Removed text is struck through; added text is highlighted.
A common-rail diesel keeps fuel at injection pressure in a shared rail, then lets the engine controller decide, for each cylinder, when the injector opens and for how long. The pump still produces pressure pulses, but the rail stores and damps them; injection timing and quantity are controlled independently of individual pump strokes. The same rail feeds every injector, so a leak at one injector, or a pump that cannot keep up, shows up as rail pressure for the whole engine.
The hardware splits into a low-pressure supply, a mechanically driven high-pressure pump, the rail, and the injectors. The controller closes the loop on a rail-pressure sensor. Pump types and their pressures are on common-rail supply pumps. Injector construction and coding are on common-rail diesel injectors. The tests are on common-rail fuel system tests. A hydraulic unit injector, which uses engine oil rather than a fuel rail to make injection pressure, is a different system: HEUI fuel systems.
Original illustration for Tuning Wiki. Blue shows the feed side, red the high-pressure side and grey a simplified injector return; actual system layouts vary.
What changed from the distributor pump
On a mechanical in-line pump or a distributor pump, injection pressure depends on engine speed, and the maximum pressure is limited by the pump itself. Pilot injection, and more than one injection in a stroke, are difficult. An electronically controlled distributor, the ECD-V series, added an electromagnetic spill valve so each cylinder’s quantity could be trimmed, and later versions added an inner-cam pump and pilot injection. The published maxima for that family step through 60 MPa, 100 MPa and 130 MPa. 1 MPa is 10 bar.
A common rail stores the pressure. The supply pump keeps the rail charged. The injector, not the pump cam, decides the moment of injection. Injection pressure can stay high at low engine speed, which is where a distributor pump is weakest, and the controller can fire a small pilot before the main injection. Higher-pressure atomisation and suitable electronic control can reduce smoke, but the outcome depends on the whole engine and calibration. Bosch: common-rail operation.
Original chart for Tuning Wiki using Denso pump-family data. Maximum capability is not a vehicle operating or test target.Original chart of published family maxima. Idle pressure is much lower than these figures. A later comparison also marks 145 MPa and 185 MPa without tying either mark to a single pump.
The systems in use
Bosch, Denso (earlier Nippondenso), Delphi and Siemens are among the manufacturers of production common-rail equipment. Denso’s commercial truck system dates from 1995. The passenger-car pump, the HP2, followed in 1999, the lighter HP3 in 2001, and the three-plunger HP4 in 2004. Bosch, Siemens and Delphi each sold their own pumps, rails and injectors. The parts do not interchange, and a return-quantity limit written for one injector will condemn a good injector of another make.
SystemHow rail pressure is setInjectorController, where this wiki has one
BoschEarly pumps spill from the high-pressure side. Later pumps meter the fuel taken into the pumping elements. CP1H and CP3 use a gear feed pump and run the inlet under a slight vacuum.Solenoid or piezo, depending on the system. Some Bosch piezo installations require a pressurised return; use the vehicle-specific specification.EDC15 common-rail variants, EDC16, EDC17, MD1. Controller suffixes alone do not establish a particular vehicle's fuel-system layout; some EDC16 applications use unit injectors.
DensoHP0 meters with a pump control valve on the plunger’s pre-stroke. HP2, HP3 and HP4 meter with a suction control valve, so the pump only compresses the volume the rail needs.Solenoid two-way valve. Generations X1, X2 and G2. Later injectors carry a QR code instead of a correction resistor.A Denso engine ECU. Many applications add an EDU, a separate high-voltage injector driver. Some ECUs contain that charge circuit and have no EDU.
DelphiIts own high-pressure pump and rail hardware. Low-pressure and return figures have to be taken from that system’s procedure.Solenoid injectors trimmed by a C2i code written into the controller for the cylinder the injector is fitted to.Delphi diesel controllers. Treat a C2i code as injector calibration, not as a tune.
SiemensIts own pump and rail. The injector return must stay at the pressure that injector was designed for.Piezo stack. Opening and closing are opposite polarities. Families include 5WS40000 and 5WS40148 / 5WS40149.Siemens diesel controllers, later associated with Continental. Do not use the petrol Siemens MS and Simos pages for these injectors.SystemHow rail pressure is setInjectorController, where this wiki has one
BoschEarly pumps spill from the high-pressure side. Later pumps meter the fuel taken into the pumping elements. CP1H and CP3 use a gear feed pump and run the inlet under a slight vacuum.Solenoid or piezo, depending on the system. Some Bosch piezo installations require a pressurised return; use the vehicle-specific specification.EDC15 common-rail variants, EDC16, EDC17, MD1. The C and CP suffixes are the common-rail branches. Unit-injector EDC16s are a different fuel system.
DensoHP0 meters with a pump control valve on the plunger’s pre-stroke. HP2, HP3 and HP4 meter with a suction control valve, so the pump only compresses the volume the rail needs.Solenoid two-way valve. Generations X1, X2 and G2. Later injectors carry a QR code instead of a correction resistor.A Denso engine ECU. Many applications add an EDU, a separate high-voltage injector driver. Some ECUs contain that charge circuit and have no EDU.
DelphiIts own high-pressure pump and rail hardware. Low-pressure and return figures have to be taken from that system’s procedure.Solenoid injectors trimmed by a C2i code written into the controller for the cylinder the injector is fitted to.Delphi diesel controllers. Treat a C2i code as injector calibration, not as a tune.
SiemensIts own pump and rail. The injector return must stay at the pressure that injector was designed for.Piezo stack. Opening and closing are opposite polarities. Families include 5WS40000 and 5WS40148 / 5WS40149.Siemens diesel controllers, later associated with Continental. Do not use the petrol Siemens MS and Simos pages for these injectors.
Bosch’s own vehicle examples already on this wiki are narrower than the family labels. The Volkswagen 3.0 V6 TDI case on EDC16 injection systems is an EDC 16 C common rail with a high-pressure range of 300 to 1,600 bar, piezo injectors, a pressure sender, a pressure-regulating valve and a fuel-metering valve, and a 10 bar injector return. The Audi 2.7 TDI example there is an EDC-16CP+ system with a stated maximum of 1,600 bar. Those figures belong to those installations. EDC17 Audi 2.0 TDI is the later Bosch controller on a different engine.
What the controller commands
The engine ECU reads crankshaft speed, cylinder recognition, accelerator position, temperatures, intake pressure and, where fitted, air mass. It then commands three things that used to be mechanical: rail pressure, injection timing and injection quantity. Because those three are independent of a pump cam, several injections in one stroke are normal.
Pilot injection puts a small quantity in before the main. High pressure would otherwise put too much fuel in during the ignition delay, and that fuel would burn at once. The result of that burn is diesel knock and NOx. The pilot shortens the delay and cuts the noise.
Split injection on a cold start breaks the early fuel into two or more very small pulses before the main, to help the engine light.
Multi-injection can add small pulses before and after the main injection. The number, timing and total fuel quantity depend on the operating and emissions strategy. A five-pulse pattern is pre-injection, pilot, main, after-injection and post-injection.
In an example Denso control strategy, quantity is the lesser of two calculations; other controllers and operating modes may use different models and limits. One is the governor quantity, from accelerator position and engine speed: more pedal gives more fuel, and at a fixed pedal a rising engine speed gives less. The other is the maximum quantity, from engine speed, reduced or increased for coolant temperature, fuel temperature, intake temperature, intake pressure, atmospheric pressure and, on a first-generation HP0 only, a selected full-load resistor. There are 15 of those resistors. The manufacturer fits the one that brings that pump to the full-load standard. During acceleration a large pedal change is delayed on purpose, so the fuel does not arrive before the air and make black smoke. Starting quantity is a separate map, increased when the coolant is cold, and it is cancelled once the engine has started.
In that example, main timing starts from engine speed and the final quantity, then moves for battery voltage, intake pressure, atmospheric pressure, intake temperature and coolant temperature. Pilot timing is a calculated interval before that main pulse. The interval during cranking comes from coolant temperature and speed. Rail-pressure demand comes from the final quantity and engine speed once the engine is running, and from coolant temperature and speed while it is starting.
In these diesel examples the ECU controls idle speed primarily by adjusting fuel quantity. The target depends on coolant temperature, whether the transmission is automatic, the gear position and the air-conditioning load. Some installations still have a manual idle setting. A separate idle-balance function compares the angular time of each cylinder and trims that cylinder’s quantity when one is slow. That trim is a symptom. It is not, by itself, proof that the injector is the failed part. Low compression and a valve that does not seal move the same number. See EDC15 diagnostic data for the earlier form of the comparison, and fuelling faults for how to read it.
Operating pressures
A number is only useful with the condition it was measured under. These are the published bands, not a target to tune to.
ConditionPressureWhat it belongs to
Cranking and startingVehicle- and test-specificStarting pressure is not universal. One Delphi guide for certain 2.0 HDi vehicles specifies 117 bar; use the exact vehicle procedure. A pump-outlet capacity test and an installed rail-pressure threshold are different measurements. Delphi: scoped starting example.
Idle and light loadOften a few hundred bar. One Toyota running-engine monitor expects the displayed value, after a warm-up, to lie between 30 and 160 MPa (300 to 1,600 bar).That span is the normal running band of that monitor. It is not an idle setpoint.
Full load, passenger-car systems of the 1,600 bar generationAbout 1,600 bar (160 MPa)The general full-load figure, and the top of the Volkswagen 3.0 V6 and Audi 2.7 examples.
Denso HP3 and HP4 examplesHP3: originally 180 MPa; later versions up to 200 MPa. HP4: up to 200 MPa.These are family capability examples, not a pressure target for an individual engine. Denso: common-rail pumps.
Later systemsUp to 2,700 bar on a Bosch piezo systemSystem capability varies. Pressure may remain after shutdown; follow the exact depressurisation procedure. Bosch: piezo common rail.
Pressure limiterDesign- and vehicle-specificOpening and reset behaviour vary; follow the specified test procedure.
Low-pressure supplySystem-specific positive pressure or suctionMeasure at the prescribed point and conditions using approved equipment. Delphi: feed pressure and restriction.
Injector returnSystem-specificSome systems require maintained return back-pressure. Use the prescribed adapter and test; see Pico: return test restrictions.ConditionPressureWhat it belongs to
Cranking and startingVehicle- and test-specificStarting pressure is not universal. One Delphi guide for certain 2.0 HDi vehicles specifies 117 bar; use the exact vehicle procedure. A pump-outlet capacity test and an installed rail-pressure threshold are different measurements. Delphi: scoped starting example.
Idle and light loadOften a few hundred bar. One Toyota running-engine monitor expects the displayed value, after a warm-up, to lie between 30 and 160 MPa (300 to 1,600 bar).That span is the normal running band of that monitor. It is not an idle setpoint.
Full load, passenger-car systems of the 1,600 bar generationAbout 1,600 bar (160 MPa)The general full-load figure, and the top of the Volkswagen 3.0 V6 and Audi 2.7 examples.
Second-generation Denso (HP3, HP4) maximum180 MPa (1,800 bar)Family maximum injection pressure.
Later systemsUp to 2,700 bar on a Bosch piezo systemSystem capability varies. Pressure may remain after shutdown; follow the exact depressurisation procedure. Bosch: piezo common rail.
Cummins common rail, injectors enabledAbout 5,000 psi (345 bar) before the injectors are fired. Idle about 5,000 psi. Wide-open throttle up to about 30,000 psi (about 2,070 bar).That cranking threshold is why a leak that empties the rail stretches a normal three-to-five-second start. It is this system’s threshold, not a Bosch passenger-car start map.
Pressure limiter, railOpens at about 140 to 230 MPa and reseats at about 30 to 50 MPaThe exact pair depends on the vehicle. Fuel from the limiter returns to the tank.
Low-pressure supplyElectric feed pump 2.0 to 2.5 bar while cranking. Gear feed pump on CP1H and CP3: a suction of 0.10 to 0.20 bar. A filter pressure-drop limit depends on the vehicle and test conditions.Measured with a low-pressure gauge. A high-pressure gauge does not belong on this pipe, and a petrol gauge does not belong on the rail.
Injector return0.6 to 0.9 bar on a first-generation Bosch system, measured between the collector and the tank. About 10 bar on a third-generation Bosch piezo system.The first figure is what opens the pump safety valve. The 10 bar figure is required for the piezo injector to operate. Holding it needs the adaptor made for that return.
Rail, limiter and sensors
The rail is a store. Its shape changes with the engine, but the parts are the same kinds of part: a pressure sensor, a pressure limiter, and on some engines a flow damper or a pressure-discharge valve.
The limiter is a mechanical relief. If rail pressure runs away it opens and dumps fuel to the tank, then shuts again once the pressure has fallen. The sensor is a semiconductor element on a 5 V supply. Some rails have two sensing elements with offset outputs, so a single failed element can be detected. The ECU closes the pressure loop on this signal. A sensor that reads low will drive the pump harder. If approved for the vehicle, a specialist can compare a correctly rated reference measurement with ECU data. A discrepancy also requires checking the reference instrument, sensor supply, ground and signal wiring before deciding which component is faulty.
A flow damper sits in the pipe to an injector, mostly on larger engines. A normal pressure pulse moves its piston and the piston returns. An abnormal flow, from a split pipe or an injector that is pouring fuel, drives the piston onto its seat and shuts that pipe off. The leak then stops, which is easy to misread as a pipe that was never leaking. Passenger-car rails more often use a solenoid pressure-discharge valve: the ECU opens it when rail pressure is above the target and the fuel returns to the tank.
On an HP0 the cylinder-recognition sensor is on the pump camshaft. On HP2, HP3 and HP4 it is by the pump timing gear. Combined with the crankshaft sensor it tells the ECU which cylinder is which. Those historical Denso examples use particular sensor designs. Crank sensors may be inductive or Hall-effect; sensor location and fallback behaviour vary by engine. Loss of a timing signal can cause a no-start, stall or degraded running, but does not always stop injection immediately. Bosch: crank sensor types; Pico: cam sensor faults.
Fuel, cleanliness and injury
The pumping elements and the injector clearances are lubricated by the fuel. Petrol in a diesel tank destroys that lubrication. Water in the sedimentor does the same, more slowly. A blocked filter, or a gauze screen full of debris, starves the high-pressure pump and the pump is then blamed. Dirt that enters an opened joint is enough to ruin a pump and a set of injectors. Open the system only after it has been depressurised, cap every port, and do not reuse a suspect high-pressure pipe.
Rail pressure will inject through skin. Follow the vehicle manufacturer's depressurisation and isolation procedure before opening a joint; elapsed time alone does not prove the pressure is safe. Do not use a cap, a plug or a finger as a substitute for the blanking tool made for a high-pressure port.
Petrol direct injection is a rail as well
A petrol direct-injection engine has the same split, at much lower pressure. An in-tank pump feeds a cam-driven high-pressure pump, and that pump feeds a rail and the injectors in the head. Current Bosch systems are described at up to 6 bar into the high-pressure pump and up to 350 bar in the rail. The low-pressure side is often returnless: the pump can be driven with a pulsed supply; a meter may display an average or varying reading depending on its settings and the control signal. Use the specified test equipment and method. Loss of communication with the pump module can shut the pump off even though the pump itself is sound. The failure modes and the tests are on fuel pump faults and the test page.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 4: Common-rail diesel fuel systems
A common-rail diesel keeps fuel at injection pressure in a shared rail, then lets the engine controller decide, for each cylinder, when the injector opens and for how long. The pump still produces pressure pulses, but the rail stores and damps them; injection timing and quantity are controlled independently of individual pump strokes. The same rail feeds every injector, so a leak at one injector, or a pump that cannot keep up, shows up as rail pressure for the whole engine.
The hardware splits into a low-pressure supply, a mechanically driven high-pressure pump, the rail, and the injectors. The controller closes the loop on a rail-pressure sensor. Pump types and their pressures are on common-rail supply pumps. Injector construction and coding are on common-rail diesel injectors. The tests are on common-rail fuel system tests. A hydraulic unit injector, which uses engine oil rather than a fuel rail to make injection pressure, is a different system: HEUI fuel systems.
Original illustration for Tuning Wiki. Blue shows the feed side, red the high-pressure side and grey a simplified injector return; actual system layouts vary.
What changed from the distributor pump
On a mechanical in-line pump or a distributor pump, injection pressure depends on engine speed, and the maximum pressure is limited by the pump itself. Pilot injection, and more than one injection in a stroke, are difficult. An electronically controlled distributor, the ECD-V series, added an electromagnetic spill valve so each cylinder’s quantity could be trimmed, and later versions added an inner-cam pump and pilot injection. The published maxima for that family step through 60 MPa, 100 MPa and 130 MPa. 1 MPa is 10 bar.
A common rail stores the pressure. The supply pump keeps the rail charged. The injector, not the pump cam, decides the moment of injection. Injection pressure can stay high at low engine speed, which is where a distributor pump is weakest, and the controller can fire a small pilot before the main injection. Higher-pressure atomisation and suitable electronic control can reduce smoke, but the outcome depends on the whole engine and calibration. Bosch: common-rail operation.
Original chart of published family maxima. Idle pressure is much lower than these figures. A later comparison also marks 145 MPa and 185 MPa without tying either mark to a single pump.
The systems in use
Bosch, Denso (earlier Nippondenso), Delphi and Siemens are among the manufacturers of production common-rail equipment. Denso’s commercial truck system dates from 1995. The passenger-car pump, the HP2, followed in 1999, the lighter HP3 in 2001, and the three-plunger HP4 in 2004. Bosch, Siemens and Delphi each sold their own pumps, rails and injectors. The parts do not interchange, and a return-quantity limit written for one injector will condemn a good injector of another make.
System
How rail pressure is set
Injector
Controller, where this wiki has one
Bosch
Early pumps spill from the high-pressure side. Later pumps meter the fuel taken into the pumping elements. CP1H and CP3 use a gear feed pump and run the inlet under a slight vacuum.
Solenoid or piezo, depending on the system. Some Bosch piezo installations require a pressurised return; use the vehicle-specific specification.
EDC15 common-rail variants, EDC16, EDC17, MD1. The C and CP suffixes are the common-rail branches. Unit-injector EDC16s are a different fuel system.
Denso
HP0 meters with a pump control valve on the plunger’s pre-stroke. HP2, HP3 and HP4 meter with a suction control valve, so the pump only compresses the volume the rail needs.
Solenoid two-way valve. Generations X1, X2 and G2. Later injectors carry a QR code instead of a correction resistor.
A Denso engine ECU. Many applications add an EDU, a separate high-voltage injector driver. Some ECUs contain that charge circuit and have no EDU.
Delphi
Its own high-pressure pump and rail hardware. Low-pressure and return figures have to be taken from that system’s procedure.
Solenoid injectors trimmed by a C2i code written into the controller for the cylinder the injector is fitted to.
Delphi diesel controllers. Treat a C2i code as injector calibration, not as a tune.
Siemens
Its own pump and rail. The injector return must stay at the pressure that injector was designed for.
Piezo stack. Opening and closing are opposite polarities. Families include 5WS40000 and 5WS40148 / 5WS40149.
Siemens diesel controllers, later associated with Continental. Do not use the petrol Siemens MS and Simos pages for these injectors.
Bosch’s own vehicle examples already on this wiki are narrower than the family labels. The Volkswagen 3.0 V6 TDI case on EDC16 injection systems is an EDC 16 C common rail with a high-pressure range of 300 to 1,600 bar, piezo injectors, a pressure sender, a pressure-regulating valve and a fuel-metering valve, and a 10 bar injector return. The Audi 2.7 TDI example there is an EDC-16CP+ system with a stated maximum of 1,600 bar. Those figures belong to those installations. EDC17 Audi 2.0 TDI is the later Bosch controller on a different engine.
What the controller commands
The engine ECU reads crankshaft speed, cylinder recognition, accelerator position, temperatures, intake pressure and, where fitted, air mass. It then commands three things that used to be mechanical: rail pressure, injection timing and injection quantity. Because those three are independent of a pump cam, several injections in one stroke are normal.
Pilot injection puts a small quantity in before the main. High pressure would otherwise put too much fuel in during the ignition delay, and that fuel would burn at once. The result of that burn is diesel knock and NOx. The pilot shortens the delay and cuts the noise.
Split injection on a cold start breaks the early fuel into two or more very small pulses before the main, to help the engine light.
Multi-injection can add small pulses before and after the main injection. The number, timing and total fuel quantity depend on the operating and emissions strategy. A five-pulse pattern is pre-injection, pilot, main, after-injection and post-injection.
In an example Denso control strategy, quantity is the lesser of two calculations; other controllers and operating modes may use different models and limits. One is the governor quantity, from accelerator position and engine speed: more pedal gives more fuel, and at a fixed pedal a rising engine speed gives less. The other is the maximum quantity, from engine speed, reduced or increased for coolant temperature, fuel temperature, intake temperature, intake pressure, atmospheric pressure and, on a first-generation HP0 only, a selected full-load resistor. There are 15 of those resistors. The manufacturer fits the one that brings that pump to the full-load standard. During acceleration a large pedal change is delayed on purpose, so the fuel does not arrive before the air and make black smoke. Starting quantity is a separate map, increased when the coolant is cold, and it is cancelled once the engine has started.
In that example, main timing starts from engine speed and the final quantity, then moves for battery voltage, intake pressure, atmospheric pressure, intake temperature and coolant temperature. Pilot timing is a calculated interval before that main pulse. The interval during cranking comes from coolant temperature and speed. Rail-pressure demand comes from the final quantity and engine speed once the engine is running, and from coolant temperature and speed while it is starting.
In these diesel examples the ECU controls idle speed primarily by adjusting fuel quantity. The target depends on coolant temperature, whether the transmission is automatic, the gear position and the air-conditioning load. Some installations still have a manual idle setting. A separate idle-balance function compares the angular time of each cylinder and trims that cylinder’s quantity when one is slow. That trim is a symptom. It is not, by itself, proof that the injector is the failed part. Low compression and a valve that does not seal move the same number. See EDC15 diagnostic data for the earlier form of the comparison, and fuelling faults for how to read it.
Operating pressures
A number is only useful with the condition it was measured under. These are the published bands, not a target to tune to.
Condition
Pressure
What it belongs to
Cranking and starting
Vehicle- and test-specific
Starting pressure is not universal. One Delphi guide for certain 2.0 HDi vehicles specifies 117 bar; use the exact vehicle procedure. A pump-outlet capacity test and an installed rail-pressure threshold are different measurements. Delphi: scoped starting example.
Idle and light load
Often a few hundred bar. One Toyota running-engine monitor expects the displayed value, after a warm-up, to lie between 30 and 160 MPa (300 to 1,600 bar).
That span is the normal running band of that monitor. It is not an idle setpoint.
Full load, passenger-car systems of the 1,600 bar generation
About 1,600 bar (160 MPa)
The general full-load figure, and the top of the Volkswagen 3.0 V6 and Audi 2.7 examples.
Second-generation Denso (HP3, HP4) maximum
180 MPa (1,800 bar)
Family maximum injection pressure.
Later systems
Up to 2,700 bar on a Bosch piezo system
System capability varies. Pressure may remain after shutdown; follow the exact depressurisation procedure. Bosch: piezo common rail.
Cummins common rail, injectors enabled
About 5,000 psi (345 bar) before the injectors are fired. Idle about 5,000 psi. Wide-open throttle up to about 30,000 psi (about 2,070 bar).
That cranking threshold is why a leak that empties the rail stretches a normal three-to-five-second start. It is this system’s threshold, not a Bosch passenger-car start map.
Pressure limiter, rail
Opens at about 140 to 230 MPa and reseats at about 30 to 50 MPa
The exact pair depends on the vehicle. Fuel from the limiter returns to the tank.
Low-pressure supply
Electric feed pump 2.0 to 2.5 bar while cranking. Gear feed pump on CP1H and CP3: a suction of 0.10 to 0.20 bar. A filter pressure-drop limit depends on the vehicle and test conditions.
Measured with a low-pressure gauge. A high-pressure gauge does not belong on this pipe, and a petrol gauge does not belong on the rail.
Injector return
0.6 to 0.9 bar on a first-generation Bosch system, measured between the collector and the tank. About 10 bar on a third-generation Bosch piezo system.
The first figure is what opens the pump safety valve. The 10 bar figure is required for the piezo injector to operate. Holding it needs the adaptor made for that return.
Rail, limiter and sensors
The rail is a store. Its shape changes with the engine, but the parts are the same kinds of part: a pressure sensor, a pressure limiter, and on some engines a flow damper or a pressure-discharge valve.
The limiter is a mechanical relief. If rail pressure runs away it opens and dumps fuel to the tank, then shuts again once the pressure has fallen. The sensor is a semiconductor element on a 5 V supply. Some rails have two sensing elements with offset outputs, so a single failed element can be detected. The ECU closes the pressure loop on this signal. A sensor that reads low will drive the pump harder. If approved for the vehicle, a specialist can compare a correctly rated reference measurement with ECU data. A discrepancy also requires checking the reference instrument, sensor supply, ground and signal wiring before deciding which component is faulty.
A flow damper sits in the pipe to an injector, mostly on larger engines. A normal pressure pulse moves its piston and the piston returns. An abnormal flow, from a split pipe or an injector that is pouring fuel, drives the piston onto its seat and shuts that pipe off. The leak then stops, which is easy to misread as a pipe that was never leaking. Passenger-car rails more often use a solenoid pressure-discharge valve: the ECU opens it when rail pressure is above the target and the fuel returns to the tank.
On an HP0 the cylinder-recognition sensor is on the pump camshaft. On HP2, HP3 and HP4 it is by the pump timing gear. Combined with the crankshaft sensor it tells the ECU which cylinder is which. Those historical Denso examples use particular sensor designs. Crank sensors may be inductive or Hall-effect; sensor location and fallback behaviour vary by engine. Loss of a timing signal can cause a no-start, stall or degraded running, but does not always stop injection immediately. Bosch: crank sensor types; Pico: cam sensor faults.
Fuel, cleanliness and injury
The pumping elements and the injector clearances are lubricated by the fuel. Petrol in a diesel tank destroys that lubrication. Water in the sedimentor does the same, more slowly. A blocked filter, or a gauze screen full of debris, starves the high-pressure pump and the pump is then blamed. Dirt that enters an opened joint is enough to ruin a pump and a set of injectors. Open the system only after it has been depressurised, cap every port, and do not reuse a suspect high-pressure pipe.
Rail pressure will inject through skin. Follow the vehicle manufacturer's depressurisation and isolation procedure before opening a joint; elapsed time alone does not prove the pressure is safe. Do not use a cap, a plug or a finger as a substitute for the blanking tool made for a high-pressure port.
Petrol direct injection is a rail as well
A petrol direct-injection engine has the same split, at much lower pressure. An in-tank pump feeds a cam-driven high-pressure pump, and that pump feeds a rail and the injectors in the head. Current Bosch systems are described at up to 6 bar into the high-pressure pump and up to 350 bar in the rail. The low-pressure side is often returnless: the pump can be driven with a pulsed supply; a meter may display an average or varying reading depending on its settings and the control signal. Use the specified test equipment and method. Loss of communication with the pump module can shut the pump off even though the pump itself is sound. The failure modes and the tests are on fuel pump faults and the test page.
Revision 6: Common-rail diesel fuel systems
A common-rail diesel keeps fuel at injection pressure in a shared rail, then lets the engine controller decide, for each cylinder, when the injector opens and for how long. The pump still produces pressure pulses, but the rail stores and damps them; injection timing and quantity are controlled independently of individual pump strokes. The same rail feeds every injector, so a leak at one injector, or a pump that cannot keep up, shows up as rail pressure for the whole engine.
The hardware splits into a low-pressure supply, a mechanically driven high-pressure pump, the rail, and the injectors. The controller closes the loop on a rail-pressure sensor. Pump types and their pressures are on common-rail supply pumps. Injector construction and coding are on common-rail diesel injectors. The tests are on common-rail fuel system tests. A hydraulic unit injector, which uses engine oil rather than a fuel rail to make injection pressure, is a different system: HEUI fuel systems.
Original illustration for Tuning Wiki. Blue shows the feed side, red the high-pressure side and grey a simplified injector return; actual system layouts vary.
What changed from the distributor pump
On a mechanical in-line pump or a distributor pump, injection pressure depends on engine speed, and the maximum pressure is limited by the pump itself. Pilot injection, and more than one injection in a stroke, are difficult. An electronically controlled distributor, the ECD-V series, added an electromagnetic spill valve so each cylinder’s quantity could be trimmed, and later versions added an inner-cam pump and pilot injection. The published maxima for that family step through 60 MPa, 100 MPa and 130 MPa. 1 MPa is 10 bar.
A common rail stores the pressure. The supply pump keeps the rail charged. The injector, not the pump cam, decides the moment of injection. Injection pressure can stay high at low engine speed, which is where a distributor pump is weakest, and the controller can fire a small pilot before the main injection. Higher-pressure atomisation and suitable electronic control can reduce smoke, but the outcome depends on the whole engine and calibration. Bosch: common-rail operation.
Original chart for Tuning Wiki using Denso pump-family data. Maximum capability is not a vehicle operating or test target.
The systems in use
Bosch, Denso (earlier Nippondenso), Delphi and Siemens are among the manufacturers of production common-rail equipment. Denso’s commercial truck system dates from 1995. The passenger-car pump, the HP2, followed in 1999, the lighter HP3 in 2001, and the three-plunger HP4 in 2004. Bosch, Siemens and Delphi each sold their own pumps, rails and injectors. The parts do not interchange, and a return-quantity limit written for one injector will condemn a good injector of another make.
System
How rail pressure is set
Injector
Controller, where this wiki has one
Bosch
Early pumps spill from the high-pressure side. Later pumps meter the fuel taken into the pumping elements. CP1H and CP3 use a gear feed pump and run the inlet under a slight vacuum.
Solenoid or piezo, depending on the system. Some Bosch piezo installations require a pressurised return; use the vehicle-specific specification.
EDC15 common-rail variants, EDC16, EDC17, MD1. Controller suffixes alone do not establish a particular vehicle's fuel-system layout; some EDC16 applications use unit injectors.
Denso
HP0 meters with a pump control valve on the plunger’s pre-stroke. HP2, HP3 and HP4 meter with a suction control valve, so the pump only compresses the volume the rail needs.
Solenoid two-way valve. Generations X1, X2 and G2. Later injectors carry a QR code instead of a correction resistor.
A Denso engine ECU. Many applications add an EDU, a separate high-voltage injector driver. Some ECUs contain that charge circuit and have no EDU.
Delphi
Its own high-pressure pump and rail hardware. Low-pressure and return figures have to be taken from that system’s procedure.
Solenoid injectors trimmed by a C2i code written into the controller for the cylinder the injector is fitted to.
Delphi diesel controllers. Treat a C2i code as injector calibration, not as a tune.
Siemens
Its own pump and rail. The injector return must stay at the pressure that injector was designed for.
Piezo stack. Opening and closing are opposite polarities. Families include 5WS40000 and 5WS40148 / 5WS40149.
Siemens diesel controllers, later associated with Continental. Do not use the petrol Siemens MS and Simos pages for these injectors.
Bosch’s own vehicle examples already on this wiki are narrower than the family labels. The Volkswagen 3.0 V6 TDI case on EDC16 injection systems is an EDC 16 C common rail with a high-pressure range of 300 to 1,600 bar, piezo injectors, a pressure sender, a pressure-regulating valve and a fuel-metering valve, and a 10 bar injector return. The Audi 2.7 TDI example there is an EDC-16CP+ system with a stated maximum of 1,600 bar. Those figures belong to those installations. EDC17 Audi 2.0 TDI is the later Bosch controller on a different engine.
What the controller commands
The engine ECU reads crankshaft speed, cylinder recognition, accelerator position, temperatures, intake pressure and, where fitted, air mass. It then commands three things that used to be mechanical: rail pressure, injection timing and injection quantity. Because those three are independent of a pump cam, several injections in one stroke are normal.
Pilot injection puts a small quantity in before the main. High pressure would otherwise put too much fuel in during the ignition delay, and that fuel would burn at once. The result of that burn is diesel knock and NOx. The pilot shortens the delay and cuts the noise.
Split injection on a cold start breaks the early fuel into two or more very small pulses before the main, to help the engine light.
Multi-injection can add small pulses before and after the main injection. The number, timing and total fuel quantity depend on the operating and emissions strategy. A five-pulse pattern is pre-injection, pilot, main, after-injection and post-injection.
In an example Denso control strategy, quantity is the lesser of two calculations; other controllers and operating modes may use different models and limits. One is the governor quantity, from accelerator position and engine speed: more pedal gives more fuel, and at a fixed pedal a rising engine speed gives less. The other is the maximum quantity, from engine speed, reduced or increased for coolant temperature, fuel temperature, intake temperature, intake pressure, atmospheric pressure and, on a first-generation HP0 only, a selected full-load resistor. There are 15 of those resistors. The manufacturer fits the one that brings that pump to the full-load standard. During acceleration a large pedal change is delayed on purpose, so the fuel does not arrive before the air and make black smoke. Starting quantity is a separate map, increased when the coolant is cold, and it is cancelled once the engine has started.
In that example, main timing starts from engine speed and the final quantity, then moves for battery voltage, intake pressure, atmospheric pressure, intake temperature and coolant temperature. Pilot timing is a calculated interval before that main pulse. The interval during cranking comes from coolant temperature and speed. Rail-pressure demand comes from the final quantity and engine speed once the engine is running, and from coolant temperature and speed while it is starting.
In these diesel examples the ECU controls idle speed primarily by adjusting fuel quantity. The target depends on coolant temperature, whether the transmission is automatic, the gear position and the air-conditioning load. Some installations still have a manual idle setting. A separate idle-balance function compares the angular time of each cylinder and trims that cylinder’s quantity when one is slow. That trim is a symptom. It is not, by itself, proof that the injector is the failed part. Low compression and a valve that does not seal move the same number. See EDC15 diagnostic data for the earlier form of the comparison, and fuelling faults for how to read it.
Operating pressures
A number is only useful with the condition it was measured under. These are the published bands, not a target to tune to.
Condition
Pressure
What it belongs to
Cranking and starting
Vehicle- and test-specific
Starting pressure is not universal. One Delphi guide for certain 2.0 HDi vehicles specifies 117 bar; use the exact vehicle procedure. A pump-outlet capacity test and an installed rail-pressure threshold are different measurements. Delphi: scoped starting example.
Idle and light load
Often a few hundred bar. One Toyota running-engine monitor expects the displayed value, after a warm-up, to lie between 30 and 160 MPa (300 to 1,600 bar).
That span is the normal running band of that monitor. It is not an idle setpoint.
Full load, passenger-car systems of the 1,600 bar generation
About 1,600 bar (160 MPa)
The general full-load figure, and the top of the Volkswagen 3.0 V6 and Audi 2.7 examples.
Denso HP3 and HP4 examples
HP3: originally 180 MPa; later versions up to 200 MPa. HP4: up to 200 MPa.
These are family capability examples, not a pressure target for an individual engine. Denso: common-rail pumps.
Later systems
Up to 2,700 bar on a Bosch piezo system
System capability varies. Pressure may remain after shutdown; follow the exact depressurisation procedure. Bosch: piezo common rail.
Pressure limiter
Design- and vehicle-specific
Opening and reset behaviour vary; follow the specified test procedure.
Some systems require maintained return back-pressure. Use the prescribed adapter and test; see Pico: return test restrictions.
Rail, limiter and sensors
The rail is a store. Its shape changes with the engine, but the parts are the same kinds of part: a pressure sensor, a pressure limiter, and on some engines a flow damper or a pressure-discharge valve.
The limiter is a mechanical relief. If rail pressure runs away it opens and dumps fuel to the tank, then shuts again once the pressure has fallen. The sensor is a semiconductor element on a 5 V supply. Some rails have two sensing elements with offset outputs, so a single failed element can be detected. The ECU closes the pressure loop on this signal. A sensor that reads low will drive the pump harder. If approved for the vehicle, a specialist can compare a correctly rated reference measurement with ECU data. A discrepancy also requires checking the reference instrument, sensor supply, ground and signal wiring before deciding which component is faulty.
A flow damper sits in the pipe to an injector, mostly on larger engines. A normal pressure pulse moves its piston and the piston returns. An abnormal flow, from a split pipe or an injector that is pouring fuel, drives the piston onto its seat and shuts that pipe off. The leak then stops, which is easy to misread as a pipe that was never leaking. Passenger-car rails more often use a solenoid pressure-discharge valve: the ECU opens it when rail pressure is above the target and the fuel returns to the tank.
On an HP0 the cylinder-recognition sensor is on the pump camshaft. On HP2, HP3 and HP4 it is by the pump timing gear. Combined with the crankshaft sensor it tells the ECU which cylinder is which. Those historical Denso examples use particular sensor designs. Crank sensors may be inductive or Hall-effect; sensor location and fallback behaviour vary by engine. Loss of a timing signal can cause a no-start, stall or degraded running, but does not always stop injection immediately. Bosch: crank sensor types; Pico: cam sensor faults.
Fuel, cleanliness and injury
The pumping elements and the injector clearances are lubricated by the fuel. Petrol in a diesel tank destroys that lubrication. Water in the sedimentor does the same, more slowly. A blocked filter, or a gauze screen full of debris, starves the high-pressure pump and the pump is then blamed. Dirt that enters an opened joint is enough to ruin a pump and a set of injectors. Open the system only after it has been depressurised, cap every port, and do not reuse a suspect high-pressure pipe.
Rail pressure will inject through skin. Follow the vehicle manufacturer's depressurisation and isolation procedure before opening a joint; elapsed time alone does not prove the pressure is safe. Do not use a cap, a plug or a finger as a substitute for the blanking tool made for a high-pressure port.
Petrol direct injection is a rail as well
A petrol direct-injection engine has the same split, at much lower pressure. An in-tank pump feeds a cam-driven high-pressure pump, and that pump feeds a rail and the injectors in the head. Current Bosch systems are described at up to 6 bar into the high-pressure pump and up to 350 bar in the rail. The low-pressure side is often returnless: the pump can be driven with a pulsed supply; a meter may display an average or varying reading depending on its settings and the control signal. Use the specified test equipment and method. Loss of communication with the pump module can shut the pump off even though the pump itself is sound. The failure modes and the tests are on fuel pump faults and the test page.