what moves to change the quantity. An in-line pump, a distributor pump, a unit injector and a common rail are not four ways of doing the same job with the same adjustments.

Bosch's 2001 overview groups them as in-line pumps (PE), distributor pumps (VE and VR), the unit injector (UIS), the unit pump (UPS) and common rail (CRS). The mechanical flyweight governor was already being replaced by electronic diesel control on the pumps that still used a rack or a collar. Bosch, Electronic Diesel Control, 2001. How each one is tuned is tuning diesel injection systems. Common rail, which stores the pressure and meters at the injector, is common-rail diesel fuel systems. Hydraulic unit injection, which uses engine oil rather than a fuel pump to make the injection pressure, is HEUI.

SystemWhere the high pressure is madeWhat sets the quantityNozzle PE in-lineOne cam-driven plunger per cylinder, inside the pumpA control rack turns each plunger so a helix ends the effective stroke sooner or laterSpring-loaded. Opens at a set pressure. Control-sleeve in-lineThe same plungersThe same rack, plus a sleeve that moves the start of deliverySpring-loaded VE distributorOne axial plunger, or radial pistons, feeding every cylinder in turnA control collar, or a high-pressure solenoidSpring-loaded Unit injector (UIS)A plunger in each injector, driven from the engine camHow long the high-pressure solenoid stays closedSpring-loaded, in the same unit Unit pump (UPS)A cam-driven pump per cylinderThe same solenoid timingSpring-loaded holder, on a short high-pressure line Common railA supply pump keeps a shared rail chargedWhen, and for how long, the injector is electrically openedElectrically operated. Pressure is already in the rail.

The spring-loaded nozzle

On an in-line pump, a distributor pump, a unit injector and a unit pump, the nozzle is a needle held shut by a spring. Fuel pressure lifts the needle. When the pressure falls, the spring seats it again. Bosch calls the pressure that lifts it the nozzle-opening pressure, and on a standard holder that pressure is the spring's initial tension, set with a shim. Injection ends when the pressure has fallen far enough for the spring to close the needle. These are the injectors workshops call pop injectors: they pop open at a pressure, and they have no solenoid of their own.

The nozzle has to match the chamber. Pintle nozzles (DN) are the indirect-injection type, for pre-chamber and swirl-chamber engines. A throttling pintle opens a small gap first and the main spray later, which softens the combustion. Hole-type nozzles (DLL and DLSA in Bosch's marking) are the direct-injection type. The number and diameter of the holes follow the quantity, the chamber shape and the air swirl. A two-spring holder puts two springs one behind the other. The first spring sets the initial opening pressure and a stop sleeve limits the first lift, so a small volume goes in before the needle opens fully. Bosch describes that two-stage rate as a way to soften idle and part-load combustion. It is a shaped nozzle, not a common-rail pilot that an ECU can move.

A needle-motion sensor in the holder produces a signal when the needle lifts. That signal is the start of injection at the nozzle. It is not the same instant as the start of delivery inside the pump. On a distributor pump the pressure wave still has to travel the high-pressure line. Diesel injection timing and EDC15 injection systems keep those two events apart.

Why the VE pump advances delivery with speed: Bosch’s VE technical instruction explains that pump start of delivery follows inlet-port closure; pressure then builds to the nozzle-opening threshold, when the needle lifts and injection begins. Bosch calls the interval between pump delivery start and nozzle injection start “injection lag”. It describes pressure-wave travel time along the high-pressure line as essentially independent of engine speed, so the crank-angle gap between those events grows as speed rises. The VE timing device advances pump start of delivery with speed to compensate for injection and ignition lag. This is a Bosch axial-piston VE example; confirm event definitions and control behaviour for the exact pump and ECU. Bosch, Diesel distributor fuel-injection pumps VE: Technical Instruction, 4th ed. (1999), printed pp. 29–30; public PDF mirror.

In-line pumps

A standard PE in-line pump has a barrel and plunger for each cylinder. The pump's own camshaft lifts the plunger a fixed distance and a spring returns it. High pressure starts at the moment the top edge of the plunger covers the inlet port. That moment is the start of delivery. The plunger keeps rising, pressure opens the nozzle, and injection stops when a helix machined into the plunger uncovers the inlet port and the pressure collapses. The travel between those two events is the effective stroke.

A control rack rotates every plunger together. Rotating the plunger moves the helix relative to the port, so the effective stroke, and the quantity, changes. The rack is moved by a mechanical flyweight governor or by an electrical actuator. Plunger lift itself does not change. On a standard PE the start of delivery is the port closing under the plunger's top edge. It is not an independent timing lever.

The control-sleeve in-line pump adds that lever. A sleeve slides on the plunger and an actuator shaft moves it, which changes how far the plunger rises before it closes the inlet port, and therefore the start of injection. Bosch treats this as a degree of freedom the standard PE does not have: start of injection can be moved without relying on engine speed alone. Quantity is still the rack and the helix.

PF single-plunger pumps are the external-drive relation of the PE. The F in the designation is the external drive: the cams are on the engine camshaft, not in the pump, so the pump camshaft cannot be turned to set the timing. Quantity still arrives from a governor or a controller through a rack. Bosch places them on small engines, locomotives, marine engines and construction machinery. Timing, where it is adjusted, is an intermediate element or a solenoid, not a rotation of the engine camshaft.

An in-line pump with an ECU

Electronic control does not replace the helix. Bosch's PE-EDC description keeps quantity as a function of control-rack position and engine speed. A linear magnet on the pump moves the rack. With the solenoid de-energised, a spring pushes the rack to the stop and fuel delivery stops. More current moves the rack towards more fuel, and the current is a pulse-width-modulated signal, so the rack can sit anywhere between zero and full delivery. A rack-travel sensor tells the ECU where the rack actually is, and the position control corrects it.

The ECU holds a pump map. From engine speed and the desired quantity it calculates the rack travel that should produce that quantity. The control law can be given a shape taken from the mechanical RQ and RQV governors. The injector at the end of the pipe is still the spring nozzle.

On the control-sleeve pump the quantity path is the same, and a second actuator moves the sleeve. Bosch states that a low current in the start-of-delivery solenoid retards the start of delivery, and a high current advances it. A standard PE-EDC without that sleeve does not gain this second actuator just because it has an ECU. The sleeve is the hardware that makes start of delivery a separate command.

Distributor pumps

A distributor pump has one high-pressure pumping mechanism for all the cylinders. A vane supply pump fills the high-pressure chamber. An axial piston, driven by a cam plate with one lobe per cylinder, or two to four radial pistons inside a cam ring, makes the pressure. A rotating distributor opens the outlets in turn. Radial pistons can make a higher pressure than the axial piston, and the pump has to be built for it. Bosch notes that every radial-piston distributor pump in this description is solenoid-valve controlled.

On the port-and-helix VE, a control collar sets the effective stroke and therefore the quantity, whether a flyweight governor moves the collar or an electronic actuator does. The timing device rotates the roller ring and that rotation is the pump's start of delivery. In the VE-EDC arrangement a moving-magnet actuator turns the collar through a shaft, and a Hall sensor reports the angle. Return springs set delivery to zero when the actuator is de-energised. A separate timing-device solenoid is the electronic timing path. The EDC15V example of this pump is in EDC15 injection systems.

On the solenoid-valve pumps the collar is replaced by a high-pressure solenoid. While the valve is closed, pressure can build. When it opens, fuel escapes, pressure does not build, and that cylinder is not injected. The same valve therefore meters the quantity and takes part in the start of injection. The control signals come from a pump ECU, an engine ECU, or both. VP30 is the axial-piston form and VP44 the radial-piston form in Bosch's EDC15M example. A VP44 name does not say whether the controller is on the pump. VP44 and PSG16 is the pump-mounted controller that combines engine and pump functions. On the 2001 Saab 9-3 D223L the engine ECU sends a fuel mass and a timing request to the pump over a separate bus, and the pump meters and builds pressure.

Unit injectors and unit pumps

A unit injector puts the pumping element and the nozzle in one body, one per cylinder, in the head. The engine cam drives it directly or through a rocker. There is no high-pressure line between a pump and a nozzle, which is why Bosch, in 2001, could quote injection pressures up to 2,050 bar for the UIS. The ECU calculates the injection, and a high-pressure solenoid valve opens and closes to control it.

A unit pump uses the same idea and splits the hardware. The pump is driven from the engine camshaft. A short high-pressure line, matched to that pump and nozzle, joins it to a nozzle holder. Installation is easier because the pump and the holder are not one piece. Start and duration are still the solenoid.

The nozzle on both is still a pop nozzle. Bosch defines the start of delivery, the BIP (begin of injection period), as the instant the solenoid closes. Pressure then rises in the pump chamber. The nozzle opens when nozzle-opening pressure is passed, and that later instant is the start of injection. Fuel is metered in the delivery period between solenoid closure and the end of the trigger. The ECU reads the solenoid current to find the closing point, so a needle sensor is not required. If that BIP signal fails, Bosch describes a change to open-loop control. One unwanted injection is the failure Bosch treats these systems as able to limit themselves to, because an open solenoid spills the pressure.

Volkswagen's pumped-nozzle engines and the commercial-vehicle unit pumps are this family, not a common rail. Pressures, the Volkswagen applications and the large-engine unit are on diesel unit-injector systems. The EDC16 V10 and V6 contrast is in EDC16 torque and fuel.

Common rail is a different pump

A common-rail supply pump does not meter the cylinder's fuel with a helix or a collar. It keeps a rail at a commanded pressure, and the injector, opened electrically, decides the moment and the duration. Injection pressure can stay high at low speed, which is where a distributor pump is weakest, and more than one injection per stroke is normal. The pumps, the pressures and the four manufacturers' hardware are already set out in common-rail diesel fuel systems and common-rail supply pumps. The injector is not a shimmed pop holder: common-rail diesel injectors.

Sources

Robert Bosch GmbH, Electronic Diesel Control (EDC), 2001, independent PDF mirror. PE and control-sleeve in-line pumps, distributor pumps, UIS and UPS, PE-EDC rack and sleeve actuators, VE-EDC collar actuator, nozzle-opening pressure and BIP. The designs chapter and the triggering chapter, including the PE-EDC and VE-EDC sections. Accessed 2026-11-13. Robert Bosch GmbH, Diesel distributor fuel-injection pumps VE: Technical Instruction, 4th ed., April 1999, order no. 1 987 722 164, public PDF mirror hosted by injectionpumps.co.uk. Injection lag and the speed-dependent timing device (printed pp. 29–30); nozzle-opening pressure, two-spring holders and needle-motion sensing (printed pp. 50–52). Accessed 2026-11-18. EDC15 injection systems and timing feedback and VP44 and PSG16. This wiki. The EDC15V, EDC15M and Saab VP44 cases.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: Diesel injection pumps

A diesel injection pump has to put a measured quantity of fuel into the cylinder at a chosen moment, at a pressure high enough to open the nozzle and break the fuel up. The systems differ in where that pressure is made, and in what moves to change the quantity. An in-line pump, a distributor pump, a unit injector and a common rail are not four ways of doing the same job with the same adjustments.

Bosch's 2001 overview groups them as in-line pumps (PE), distributor pumps (VE and VR), the unit injector (UIS), the unit pump (UPS) and common rail (CRS). The mechanical flyweight governor was already being replaced by electronic diesel control on the pumps that still used a rack or a collar. Bosch, Electronic Diesel Control, 2001. How each one is tuned is tuning diesel injection systems. Common rail, which stores the pressure and meters at the injector, is common-rail diesel fuel systems. Hydraulic unit injection, which uses engine oil rather than a fuel pump to make the injection pressure, is HEUI.

SystemWhere the high pressure is madeWhat sets the quantityNozzle
PE in-lineOne cam-driven plunger per cylinder, inside the pumpA control rack turns each plunger so a helix ends the effective stroke sooner or laterSpring-loaded. Opens at a set pressure.
Control-sleeve in-lineThe same plungersThe same rack, plus a sleeve that moves the start of deliverySpring-loaded
VE distributorOne axial plunger, or radial pistons, feeding every cylinder in turnA control collar, or a high-pressure solenoidSpring-loaded
Unit injector (UIS)A plunger in each injector, driven from the engine camHow long the high-pressure solenoid stays closedSpring-loaded, in the same unit
Unit pump (UPS)A cam-driven pump per cylinderThe same solenoid timingSpring-loaded holder, on a short high-pressure line
Common railA supply pump keeps a shared rail chargedWhen, and for how long, the injector is electrically openedElectrically operated. Pressure is already in the rail.

The spring-loaded nozzle

On an in-line pump, a distributor pump, a unit injector and a unit pump, the nozzle is a needle held shut by a spring. Fuel pressure lifts the needle. When the pressure falls, the spring seats it again. Bosch calls the pressure that lifts it the nozzle-opening pressure, and on a standard holder that pressure is the spring's initial tension, set with a shim. Injection ends when the pressure has fallen far enough for the spring to close the needle. These are the injectors workshops call pop injectors: they pop open at a pressure, and they have no solenoid of their own.

The nozzle has to match the chamber. Pintle nozzles (DN) are the indirect-injection type, for pre-chamber and swirl-chamber engines. A throttling pintle opens a small gap first and the main spray later, which softens the combustion. Hole-type nozzles (DLL and DLSA in Bosch's marking) are the direct-injection type. The number and diameter of the holes follow the quantity, the chamber shape and the air swirl. A two-spring holder puts two springs one behind the other. The first spring sets the initial opening pressure and a stop sleeve limits the first lift, so a small volume goes in before the needle opens fully. Bosch describes that two-stage rate as a way to soften idle and part-load combustion. It is a shaped nozzle, not a common-rail pilot that an ECU can move.

A needle-motion sensor in the holder produces a signal when the needle lifts. That signal is the start of injection at the nozzle. It is not the same instant as the start of delivery inside the pump. On a distributor pump the pressure wave still has to travel the high-pressure line. Diesel injection timing and EDC15 injection systems keep those two events apart.

Why the VE pump advances delivery with speed: Bosch’s VE technical instruction explains that pump start of delivery follows inlet-port closure; pressure then builds to the nozzle-opening threshold, when the needle lifts and injection begins. Bosch calls the interval between pump delivery start and nozzle injection start “injection lag”. It describes pressure-wave travel time along the high-pressure line as essentially independent of engine speed, so the crank-angle gap between those events grows as speed rises. The VE timing device advances pump start of delivery with speed to compensate for injection and ignition lag. This is a Bosch axial-piston VE example; confirm event definitions and control behaviour for the exact pump and ECU. Bosch, Diesel distributor fuel-injection pumps VE: Technical Instruction, 4th ed. (1999), printed pp. 29–30; public PDF mirror.

In-line pumps

A standard PE in-line pump has a barrel and plunger for each cylinder. The pump's own camshaft lifts the plunger a fixed distance and a spring returns it. High pressure starts at the moment the top edge of the plunger covers the inlet port. That moment is the start of delivery. The plunger keeps rising, pressure opens the nozzle, and injection stops when a helix machined into the plunger uncovers the inlet port and the pressure collapses. The travel between those two events is the effective stroke.

A control rack rotates every plunger together. Rotating the plunger moves the helix relative to the port, so the effective stroke, and the quantity, changes. The rack is moved by a mechanical flyweight governor or by an electrical actuator. Plunger lift itself does not change. On a standard PE the start of delivery is the port closing under the plunger's top edge. It is not an independent timing lever.

The control-sleeve in-line pump adds that lever. A sleeve slides on the plunger and an actuator shaft moves it, which changes how far the plunger rises before it closes the inlet port, and therefore the start of injection. Bosch treats this as a degree of freedom the standard PE does not have: start of injection can be moved without relying on engine speed alone. Quantity is still the rack and the helix.

PF single-plunger pumps are the external-drive relation of the PE. The F in the designation is the external drive: the cams are on the engine camshaft, not in the pump, so the pump camshaft cannot be turned to set the timing. Quantity still arrives from a governor or a controller through a rack. Bosch places them on small engines, locomotives, marine engines and construction machinery. Timing, where it is adjusted, is an intermediate element or a solenoid, not a rotation of the engine camshaft.

An in-line pump with an ECU

Electronic control does not replace the helix. Bosch's PE-EDC description keeps quantity as a function of control-rack position and engine speed. A linear magnet on the pump moves the rack. With the solenoid de-energised, a spring pushes the rack to the stop and fuel delivery stops. More current moves the rack towards more fuel, and the current is a pulse-width-modulated signal, so the rack can sit anywhere between zero and full delivery. A rack-travel sensor tells the ECU where the rack actually is, and the position control corrects it.

The ECU holds a pump map. From engine speed and the desired quantity it calculates the rack travel that should produce that quantity. The control law can be given a shape taken from the mechanical RQ and RQV governors. The injector at the end of the pipe is still the spring nozzle.

On the control-sleeve pump the quantity path is the same, and a second actuator moves the sleeve. Bosch states that a low current in the start-of-delivery solenoid retards the start of delivery, and a high current advances it. A standard PE-EDC without that sleeve does not gain this second actuator just because it has an ECU. The sleeve is the hardware that makes start of delivery a separate command.

Distributor pumps

A distributor pump has one high-pressure pumping mechanism for all the cylinders. A vane supply pump fills the high-pressure chamber. An axial piston, driven by a cam plate with one lobe per cylinder, or two to four radial pistons inside a cam ring, makes the pressure. A rotating distributor opens the outlets in turn. Radial pistons can make a higher pressure than the axial piston, and the pump has to be built for it. Bosch notes that every radial-piston distributor pump in this description is solenoid-valve controlled.

On the port-and-helix VE, a control collar sets the effective stroke and therefore the quantity, whether a flyweight governor moves the collar or an electronic actuator does. The timing device rotates the roller ring and that rotation is the pump's start of delivery. In the VE-EDC arrangement a moving-magnet actuator turns the collar through a shaft, and a Hall sensor reports the angle. Return springs set delivery to zero when the actuator is de-energised. A separate timing-device solenoid is the electronic timing path. The EDC15V example of this pump is in EDC15 injection systems.

On the solenoid-valve pumps the collar is replaced by a high-pressure solenoid. While the valve is closed, pressure can build. When it opens, fuel escapes, pressure does not build, and that cylinder is not injected. The same valve therefore meters the quantity and takes part in the start of injection. The control signals come from a pump ECU, an engine ECU, or both. VP30 is the axial-piston form and VP44 the radial-piston form in Bosch's EDC15M example. A VP44 name does not say whether the controller is on the pump. VP44 and PSG16 is the pump-mounted controller that combines engine and pump functions. On the 2001 Saab 9-3 D223L the engine ECU sends a fuel mass and a timing request to the pump over a separate bus, and the pump meters and builds pressure.

Unit injectors and unit pumps

A unit injector puts the pumping element and the nozzle in one body, one per cylinder, in the head. The engine cam drives it directly or through a rocker. There is no high-pressure line between a pump and a nozzle, which is why Bosch, in 2001, could quote injection pressures up to 2,050 bar for the UIS. The ECU calculates the injection, and a high-pressure solenoid valve opens and closes to control it.

A unit pump uses the same idea and splits the hardware. The pump is driven from the engine camshaft. A short high-pressure line, matched to that pump and nozzle, joins it to a nozzle holder. Installation is easier because the pump and the holder are not one piece. Start and duration are still the solenoid.

The nozzle on both is still a pop nozzle. Bosch defines the start of delivery, the BIP (begin of injection period), as the instant the solenoid closes. Pressure then rises in the pump chamber. The nozzle opens when nozzle-opening pressure is passed, and that later instant is the start of injection. Fuel is metered in the delivery period between solenoid closure and the end of the trigger. The ECU reads the solenoid current to find the closing point, so a needle sensor is not required. If that BIP signal fails, Bosch describes a change to open-loop control. One unwanted injection is the failure Bosch treats these systems as able to limit themselves to, because an open solenoid spills the pressure.

Volkswagen's pumped-nozzle engines and the commercial-vehicle unit pumps are this family, not a common rail. Pressures, the Volkswagen applications and the large-engine unit are on diesel unit-injector systems. The EDC16 V10 and V6 contrast is in EDC16 torque and fuel.

Common rail is a different pump

A common-rail supply pump does not meter the cylinder's fuel with a helix or a collar. It keeps a rail at a commanded pressure, and the injector, opened electrically, decides the moment and the duration. Injection pressure can stay high at low speed, which is where a distributor pump is weakest, and more than one injection per stroke is normal. The pumps, the pressures and the four manufacturers' hardware are already set out in common-rail diesel fuel systems and common-rail supply pumps. The injector is not a shimmed pop holder: common-rail diesel injectors.

Sources

Revision 3: Diesel injection pumps

A diesel injection pump has to put a measured quantity of fuel into the cylinder at a chosen moment, at a pressure high enough to open the nozzle and break the fuel up. The systems differ in where that pressure is made, and in what moves to change the quantity. An in-line pump, a distributor pump, a unit injector and a common rail are not four ways of doing the same job with the same adjustments.

Bosch's 2001 overview groups them as in-line pumps (PE), distributor pumps (VE and VR), the unit injector (UIS), the unit pump (UPS) and common rail (CRS). The mechanical flyweight governor was already being replaced by electronic diesel control on the pumps that still used a rack or a collar. Bosch, Electronic Diesel Control, 2001. How each one is tuned is tuning diesel injection systems. Common rail, which stores the pressure and meters at the injector, is common-rail diesel fuel systems. Hydraulic unit injection, which uses engine oil rather than a fuel pump to make the injection pressure, is HEUI.

SystemWhere the high pressure is madeWhat sets the quantityNozzle
PE in-lineOne cam-driven plunger per cylinder, inside the pumpA control rack turns each plunger so a helix ends the effective stroke sooner or laterSpring-loaded. Opens at a set pressure.
Control-sleeve in-lineThe same plungersThe same rack, plus a sleeve that moves the start of deliverySpring-loaded
VE distributorOne axial plunger, or radial pistons, feeding every cylinder in turnA control collar, or a high-pressure solenoidSpring-loaded
Unit injector (UIS)A plunger in each injector, driven from the engine camHow long the high-pressure solenoid stays closedSpring-loaded, in the same unit
Unit pump (UPS)A cam-driven pump per cylinderThe same solenoid timingSpring-loaded holder, on a short high-pressure line
Common railA supply pump keeps a shared rail chargedWhen, and for how long, the injector is electrically openedElectrically operated. Pressure is already in the rail.

The spring-loaded nozzle

On an in-line pump, a distributor pump, a unit injector and a unit pump, the nozzle is a needle held shut by a spring. Fuel pressure lifts the needle. When the pressure falls, the spring seats it again. Bosch calls the pressure that lifts it the nozzle-opening pressure, and on a standard holder that pressure is the spring's initial tension, set with a shim. Injection ends when the pressure has fallen far enough for the spring to close the needle. These are the injectors workshops call pop injectors: they pop open at a pressure, and they have no solenoid of their own.

The nozzle has to match the chamber. Pintle nozzles (DN) are the indirect-injection type, for pre-chamber and swirl-chamber engines. A throttling pintle opens a small gap first and the main spray later, which softens the combustion. Hole-type nozzles (DLL and DLSA in Bosch's marking) are the direct-injection type. The number and diameter of the holes follow the quantity, the chamber shape and the air swirl. A two-spring holder puts two springs one behind the other. The first spring sets the initial opening pressure and a stop sleeve limits the first lift, so a small volume goes in before the needle opens fully. Bosch describes that two-stage rate as a way to soften idle and part-load combustion. It is a shaped nozzle, not a common-rail pilot that an ECU can move.

A needle-motion sensor in the holder produces a signal when the needle lifts. That signal is the start of injection at the nozzle. It is not the same instant as the start of delivery inside the pump. On a distributor pump the pressure wave still has to travel the high-pressure line. Diesel injection timing and EDC15 injection systems keep those two events apart.

Why the VE pump advances delivery with speed: Bosch’s VE technical instruction explains that pump start of delivery follows inlet-port closure; pressure then builds to the nozzle-opening threshold, when the needle lifts and injection begins. Bosch calls the interval between pump delivery start and nozzle injection start “injection lag”. It describes pressure-wave travel time along the high-pressure line as essentially independent of engine speed, so the crank-angle gap between those events grows as speed rises. The VE timing device advances pump start of delivery with speed to compensate for injection and ignition lag. This is a Bosch axial-piston VE example; confirm event definitions and control behaviour for the exact pump and ECU. Bosch, Diesel distributor fuel-injection pumps VE: Technical Instruction, 4th ed. (1999), printed pp. 29–30; public PDF mirror.

In-line pumps

A standard PE in-line pump has a barrel and plunger for each cylinder. The pump's own camshaft lifts the plunger a fixed distance and a spring returns it. High pressure starts at the moment the top edge of the plunger covers the inlet port. That moment is the start of delivery. The plunger keeps rising, pressure opens the nozzle, and injection stops when a helix machined into the plunger uncovers the inlet port and the pressure collapses. The travel between those two events is the effective stroke.

A control rack rotates every plunger together. Rotating the plunger moves the helix relative to the port, so the effective stroke, and the quantity, changes. The rack is moved by a mechanical flyweight governor or by an electrical actuator. Plunger lift itself does not change. On a standard PE the start of delivery is the port closing under the plunger's top edge. It is not an independent timing lever.

The control-sleeve in-line pump adds that lever. A sleeve slides on the plunger and an actuator shaft moves it, which changes how far the plunger rises before it closes the inlet port, and therefore the start of injection. Bosch treats this as a degree of freedom the standard PE does not have: start of injection can be moved without relying on engine speed alone. Quantity is still the rack and the helix.

PF single-plunger pumps are the external-drive relation of the PE. The F in the designation is the external drive: the cams are on the engine camshaft, not in the pump, so the pump camshaft cannot be turned to set the timing. Quantity still arrives from a governor or a controller through a rack. Bosch places them on small engines, locomotives, marine engines and construction machinery. Timing, where it is adjusted, is an intermediate element or a solenoid, not a rotation of the engine camshaft.

An in-line pump with an ECU

Electronic control does not replace the helix. Bosch's PE-EDC description keeps quantity as a function of control-rack position and engine speed. A linear magnet on the pump moves the rack. With the solenoid de-energised, a spring pushes the rack to the stop and fuel delivery stops. More current moves the rack towards more fuel, and the current is a pulse-width-modulated signal, so the rack can sit anywhere between zero and full delivery. A rack-travel sensor tells the ECU where the rack actually is, and the position control corrects it.

The ECU holds a pump map. From engine speed and the desired quantity it calculates the rack travel that should produce that quantity. The control law can be given a shape taken from the mechanical RQ and RQV governors. The injector at the end of the pipe is still the spring nozzle.

On the control-sleeve pump the quantity path is the same, and a second actuator moves the sleeve. Bosch states that a low current in the start-of-delivery solenoid retards the start of delivery, and a high current advances it. A standard PE-EDC without that sleeve does not gain this second actuator just because it has an ECU. The sleeve is the hardware that makes start of delivery a separate command.

Distributor pumps

A distributor pump has one high-pressure pumping mechanism for all the cylinders. A vane supply pump fills the high-pressure chamber. An axial piston, driven by a cam plate with one lobe per cylinder, or two to four radial pistons inside a cam ring, makes the pressure. A rotating distributor opens the outlets in turn. Radial pistons can make a higher pressure than the axial piston, and the pump has to be built for it. Bosch notes that every radial-piston distributor pump in this description is solenoid-valve controlled.

On the port-and-helix VE, a control collar sets the effective stroke and therefore the quantity, whether a flyweight governor moves the collar or an electronic actuator does. The timing device rotates the roller ring and that rotation is the pump's start of delivery. In the VE-EDC arrangement a moving-magnet actuator turns the collar through a shaft, and a Hall sensor reports the angle. Return springs set delivery to zero when the actuator is de-energised. A separate timing-device solenoid is the electronic timing path. The EDC15V example of this pump is in EDC15 injection systems.

On the solenoid-valve pumps the collar is replaced by a high-pressure solenoid. While the valve is closed, pressure can build. When it opens, fuel escapes, pressure does not build, and that cylinder is not injected. The same valve therefore meters the quantity and takes part in the start of injection. The control signals come from a pump ECU, an engine ECU, or both. VP30 is the axial-piston form and VP44 the radial-piston form in Bosch's EDC15M example. A VP44 name does not say whether the controller is on the pump. VP44 and PSG16 is the pump-mounted controller that combines engine and pump functions. On the 2001 Saab 9-3 D223L the engine ECU sends a fuel mass and a timing request to the pump over a separate bus, and the pump meters and builds pressure.

Unit injectors and unit pumps

A unit injector puts the pumping element and the nozzle in one body, one per cylinder, in the head. The engine cam drives it directly or through a rocker. There is no high-pressure line between a pump and a nozzle, which is why Bosch, in 2001, could quote injection pressures up to 2,050 bar for the UIS. The ECU calculates the injection, and a high-pressure solenoid valve opens and closes to control it.

A unit pump uses the same idea and splits the hardware. The pump is driven from the engine camshaft. A short high-pressure line, matched to that pump and nozzle, joins it to a nozzle holder. Installation is easier because the pump and the holder are not one piece. Start and duration are still the solenoid.

The nozzle on both is still a pop nozzle. Bosch defines the start of delivery, the BIP (begin of injection period), as the instant the solenoid closes. Pressure then rises in the pump chamber. The nozzle opens when nozzle-opening pressure is passed, and that later instant is the start of injection. Fuel is metered in the delivery period between solenoid closure and the end of the trigger. The ECU reads the solenoid current to find the closing point, so a needle sensor is not required. If that BIP signal fails, Bosch describes a change to open-loop control. One unwanted injection is the failure Bosch treats these systems as able to limit themselves to, because an open solenoid spills the pressure.

Volkswagen's pumped-nozzle engines and the commercial-vehicle unit pumps are this family, not a common rail. Pressures, the Volkswagen applications and the large-engine unit are on diesel unit-injector systems. The EDC16 V10 and V6 contrast is in EDC16 torque and fuel.

Common rail is a different pump

A common-rail supply pump does not meter the cylinder's fuel with a helix or a collar. It keeps a rail at a commanded pressure, and the injector, opened electrically, decides the moment and the duration. Injection pressure can stay high at low speed, which is where a distributor pump is weakest, and more than one injection per stroke is normal. The pumps, the pressures and the four manufacturers' hardware are already set out in common-rail diesel fuel systems and common-rail supply pumps. The injector is not a shimmed pop holder: common-rail diesel injectors.

Sources