Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Diagnostics
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 4 to revision 14

Removed text is struck through; added text is highlighted.

See also testing a lambda sensor with propane enrichment for a controlled rich-response check, interpretation and workshop precautions.

Fuel trims show how much an engine control unit (ECU) is correcting its calculated fuel delivery in response to exhaust oxygen feedback. They are useful diagnostic clues even when no fault code is stored. This guide focuses on closed-loop petrol engines; diesel, lean-burn and some direct-injection strategies use different controls and displays.

How the feedback loop works

The ECU calculates a base fuel quantity from measured or estimated air and operating conditions. When the system enters closed loop, it compares exhaust sensor feedback with the commanded mixture and adjusts fuelling. For conventional petrol at stoichiometry, lambda is 1; the familiar approximately 14.7:1 air-to-fuel ratio is an approximation and changes with fuel composition. Other operating conditions may call for a different mixture.

Original illustration created for Tuning Wiki.

1. Calculate2. Deliver3. Measure4. CorrectAir, speed, temperature and load → base fuelInjectors deliver fuel → combustionUpstream lambda sensor measures exhaust oxygenECU compares feedback with target → adjusts fuel and repeats

Diagram: simplified closed-loop fuel control. The exact inputs and control strategy depend on the vehicle. US EPA: fuel system trim and feedback.

Short-term and long-term trim

Short-term fuel trim (STFT) is the faster feedback correction. It changes as the ECU responds to the sensor and operating conditions.Long-term fuel trim (LTFT) is a learned correction that can take over a persistent adjustment, leaving STFT room to respond. Some ECUs learn separate corrections for idle, part load and other operating regions.

DisplayWhat the ECU is doingWhat it suggestsPositive percentageAdding fuel relative to its base calculationFeedback indicates a lean tendency, or feedback is misleadingNegative percentageRemoving fuel relative to its base calculationFeedback indicates a rich tendency, or feedback is misleadingNear zeroLittle indicated correction for that value at that momentCheck loop status and both trims; a zero or inactive STFT does not prove the system is healthy

Read fuel-system status alongside the trims. During open-loop operation, such as some cold-start, fault or high-load conditions, the displayed STFT may be inactive, fixed or otherwise not a live closed-loop correction. Some ECUs still apply learned corrections in open loop; behaviour varies. A recently reset LTFT near zero also does not establish that the underlying fault is fixed.

Some manufacturer-specific data uses a multiplier or a different name instead of a percentage: for example, 1.00 may mean no correction. Do not confuse that correction factor with lambda 1.00. Check the data definition for the vehicle. Manufacturer explanation of fuel corrections and learning.

On systems where the manufacturer specifies it, STFT and LTFT for the same bank can be added as a useful approximate indication of total correction. For example, +12% LTFT and −3% STFT suggest approximately +9% overall. It is a diagnostic approximation, not a universal formula for exact injector pulse width. A small STFT alone can hide a large learned LTFT. Compare with the manufacturer's method, limits and conditions.

Give each steady operating point time to settle and record STFT and LTFT together. An LTFT change between idle and part load may reflect a switch to another learned cell rather than an immediate change in the fault. Keep the vehicle, bank, temperature, loop status and PID definition consistent when comparing readings. Manufacturer explanation of idle and part-load adaptations.

Reading the pattern

Original illustration created for Tuning Wiki. The points are examples, not diagnostic limits; several faults can produce similar patterns.

Observed patternPossible direction for testing Positive at warm idle, closer to zero at a steady raised speedInvestigate an intake or crankcase ventilation leak; airflow measurement and other faults can produce similar results. Positive at idle and under load, or increasingly positive under loadCheck fuel delivery and pressure under the specified conditions, air measurement, injectors and exhaust leaks. A stationary raised-speed test is not a substitute for a load test. Negative in several operating regionsInvestigate excess fuel, purge flow, fuel pressure, injector leakage or a biased sensor/input, according to the vehicle's test plan. One bank differs from the otherCompare bank-specific intake and exhaust leaks, injectors and sensor circuits. A shared fault can still affect banks differently. Large corrections but no codeRecord the evidence and investigate; a fault may not have met its monitor conditions or threshold.

These are hypotheses, not component verdicts. For example, a fixed air leak often has a greater proportionate effect at idle, but different airflow models and faults can change the pattern. A GM service procedure for specific vehicles compares idle and approximately 2,000 rpm and lists several possible causes when trim improves; it does not establish a universal limit. GM service information.

Worked example: positive trim at idleIllustrative example: a warm, single-bank petrol engine with a mass-airflow sensor idles roughly. The scan tool reports closed-loop control, and the technician has recorded the fault codes and freeze-frame data without resetting adaptations. The figures below are invented to show the reasoning; they are not universal pass limits. For this example, the vehicle procedure permits STFT and LTFT from the same bank to be added as an approximate diagnostic correction.Warm idle, bank 1: LTFT +12%, STFT approximately +10%; combined indication approximately +22%.Steady 2,000 rpm in Park, bank 1: LTFT +3%, STFT approximately +2%; combined indication approximately +5%.Interpretation: at idle the ECU is adding substantial fuel in response to its feedback. At raised speed the indicated correction is smaller. This pattern makes an intake or crankcase-ventilation air leak a reasonable test direction, because a leak can be a larger proportion of the total airflow at idle. It does not prove a leak: airflow measurement, a change of learned cell or other faults can also affect the comparison. The readings are taken at stable conditions with the engine still in closed loop; a raised-speed test in Park does not test fuel delivery under road load. GM service information: idle and raised-speed comparison on specified vehicles.Test and repair: following the vehicle and smoke-machine procedures, the technician finds smoke escaping from a split intake vacuum hose downstream of the airflow sensor. The hose is replaced and a repeat leak test shows no smoke at the repair. The smoke test confirms a leak at that location; the fuel-trim pattern alone did not identify the hose.Verify: after the appropriate relearn and with closed loop confirmed, the same bank is checked at the same operating points. In this example idle now reads LTFT +2% and STFT approximately +1%; at 2,000 rpm it reads LTFT +1% and STFT approximately +2%. The rough idle has gone and the fault does not return on a suitable test drive. These results support the repair; compare actual readings and readiness with the vehicle procedure, and do not treat an immediately reset LTFT as proof of success.Worked example: negative fuel trimIllustrative example: a single-bank petrol engine runs in closed loop at normal temperature and has a stored P0172. The technician records the codes, freeze-frame data and trims before clearing or resetting anything. The following values and test results are invented to demonstrate the method; they are not universal diagnostic limits. This example assumes the vehicle's procedure allows the two trims for the same bank to be added for an approximate combined indication.Warm idle, bank 1: LTFT −16%, STFT approximately −5%; combined indication approximately −21%.Steady 2,000 rpm in Park, bank 1: LTFT −12%, STFT approximately −3%; combined indication approximately −15%.Interpretation: the ECU is removing fuel in both conditions in response to its feedback. This suggests a rich tendency, but the numbers alone do not prove that the fuel injectors or lambda sensor are faulty. Excess fuel vapour, high fuel pressure, injector leakage, inaccurate airflow or temperature inputs, and misleading sensor feedback are among the possibilities. Learned values can differ between operating cells, and the stationary raised-speed test does not establish what happens under load.Narrowing it down: in this example, the technician checks the relevant service information, fuel specification, sensor data and fuel delivery using the manufacturer's procedures. No fault is found in those checks. The oil level is above its expected range and the oil smells strongly of fuel; the vehicle has repeatedly been driven on very short trips. Further investigation confirms fuel-diluted oil and finds no fuel-system fault responsible. Fuel vapour from the crankcase can contribute to a rich condition through the ventilation system. Fuel smell or oil level alone does not establish the cause: investigate and repair any fuel leak or other underlying fault. A GM bulletin describes fuel-diluted oil associated with short trips and negative LTFT on specified vehicles; its procedure and limits are vehicle-specific.Repair and verify: in this example the confirmed contaminated oil and filter are replaced using the vehicle procedure. The technician clears the code as directed, allows the ECU to relearn, then repeats the warm closed-loop checks at the same operating points. Idle now shows LTFT −2% and STFT approximately −1%; at 2,000 rpm LTFT is −1% and STFT approximately −2%. Following an appropriate test drive, the code has not returned. Compare readings and monitor status with the vehicle's procedure: a zero LTFT immediately after a reset is not proof of repair, and a test drive alone may not complete every monitor.Worked example: different readings between banksIllustrative example: a warm V-engine with separate upstream sensors and bank-specific trims has a rough idle and a stored P0171. The technician records the codes and freeze-frame data before clearing anything, confirms closed-loop operation, and uses the vehicle information to identify bank 1 and its upstream sensor. The readings and test results below are invented; they are not universal limits. In this example the vehicle procedure permits STFT and LTFT on the same bank to be added for an approximate combined indication.Bank 1 at stable idle: LTFT +14%, STFT approximately +6%; combined indication approximately +20%.Bank 2 at the same idle: LTFT +2%, STFT approximately +1%; combined indication approximately +3%.At a steady 2,000 rpm in Park: bank 1 is approximately +7% combined and bank 2 approximately +3%, with both banks still in closed loop.Interpretation: bank 1 is adding considerably more fuel at idle, so investigate faults that can affect its cylinders or feedback more strongly. The lower bank 1 correction at raised speed makes an intake leak near that bank one possibility. A bank-specific exhaust leak ahead of the sensor, injector problem, or sensor or wiring fault can also produce a difference. A shared fault can affect the banks unequally, and a change of learned cell may influence the comparison. The trims are clues, not proof of a failed component. Subaru diagnostic guidance on intake and upstream exhaust leaks.Test and repair: using the vehicle and equipment procedures, the technician performs a regulated intake smoke test and finds a leak at the intake manifold seal adjoining a bank 1 runner. In this invented case the seal is replaced, and a repeat leak test shows no smoke at the repair. The leak test identifies the location; the difference in trims alone could not establish it. If no leak were found, the next checks would follow the vehicle's diagnostic procedure for bank 1 fuel delivery, exhaust and sensor circuit.Verify: after the appropriate relearn, the technician repeats the warm closed-loop idle and raised-speed checks on both banks. At idle, bank 1 now reads LTFT +2% and STFT approximately +1%, while bank 2 reads LTFT +2% and STFT approximately 0%. The rough idle has cleared, and the code does not return during an appropriate test drive. Compare readings and monitor status with the vehicle procedure; an immediately reset LTFT is not proof of repair. A stationary 2,000 rpm check does not test fuel delivery under road load.Worked example: misleading lambda sensor feedbackIllustrative example: a warm petrol engine with a conventional upstream narrowband sensor idles roughly and uses more fuel than expected. Closed-loop control is active. The technician records the fault codes, freeze-frame data and trims before resetting anything. The figures and test results below are invented to demonstrate the diagnosis; they are not vehicle specifications. This example assumes the manufacturer permits the trims from the same bank to be added for an approximate combined indication.Bank 1 at stable idle: LTFT +12%, STFT approximately +9%; combined indication approximately +21%.Upstream sensor data: the scan tool reports a low, lean-indicating signal for much of the test.Independent check: a correctly used exhaust gas analyser indicates a rich exhaust under the test conditions.Interpretation: the ECU is adding fuel because of what its feedback indicates, yet the separate exhaust measurement suggests the actual exhaust is rich. This disagreement makes the feedback path worth investigating; it does not by itself prove that the sensor is defective. Confirm the analyser setup, sampling point and interpretation for the vehicle, and investigate intake and upstream exhaust leaks, misfire and fuelling faults. Scan-tool readings are processed data and may not show every signal fault. Bosch: comparing sensor data and exhaust gas readings.Narrowing it down: in this invented case the specified leak, combustion and fuel-system checks do not identify a fault. The technician identifies the sensor type and uses the manufacturer's test procedure, correct connections and a suitable oscilloscope to compare the sensor signal and the ECU-side input. During the prescribed response checks, the sensor-side waveform responds as expected, but the ECU-side signal is intermittently low. Inspection and circuit testing then reveal a damaged connector and wiring fault between the sensor and ECU. The disagreement localises the problem to the feedback circuit; it does not justify replacing the sensor without further evidence. A GM bulletin illustrates that contaminated oxygen-sensor wiring can skew readings on specified vehicles; its remedy is specific to those vehicles and its particular fault.Repair and verify: the damaged wiring and connector are repaired according to the vehicle procedure, and the sensor-side and ECU-side signals are checked again. After the appropriate relearn and with closed loop confirmed, the same idle condition now shows LTFT +2% and STFT approximately +1%; the gas-analyser result is consistent with the commanded operating condition and the rough idle has cleared. The code does not return on an appropriate test drive. Compare monitor status and readings against the vehicle procedure; a recently reset LTFT alone is not proof of repair.This example is for a conventional narrowband sensor. Wideband sensors use different control circuits and signals; never apply a generic 0–1 V test or probe an unfamiliar circuit without the manufacturer's procedure. Bosch: sensor signal types and test conditions.Worked example: positive fuel trim under loadIllustrative example: a single-bank, port-injected petrol engine drives normally at idle but hesitates during a steady uphill drive. The technician records the complaint, any codes and freeze-frame data before resetting adaptations. The figures and test results below are invented to show the reasoning; they are not universal limits. In this example the vehicle procedure allows STFT and LTFT for the same bank to be added as an approximate combined indication.Warm idle, bank 1: LTFT +2%, STFT approximately +1%; combined indication approximately +3%.Steady moderate load, bank 1: LTFT +8%, STFT approximately +10%; combined indication approximately +18%. Closed-loop control remains active at the recorded point.Interpretation: the ECU is adding much more fuel at the loaded point. A fuel supply that cannot maintain the required delivery is one possibility; inaccurate airflow measurement, injector restriction, an exhaust leak or misleading sensor feedback can also produce positive correction. Different learned cells may contribute to the change. The trim pattern alone cannot identify the defective part, and free-revving in Park does not reproduce road load.Narrowing it down: the technician checks the vehicle's service information and inspects the intake, airflow-sensor installation, exhaust and wiring. A suitable log is captured at the moderate-load condition on a safe road or dynamometer, with a second person operating the equipment. Fuel-system status, engine speed, load, both trims, commanded and measured lambda where supported, and the relevant fuel-pressure data are recorded. The test is stopped if the engine runs severely lean or misfires; higher load or full throttle is not required to prove the point. On systems that enter open loop at high load, STFT may stop being a live correction, so interpret it only with the control status and vehicle-specific data.Test and repair: in this example, fuel pressure is within the manufacturer's specified range at idle but falls below the required pressure during the recorded moderate-load condition. The technician confirms the measurement with the approved equipment, then follows the vehicle's fuel pressure, delivery and electrical tests. A restriction is confirmed at a serviceable fuel filter; pump supply and control test correctly. The filter is replaced and the fuel system is rechecked for leaks. A pressure drop alone would not prove the filter or pump is faulty. Bosch: fuel supply and reduced delivery.Verify: after the appropriate relearn, the technician repeats the same warm closed-loop idle and moderate-load checks. In this example idle reads LTFT +1% and STFT approximately +1%; under the same load LTFT is +2% and STFT approximately +2%. Fuel pressure remains within the vehicle's specification, the hesitation is gone, and no relevant fault returns during the prescribed test. Check monitor status as well: an immediately reset LTFT or a short test drive alone is not proof that every monitor has completed.Use the manufacturer's approved connections, pressure-relief steps and test equipment. Petrol direct-injection systems can retain high pressure, and their low- and high-pressure circuits require their own procedures.Worked example: a faulty mass airflow sensorIllustrative example: a warm, single-bank petrol engine with a mass airflow (MAF) sensor hesitates at moderate load and has a stored P0171. The technician records the codes, freeze-frame data and trims before clearing anything. The numbers and test results below are invented to show the method; they are not specifications. For this example, the vehicle procedure permits same-bank STFT and LTFT to be added as an approximate combined indication.Warm idle, bank 1: LTFT +3%, STFT approximately +2%; combined indication approximately +5%.Steady moderate load, bank 1: LTFT +9%, STFT approximately +10%; combined indication approximately +19%. The fuel system remains in closed loop.Interpretation: the ECU is adding more fuel at the loaded point. A MAF sensor that under-reports airflow can contribute to a lean tendency, but these trims do not prove the sensor is faulty. Fuel delivery, unmetered air, intake configuration, exhaust leaks, sensor feedback and changes in learned cells are also possible. Closed-loop status must be checked at each point; a free-rev test in Park does not reproduce road load.Narrowing it down: the technician follows the vehicle's diagnostic procedure, inspects the air filter, MAF housing and ducting, and checks for air leaks downstream of the MAF. Intake and upstream exhaust leak checks, fuel-pressure and delivery tests, and checks of the MAF power, ground, wiring and connector reveal no fault in this example. A low reported airflow value by itself does not establish a bad MAF: an air leak or disturbed airflow can produce misleading readings. GM: low MAF readings and intake-system causes on specified vehicles.At the same steady speed, load and operating temperature on a dynamometer, the suspect sensor reports approximately 14 g/s; a verified compatible known-good sensor temporarily fitted in the same housing reports approximately 19 g/s. With the known-good sensor installed, the short-term correction moves towards zero while the learned long-term value initially remains positive. Reinstalling the original sensor reproduces the low reading and positive correction. The comparison supports a biased sensor after the other checks; these airflow values are illustrative and must not be used as another engine's specification. Use the manufacturer's comparison method and account for normal test variation. Subaru: P0171 metering-device and leak checks.Repair and verify: the confirmed faulty MAF is replaced with the correct part, and the intake is reassembled and checked. After the appropriate relearn, the technician repeats the warm closed-loop idle and moderate-load checks. In this example idle shows LTFT +2% and STFT approximately +1%; at the same load LTFT is +2% and STFT approximately +2%. The hesitation has gone, and no relevant code returns during the prescribed test. Check monitor status and the manufacturer's limits; an immediately reset LTFT alone is not proof of repair. A road test requires a driver and a second person to operate the diagnostic equipment.Worked example: a leaking fuel injectorIllustrative example: a single-bank, port-injected petrol engine has a rough idle and a difficult warm restart. The technician records the complaint, any codes, freeze-frame data and trims before clearing or resetting anything. The readings and test results below are invented to demonstrate the reasoning; they are not universal specifications. In this example the manufacturer's procedure permits same-bank STFT and LTFT to be added as an approximate combined indication.Warm idle, bank 1: LTFT −12%, STFT approximately −6%; combined indication approximately −18%, with closed-loop control active.Steady 2,000 rpm in Park, bank 1: LTFT −7%, STFT approximately −3%; combined indication approximately −10%, still in closed loop.Interpretation: the ECU is removing fuel in response to feedback, suggesting a rich tendency. An injector leaking fuel is one possibility, but excessive fuel pressure, purge vapour, fuel-contaminated oil, airflow or temperature errors, and misleading lambda feedback can also cause negative correction. A misfire can leave oxygen in the exhaust and complicate the feedback, so the sign of trim alone does not prove or exclude an injector fault. The raised-speed check in Park does not reproduce road load.Narrowing it down: the technician follows the vehicle's diagnostic procedure, checks the reported operating conditions and fuel pressure, and investigates purge flow, sensor readings and ignition. In this example those checks reveal no fault. The cylinder-specific diagnostic data points to cylinder 2, and the manufacturer's fuel-pressure retention test shows that pressure falls faster than its specification after shutdown. That result supports further testing but does not identify the leak by itself: the pump, regulator, lines, connections or other components may also cause pressure loss.Confirm and repair: following the vehicle procedure for pressure relief and removal, the technician sends the suspect injector for an appropriate injector leak test. In this invented case it leaks from its nozzle while commanded closed, outside the tester's specification; the remaining injectors pass. Circuit checks show that the injector is not being held open electrically. The correct injector is fitted using the manufacturer's installation instructions, seals and any required coding, and the fuel system is checked for leaks. GM: injector testing to isolate a leaking injector on specified engines.Verify: the pressure retention test is repeated and now meets the vehicle's specification. After the appropriate relearn, warm closed-loop idle shows LTFT −2% and STFT approximately −1%; at the same raised speed LTFT is −1% and STFT approximately −1%. The restart and idle concerns have cleared, and no relevant fault returns during the prescribed test. Check monitor status and inspect the oil if fuel dilution is suspected; a recently reset LTFT alone is not proof of repair.Use approved equipment and the vehicle's fuel-pressure relief, containment and fire precautions before opening a fuel system. Petrol direct-injection systems can retain much higher pressure and require their own manufacturer-specific test and service procedures; do not transfer the port-injection method or limits to them. Bosch: petrol high-pressure injector service.Worked example: a faulty EVAP purge valveIllustrative example: a warm, single-bank petrol engine runs roughly at idle, particularly after refuelling. It uses a normally closed purge valve to control flow from the evaporative-emissions (EVAP) canister into the intake. The technician records any codes, freeze-frame data and trims before clearing or resetting anything. The values and results below are invented to demonstrate the reasoning; they are not universal test limits. For this example, the manufacturer permits same-bank STFT and LTFT to be added as an approximate combined indication.Warm idle, bank 1: LTFT −12%, STFT approximately −6%; combined indication approximately −18%, with closed-loop control active.Scan-tool data: the ECU is commanding purge closed at the recorded idle point. This is a command, not proof that the valve has sealed.Interpretation: the ECU is removing fuel in response to feedback. Excess fuel vapour passing through a valve that is leaking when closed is one possible cause; leaking injectors, fuel pressure, fuel-contaminated oil and sensor or circuit faults are others. Purge vapour concentration varies, and unintended flow can also act as an air leak, so a purge fault does not always produce negative trim. The numbers alone cannot identify the valve.Narrowing it down: following the vehicle-specific procedure, the technician temporarily isolates the purge path and seals the specified openings, then repeats the warm idle test in closed loop. In this invented case STFT moves from approximately −6% to +8% while LTFT remains around −12%: the approximate combined indication moves from −18% to −4%. The learned value may take time to change. This response points towards the purge path but does not prove that the valve itself is defective. The system is returned to its normal configuration after the test. GM: purge-valve checks on specified vehicles.Confirm and repair: the technician checks the valve's control circuit and its ability to seal and open using the manufacturer's procedure and approved test equipment. In this example the control circuit tests correctly, but the disconnected, unpowered normally closed valve fails its specified sealing test and allows flow. The valve is replaced, its connections restored, and the EVAP system is checked for leaks. A valve that is being electrically commanded open, a damaged hose or another system fault needs its own diagnosis.Verify: after the appropriate relearn, the technician repeats the same warm closed-loop idle check with the complete EVAP system connected. In this example LTFT is −2% and STFT approximately −1%; idle quality is restored and the original complaint does not recur during the prescribed test. Check fault codes and EVAP monitor status according to the vehicle procedure: a short drive may not complete the monitor, and an immediately reset LTFT is not proof of repair.Follow the vehicle and equipment instructions when isolating or leak-testing an EVAP system. Use the specified inert gas and pressure limits for fuel-vapour testing, keep ignition sources away, and never leave the purge path disconnected or plugged after diagnosis. Bosch: fuel-system leak testing.Worked example: exhaust leak upstream of the lambda sensorIllustrative example: a warm petrol V-engine has an exhaust ticking noise and a stored P0171. The technician records codes, freeze-frame data and both banks' trims before clearing or resetting anything, confirms closed-loop operation and identifies each bank and upstream sensor using the vehicle information. The figures and results below are invented to show the reasoning; they are not universal limits. In this example the vehicle procedure permits STFT and LTFT from the same bank to be added as an approximate combined indication.Bank 1 at stable idle: LTFT +12%, STFT approximately +8%; combined indication approximately +20%.Bank 2 at the same idle: LTFT +2%, STFT approximately +1%; combined indication approximately +3%.Scan-tool feedback: bank 1's upstream sensor indicates a lean tendency. The sound is most noticeable near the bank 1 exhaust manifold.Interpretation: the ECU is adding more fuel on bank 1. A leak between that bank's cylinders and its upstream sensor may allow outside oxygen into the exhaust under some conditions; the sensor can then report a leaner mixture than the combustion alone produced. The correction and noise do not prove the leak is the cause: intake leaks, injector or fuel delivery faults, misfire and sensor or wiring faults remain possible. A leak at the sensor boss or upstream can produce a false lean indication, as described in this Toyota exhaust-leak technical tip.Test and repair: in this invented case, intake and fuel-system checks do not identify a fault. With the engine off and exhaust cool, the technician follows the vehicle and leak-tester procedures to inspect the bank 1 manifold, joints and sensor boss. A regulated exhaust leak test reveals escaping smoke at the manifold-to-pipe joint upstream of the sensor. The faulty joint seal is replaced using the manufacturer's procedure and the exhaust test is repeated with no leak found at the repair. The smoke test identifies an outward leak at that location; the trim readings alone did not establish it. GM: exhaust leak detection guidance for specified vehicles.Verify: after the appropriate relearn, the technician repeats the same warm closed-loop idle check on both banks. In this example bank 1 now reads LTFT +2% and STFT approximately +1%; bank 2 reads LTFT +2% and STFT approximately 0%. The ticking has stopped and no relevant fault returns during the prescribed test. Compare readings and monitor status with the vehicle's procedure; an immediately reset LTFT is not proof of repair, and the sensor should not be replaced merely because the code or feedback appeared lean.Use the manufacturer's approved leak-test equipment and pressure limits. Keep clear of hot exhaust components and ensure exhaust gases are safely extracted when the engine runs.

Common fault codes

P0171 and P0172 generally identify a lean and a rich fuel-system condition on bank 1; P0174 and P0175 identify lean and rich conditions on bank 2 respectively. The code indicates the monitor result, not the failed component. Confirm the exact description and diagnostic procedure for the vehicle, including its bank identification. Monitor thresholds and enabling conditions vary. Toyota: fuel-trim code examples.

Workshop procedure

Record the complaint, fuel type, modifications, stored and pending codes, freeze-frame data and readiness. Inspect intake ducting, hoses, PCV connections, wiring and exhaust for obvious faults. Do not clear codes or adaptations before recording the evidence. Bring the engine to the relevant temperature and verify fuel-control status. Log STFT and LTFT for each available bank, engine speed, load, coolant temperature, airflow or manifold pressure, commanded lambda and upstream sensor data where supported. Record a stable idle, then a stable raised speed in a safe stationary position, following the vehicle procedure. Compare the same bank and operating conditions. If the concern occurs under load, capture a suitable road or dynamometer log safely with a second person operating the scan tool. Use the pattern to select a test: a regulated smoke test for an intake leak, fuel pressure and delivery tests under the specified conditions, injector tests, or checks of airflow and sensor wiring. Follow vehicle and equipment procedures for pressure and test medium; do not apply unregulated shop air to the crankcase or fuel system. For fuel-vapour systems, use the specified inert gas and leak-test equipment. Petrol direct-injection systems can retain high pressure: follow the manufacturer’s depressurisation and connection procedure before opening a fuel circuit. Bosch: leak testing and inert gas. If sensor feedback and other evidence disagree, compare with an exhaust gas analyser and test the sensor and circuit using the correct procedure. Scan-tool values are processed and may be limited or filtered; a suitable oscilloscope can reveal a signal the displayed data does not show. Check the circuit, reference and heater as applicable before replacing parts. Repair the confirmed cause, then follow the manufacturer's instructions for clearing faults or resetting adaptations if appropriate. Recheck for leaks, repeat the original operating conditions and allow the ECU to relearn before judging the final result.

When feedback tells the wrong story

A positive trim means the ECU is adding fuel; it does not independently prove that the actual exhaust mixture is lean. An exhaust leak upstream of the sensor, misfire, wiring fault or a faulty sensor can distort the oxygen signal. If a gas analyser indicates a rich exhaust while the ECU is adding fuel, investigate the feedback and its circuit as well as the fuelling system. A newly fitted sensor or other part still needs to be tested. Bosch recommends comparing sensor data with exhaust-gas readings and, where necessary, checking the signal with an oscilloscope. Bosch: lambda and air-mass sensor diagnosis.

A conventional narrowband zirconia sensor and a wideband air–fuel sensor have different signals and test methods. Do not apply a 0–1 V switching test to every sensor; use the manufacturer's pinout, equipment and procedure. Exhaust oxygen can also be affected by misfire, so interpret the signal alongside combustion and gas-analysis evidence. Bosch: lambda sensor signal types.

Related reading

Common-rail fuel system testsCrankcase ventilation and PCV systemsEVAP systems and charcoal canisters

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 4: Fuel trims

Fuel trims show how much an engine control unit (ECU) is correcting its calculated fuel delivery in response to exhaust oxygen feedback. They are useful diagnostic clues even when no fault code is stored. This guide focuses on closed-loop petrol engines; diesel, lean-burn and some direct-injection strategies use different controls and displays.

How the feedback loop works

The ECU calculates a base fuel quantity from measured or estimated air and operating conditions. When the system enters closed loop, it compares exhaust sensor feedback with the commanded mixture and adjusts fuelling. For conventional petrol at stoichiometry, lambda is 1; the familiar approximately 14.7:1 air-to-fuel ratio is an approximation and changes with fuel composition. Other operating conditions may call for a different mixture.

Closed-loop fuel control: ECU calculates fuel, injectors supply the engine, the upstream lambda sensor measures exhaust oxygen, and feedback returns to the ECU.

Original illustration created for Tuning Wiki.

1. Calculate2. Deliver3. Measure4. Correct
Air, speed, temperature and load → base fuelInjectors deliver fuel → combustionUpstream lambda sensor measures exhaust oxygenECU compares feedback with target → adjusts fuel and repeats

Diagram: simplified closed-loop fuel control. The exact inputs and control strategy depend on the vehicle. US EPA: fuel system trim and feedback.

Short-term and long-term trim

  • Short-term fuel trim (STFT) is the faster feedback correction. It changes as the ECU responds to the sensor and operating conditions.
  • Long-term fuel trim (LTFT) is a learned correction that can take over a persistent adjustment, leaving STFT room to respond. Some ECUs learn separate corrections for idle, part load and other operating regions.
DisplayWhat the ECU is doingWhat it suggests
Positive percentageAdding fuel relative to its base calculationFeedback indicates a lean tendency, or feedback is misleading
Negative percentageRemoving fuel relative to its base calculationFeedback indicates a rich tendency, or feedback is misleading
Near zeroLittle indicated correction for that value at that momentCheck loop status and both trims; a zero or inactive STFT does not prove the system is healthy

Read fuel-system status alongside the trims. During open-loop operation, such as some cold-start, fault or high-load conditions, the displayed STFT may be inactive, fixed or otherwise not a live closed-loop correction. Some ECUs still apply learned corrections in open loop; behaviour varies. A recently reset LTFT near zero also does not establish that the underlying fault is fixed.

\n

Some manufacturer-specific data uses a multiplier or a different name instead of a percentage: for example, 1.00 may mean no correction. Do not confuse that correction factor with lambda 1.00. Check the data definition for the vehicle. Manufacturer explanation of fuel corrections and learning.

On systems where the manufacturer specifies it, STFT and LTFT for the same bank can be added as a useful approximate indication of total correction. For example, +12% LTFT and −3% STFT suggest approximately +9% overall. It is a diagnostic approximation, not a universal formula for exact injector pulse width. A small STFT alone can hide a large learned LTFT. Compare with the manufacturer's method, limits and conditions.

Give each steady operating point time to settle and record STFT and LTFT together. An LTFT change between idle and part load may reflect a switch to another learned cell rather than an immediate change in the fault. Keep the vehicle, bank, temperature, loop status and PID definition consistent when comparing readings. Manufacturer explanation of idle and part-load adaptations.

\n

Reading the pattern

Illustrative trim patterns: positive trim improving at raised rpm, positive trim persisting under load, and negative trim at two operating points.

Original illustration created for Tuning Wiki. The points are examples, not diagnostic limits; several faults can produce similar patterns.

Observed patternPossible direction for testing
Positive at warm idle, closer to zero at a steady raised speedInvestigate an intake or crankcase ventilation leak; airflow measurement and other faults can produce similar results.
Positive at idle and under load, or increasingly positive under loadCheck fuel delivery and pressure under the specified conditions, air measurement, injectors and exhaust leaks. A stationary raised-speed test is not a substitute for a load test.
Negative in several operating regionsInvestigate excess fuel, purge flow, fuel pressure, injector leakage or a biased sensor/input, according to the vehicle's test plan.
One bank differs from the otherCompare bank-specific intake and exhaust leaks, injectors and sensor circuits. A shared fault can still affect banks differently.
Large corrections but no codeRecord the evidence and investigate; a fault may not have met its monitor conditions or threshold.

These are hypotheses, not component verdicts. For example, a fixed air leak often has a greater proportionate effect at idle, but different airflow models and faults can change the pattern. A GM service procedure for specific vehicles compares idle and approximately 2,000 rpm and lists several possible causes when trim improves; it does not establish a universal limit. GM service information.

Common fault codes

P0171 and P0172 generally identify a lean and a rich fuel-system condition on bank 1; P0174 and P0175 identify lean and rich conditions on bank 2 respectively. The code indicates the monitor result, not the failed component. Confirm the exact description and diagnostic procedure for the vehicle, including its bank identification. Monitor thresholds and enabling conditions vary. Toyota: fuel-trim code examples.

\n

Workshop procedure

  1. Record the complaint, fuel type, modifications, stored and pending codes, freeze-frame data and readiness. Inspect intake ducting, hoses, PCV connections, wiring and exhaust for obvious faults. Do not clear codes or adaptations before recording the evidence.
  2. Bring the engine to the relevant temperature and verify fuel-control status. Log STFT and LTFT for each available bank, engine speed, load, coolant temperature, airflow or manifold pressure, commanded lambda and upstream sensor data where supported.
  3. Record a stable idle, then a stable raised speed in a safe stationary position, following the vehicle procedure. Compare the same bank and operating conditions. If the concern occurs under load, capture a suitable road or dynamometer log safely with a second person operating the scan tool.
  4. Use the pattern to select a test: a regulated smoke test for an intake leak, fuel pressure and delivery tests under the specified conditions, injector tests, or checks of airflow and sensor wiring. Follow vehicle and equipment procedures for pressure and test medium; do not apply unregulated shop air to the crankcase or fuel system. For fuel-vapour systems, use the specified inert gas and leak-test equipment. Petrol direct-injection systems can retain high pressure: follow the manufacturer’s depressurisation and connection procedure before opening a fuel circuit. Bosch: leak testing and inert gas.
  5. If sensor feedback and other evidence disagree, compare with an exhaust gas analyser and test the sensor and circuit using the correct procedure. Scan-tool values are processed and may be limited or filtered; a suitable oscilloscope can reveal a signal the displayed data does not show. Check the circuit, reference and heater as applicable before replacing parts.
  6. Repair the confirmed cause, then follow the manufacturer's instructions for clearing faults or resetting adaptations if appropriate. Recheck for leaks, repeat the original operating conditions and allow the ECU to relearn before judging the final result.

When feedback tells the wrong story

A positive trim means the ECU is adding fuel; it does not independently prove that the actual exhaust mixture is lean. An exhaust leak upstream of the sensor, misfire, wiring fault or a faulty sensor can distort the oxygen signal. If a gas analyser indicates a rich exhaust while the ECU is adding fuel, investigate the feedback and its circuit as well as the fuelling system. A newly fitted sensor or other part still needs to be tested. Bosch recommends comparing sensor data with exhaust-gas readings and, where necessary, checking the signal with an oscilloscope. Bosch: lambda and air-mass sensor diagnosis.

A conventional narrowband zirconia sensor and a wideband air–fuel sensor have different signals and test methods. Do not apply a 0–1 V switching test to every sensor; use the manufacturer's pinout, equipment and procedure. Exhaust oxygen can also be affected by misfire, so interpret the signal alongside combustion and gas-analysis evidence. Bosch: lambda sensor signal types.

Related reading

Revision 14: Fuel trims

See also testing a lambda sensor with propane enrichment for a controlled rich-response check, interpretation and workshop precautions.

Fuel trims show how much an engine control unit (ECU) is correcting its calculated fuel delivery in response to exhaust oxygen feedback. They are useful diagnostic clues even when no fault code is stored. This guide focuses on closed-loop petrol engines; diesel, lean-burn and some direct-injection strategies use different controls and displays.

How the feedback loop works

The ECU calculates a base fuel quantity from measured or estimated air and operating conditions. When the system enters closed loop, it compares exhaust sensor feedback with the commanded mixture and adjusts fuelling. For conventional petrol at stoichiometry, lambda is 1; the familiar approximately 14.7:1 air-to-fuel ratio is an approximation and changes with fuel composition. Other operating conditions may call for a different mixture.

Closed-loop fuel control: ECU calculates fuel, injectors supply the engine, the upstream lambda sensor measures exhaust oxygen, and feedback returns to the ECU.

Original illustration created for Tuning Wiki.

1. Calculate2. Deliver3. Measure4. Correct
Air, speed, temperature and load → base fuelInjectors deliver fuel → combustionUpstream lambda sensor measures exhaust oxygenECU compares feedback with target → adjusts fuel and repeats

Diagram: simplified closed-loop fuel control. The exact inputs and control strategy depend on the vehicle. US EPA: fuel system trim and feedback.

Short-term and long-term trim

  • Short-term fuel trim (STFT) is the faster feedback correction. It changes as the ECU responds to the sensor and operating conditions.
  • Long-term fuel trim (LTFT) is a learned correction that can take over a persistent adjustment, leaving STFT room to respond. Some ECUs learn separate corrections for idle, part load and other operating regions.
DisplayWhat the ECU is doingWhat it suggests
Positive percentageAdding fuel relative to its base calculationFeedback indicates a lean tendency, or feedback is misleading
Negative percentageRemoving fuel relative to its base calculationFeedback indicates a rich tendency, or feedback is misleading
Near zeroLittle indicated correction for that value at that momentCheck loop status and both trims; a zero or inactive STFT does not prove the system is healthy

Read fuel-system status alongside the trims. During open-loop operation, such as some cold-start, fault or high-load conditions, the displayed STFT may be inactive, fixed or otherwise not a live closed-loop correction. Some ECUs still apply learned corrections in open loop; behaviour varies. A recently reset LTFT near zero also does not establish that the underlying fault is fixed.

Some manufacturer-specific data uses a multiplier or a different name instead of a percentage: for example, 1.00 may mean no correction. Do not confuse that correction factor with lambda 1.00. Check the data definition for the vehicle. Manufacturer explanation of fuel corrections and learning.

On systems where the manufacturer specifies it, STFT and LTFT for the same bank can be added as a useful approximate indication of total correction. For example, +12% LTFT and −3% STFT suggest approximately +9% overall. It is a diagnostic approximation, not a universal formula for exact injector pulse width. A small STFT alone can hide a large learned LTFT. Compare with the manufacturer's method, limits and conditions.

Give each steady operating point time to settle and record STFT and LTFT together. An LTFT change between idle and part load may reflect a switch to another learned cell rather than an immediate change in the fault. Keep the vehicle, bank, temperature, loop status and PID definition consistent when comparing readings. Manufacturer explanation of idle and part-load adaptations.

Reading the pattern

Illustrative trim patterns: positive trim improving at raised rpm, positive trim persisting under load, and negative trim at two operating points.

Original illustration created for Tuning Wiki. The points are examples, not diagnostic limits; several faults can produce similar patterns.

Observed patternPossible direction for testing
Positive at warm idle, closer to zero at a steady raised speedInvestigate an intake or crankcase ventilation leak; airflow measurement and other faults can produce similar results.
Positive at idle and under load, or increasingly positive under loadCheck fuel delivery and pressure under the specified conditions, air measurement, injectors and exhaust leaks. A stationary raised-speed test is not a substitute for a load test.
Negative in several operating regionsInvestigate excess fuel, purge flow, fuel pressure, injector leakage or a biased sensor/input, according to the vehicle's test plan.
One bank differs from the otherCompare bank-specific intake and exhaust leaks, injectors and sensor circuits. A shared fault can still affect banks differently.
Large corrections but no codeRecord the evidence and investigate; a fault may not have met its monitor conditions or threshold.

These are hypotheses, not component verdicts. For example, a fixed air leak often has a greater proportionate effect at idle, but different airflow models and faults can change the pattern. A GM service procedure for specific vehicles compares idle and approximately 2,000 rpm and lists several possible causes when trim improves; it does not establish a universal limit. GM service information.

Worked example: positive trim at idle

Illustrative example: a warm, single-bank petrol engine with a mass-airflow sensor idles roughly. The scan tool reports closed-loop control, and the technician has recorded the fault codes and freeze-frame data without resetting adaptations. The figures below are invented to show the reasoning; they are not universal pass limits. For this example, the vehicle procedure permits STFT and LTFT from the same bank to be added as an approximate diagnostic correction.

  • Warm idle, bank 1: LTFT +12%, STFT approximately +10%; combined indication approximately +22%.
  • Steady 2,000 rpm in Park, bank 1: LTFT +3%, STFT approximately +2%; combined indication approximately +5%.

Interpretation: at idle the ECU is adding substantial fuel in response to its feedback. At raised speed the indicated correction is smaller. This pattern makes an intake or crankcase-ventilation air leak a reasonable test direction, because a leak can be a larger proportion of the total airflow at idle. It does not prove a leak: airflow measurement, a change of learned cell or other faults can also affect the comparison. The readings are taken at stable conditions with the engine still in closed loop; a raised-speed test in Park does not test fuel delivery under road load. GM service information: idle and raised-speed comparison on specified vehicles.

Test and repair: following the vehicle and smoke-machine procedures, the technician finds smoke escaping from a split intake vacuum hose downstream of the airflow sensor. The hose is replaced and a repeat leak test shows no smoke at the repair. The smoke test confirms a leak at that location; the fuel-trim pattern alone did not identify the hose.

Verify: after the appropriate relearn and with closed loop confirmed, the same bank is checked at the same operating points. In this example idle now reads LTFT +2% and STFT approximately +1%; at 2,000 rpm it reads LTFT +1% and STFT approximately +2%. The rough idle has gone and the fault does not return on a suitable test drive. These results support the repair; compare actual readings and readiness with the vehicle procedure, and do not treat an immediately reset LTFT as proof of success.

Worked example: negative fuel trim

Illustrative example: a single-bank petrol engine runs in closed loop at normal temperature and has a stored P0172. The technician records the codes, freeze-frame data and trims before clearing or resetting anything. The following values and test results are invented to demonstrate the method; they are not universal diagnostic limits. This example assumes the vehicle's procedure allows the two trims for the same bank to be added for an approximate combined indication.

  • Warm idle, bank 1: LTFT −16%, STFT approximately −5%; combined indication approximately −21%.
  • Steady 2,000 rpm in Park, bank 1: LTFT −12%, STFT approximately −3%; combined indication approximately −15%.

Interpretation: the ECU is removing fuel in both conditions in response to its feedback. This suggests a rich tendency, but the numbers alone do not prove that the fuel injectors or lambda sensor are faulty. Excess fuel vapour, high fuel pressure, injector leakage, inaccurate airflow or temperature inputs, and misleading sensor feedback are among the possibilities. Learned values can differ between operating cells, and the stationary raised-speed test does not establish what happens under load.

Narrowing it down: in this example, the technician checks the relevant service information, fuel specification, sensor data and fuel delivery using the manufacturer's procedures. No fault is found in those checks. The oil level is above its expected range and the oil smells strongly of fuel; the vehicle has repeatedly been driven on very short trips. Further investigation confirms fuel-diluted oil and finds no fuel-system fault responsible. Fuel vapour from the crankcase can contribute to a rich condition through the ventilation system. Fuel smell or oil level alone does not establish the cause: investigate and repair any fuel leak or other underlying fault. A GM bulletin describes fuel-diluted oil associated with short trips and negative LTFT on specified vehicles; its procedure and limits are vehicle-specific.

Repair and verify: in this example the confirmed contaminated oil and filter are replaced using the vehicle procedure. The technician clears the code as directed, allows the ECU to relearn, then repeats the warm closed-loop checks at the same operating points. Idle now shows LTFT −2% and STFT approximately −1%; at 2,000 rpm LTFT is −1% and STFT approximately −2%. Following an appropriate test drive, the code has not returned. Compare readings and monitor status with the vehicle's procedure: a zero LTFT immediately after a reset is not proof of repair, and a test drive alone may not complete every monitor.

Worked example: different readings between banks

Illustrative example: a warm V-engine with separate upstream sensors and bank-specific trims has a rough idle and a stored P0171. The technician records the codes and freeze-frame data before clearing anything, confirms closed-loop operation, and uses the vehicle information to identify bank 1 and its upstream sensor. The readings and test results below are invented; they are not universal limits. In this example the vehicle procedure permits STFT and LTFT on the same bank to be added for an approximate combined indication.

  • Bank 1 at stable idle: LTFT +14%, STFT approximately +6%; combined indication approximately +20%.
  • Bank 2 at the same idle: LTFT +2%, STFT approximately +1%; combined indication approximately +3%.
  • At a steady 2,000 rpm in Park: bank 1 is approximately +7% combined and bank 2 approximately +3%, with both banks still in closed loop.

Interpretation: bank 1 is adding considerably more fuel at idle, so investigate faults that can affect its cylinders or feedback more strongly. The lower bank 1 correction at raised speed makes an intake leak near that bank one possibility. A bank-specific exhaust leak ahead of the sensor, injector problem, or sensor or wiring fault can also produce a difference. A shared fault can affect the banks unequally, and a change of learned cell may influence the comparison. The trims are clues, not proof of a failed component. Subaru diagnostic guidance on intake and upstream exhaust leaks.

Test and repair: using the vehicle and equipment procedures, the technician performs a regulated intake smoke test and finds a leak at the intake manifold seal adjoining a bank 1 runner. In this invented case the seal is replaced, and a repeat leak test shows no smoke at the repair. The leak test identifies the location; the difference in trims alone could not establish it. If no leak were found, the next checks would follow the vehicle's diagnostic procedure for bank 1 fuel delivery, exhaust and sensor circuit.

Verify: after the appropriate relearn, the technician repeats the warm closed-loop idle and raised-speed checks on both banks. At idle, bank 1 now reads LTFT +2% and STFT approximately +1%, while bank 2 reads LTFT +2% and STFT approximately 0%. The rough idle has cleared, and the code does not return during an appropriate test drive. Compare readings and monitor status with the vehicle procedure; an immediately reset LTFT is not proof of repair. A stationary 2,000 rpm check does not test fuel delivery under road load.

Worked example: misleading lambda sensor feedback

Illustrative example: a warm petrol engine with a conventional upstream narrowband sensor idles roughly and uses more fuel than expected. Closed-loop control is active. The technician records the fault codes, freeze-frame data and trims before resetting anything. The figures and test results below are invented to demonstrate the diagnosis; they are not vehicle specifications. This example assumes the manufacturer permits the trims from the same bank to be added for an approximate combined indication.

  • Bank 1 at stable idle: LTFT +12%, STFT approximately +9%; combined indication approximately +21%.
  • Upstream sensor data: the scan tool reports a low, lean-indicating signal for much of the test.
  • Independent check: a correctly used exhaust gas analyser indicates a rich exhaust under the test conditions.

Interpretation: the ECU is adding fuel because of what its feedback indicates, yet the separate exhaust measurement suggests the actual exhaust is rich. This disagreement makes the feedback path worth investigating; it does not by itself prove that the sensor is defective. Confirm the analyser setup, sampling point and interpretation for the vehicle, and investigate intake and upstream exhaust leaks, misfire and fuelling faults. Scan-tool readings are processed data and may not show every signal fault. Bosch: comparing sensor data and exhaust gas readings.

Narrowing it down: in this invented case the specified leak, combustion and fuel-system checks do not identify a fault. The technician identifies the sensor type and uses the manufacturer's test procedure, correct connections and a suitable oscilloscope to compare the sensor signal and the ECU-side input. During the prescribed response checks, the sensor-side waveform responds as expected, but the ECU-side signal is intermittently low. Inspection and circuit testing then reveal a damaged connector and wiring fault between the sensor and ECU. The disagreement localises the problem to the feedback circuit; it does not justify replacing the sensor without further evidence. A GM bulletin illustrates that contaminated oxygen-sensor wiring can skew readings on specified vehicles; its remedy is specific to those vehicles and its particular fault.

Repair and verify: the damaged wiring and connector are repaired according to the vehicle procedure, and the sensor-side and ECU-side signals are checked again. After the appropriate relearn and with closed loop confirmed, the same idle condition now shows LTFT +2% and STFT approximately +1%; the gas-analyser result is consistent with the commanded operating condition and the rough idle has cleared. The code does not return on an appropriate test drive. Compare monitor status and readings against the vehicle procedure; a recently reset LTFT alone is not proof of repair.

This example is for a conventional narrowband sensor. Wideband sensors use different control circuits and signals; never apply a generic 0–1 V test or probe an unfamiliar circuit without the manufacturer's procedure. Bosch: sensor signal types and test conditions.

Worked example: positive fuel trim under load

Illustrative example: a single-bank, port-injected petrol engine drives normally at idle but hesitates during a steady uphill drive. The technician records the complaint, any codes and freeze-frame data before resetting adaptations. The figures and test results below are invented to show the reasoning; they are not universal limits. In this example the vehicle procedure allows STFT and LTFT for the same bank to be added as an approximate combined indication.

  • Warm idle, bank 1: LTFT +2%, STFT approximately +1%; combined indication approximately +3%.
  • Steady moderate load, bank 1: LTFT +8%, STFT approximately +10%; combined indication approximately +18%. Closed-loop control remains active at the recorded point.

Interpretation: the ECU is adding much more fuel at the loaded point. A fuel supply that cannot maintain the required delivery is one possibility; inaccurate airflow measurement, injector restriction, an exhaust leak or misleading sensor feedback can also produce positive correction. Different learned cells may contribute to the change. The trim pattern alone cannot identify the defective part, and free-revving in Park does not reproduce road load.

Narrowing it down: the technician checks the vehicle's service information and inspects the intake, airflow-sensor installation, exhaust and wiring. A suitable log is captured at the moderate-load condition on a safe road or dynamometer, with a second person operating the equipment. Fuel-system status, engine speed, load, both trims, commanded and measured lambda where supported, and the relevant fuel-pressure data are recorded. The test is stopped if the engine runs severely lean or misfires; higher load or full throttle is not required to prove the point. On systems that enter open loop at high load, STFT may stop being a live correction, so interpret it only with the control status and vehicle-specific data.

Test and repair: in this example, fuel pressure is within the manufacturer's specified range at idle but falls below the required pressure during the recorded moderate-load condition. The technician confirms the measurement with the approved equipment, then follows the vehicle's fuel pressure, delivery and electrical tests. A restriction is confirmed at a serviceable fuel filter; pump supply and control test correctly. The filter is replaced and the fuel system is rechecked for leaks. A pressure drop alone would not prove the filter or pump is faulty. Bosch: fuel supply and reduced delivery.

Verify: after the appropriate relearn, the technician repeats the same warm closed-loop idle and moderate-load checks. In this example idle reads LTFT +1% and STFT approximately +1%; under the same load LTFT is +2% and STFT approximately +2%. Fuel pressure remains within the vehicle's specification, the hesitation is gone, and no relevant fault returns during the prescribed test. Check monitor status as well: an immediately reset LTFT or a short test drive alone is not proof that every monitor has completed.

Use the manufacturer's approved connections, pressure-relief steps and test equipment. Petrol direct-injection systems can retain high pressure, and their low- and high-pressure circuits require their own procedures.

Worked example: a faulty mass airflow sensor

Illustrative example: a warm, single-bank petrol engine with a mass airflow (MAF) sensor hesitates at moderate load and has a stored P0171. The technician records the codes, freeze-frame data and trims before clearing anything. The numbers and test results below are invented to show the method; they are not specifications. For this example, the vehicle procedure permits same-bank STFT and LTFT to be added as an approximate combined indication.

  • Warm idle, bank 1: LTFT +3%, STFT approximately +2%; combined indication approximately +5%.
  • Steady moderate load, bank 1: LTFT +9%, STFT approximately +10%; combined indication approximately +19%. The fuel system remains in closed loop.

Interpretation: the ECU is adding more fuel at the loaded point. A MAF sensor that under-reports airflow can contribute to a lean tendency, but these trims do not prove the sensor is faulty. Fuel delivery, unmetered air, intake configuration, exhaust leaks, sensor feedback and changes in learned cells are also possible. Closed-loop status must be checked at each point; a free-rev test in Park does not reproduce road load.

Narrowing it down: the technician follows the vehicle's diagnostic procedure, inspects the air filter, MAF housing and ducting, and checks for air leaks downstream of the MAF. Intake and upstream exhaust leak checks, fuel-pressure and delivery tests, and checks of the MAF power, ground, wiring and connector reveal no fault in this example. A low reported airflow value by itself does not establish a bad MAF: an air leak or disturbed airflow can produce misleading readings. GM: low MAF readings and intake-system causes on specified vehicles.

At the same steady speed, load and operating temperature on a dynamometer, the suspect sensor reports approximately 14 g/s; a verified compatible known-good sensor temporarily fitted in the same housing reports approximately 19 g/s. With the known-good sensor installed, the short-term correction moves towards zero while the learned long-term value initially remains positive. Reinstalling the original sensor reproduces the low reading and positive correction. The comparison supports a biased sensor after the other checks; these airflow values are illustrative and must not be used as another engine's specification. Use the manufacturer's comparison method and account for normal test variation. Subaru: P0171 metering-device and leak checks.

Repair and verify: the confirmed faulty MAF is replaced with the correct part, and the intake is reassembled and checked. After the appropriate relearn, the technician repeats the warm closed-loop idle and moderate-load checks. In this example idle shows LTFT +2% and STFT approximately +1%; at the same load LTFT is +2% and STFT approximately +2%. The hesitation has gone, and no relevant code returns during the prescribed test. Check monitor status and the manufacturer's limits; an immediately reset LTFT alone is not proof of repair. A road test requires a driver and a second person to operate the diagnostic equipment.

Worked example: a leaking fuel injector

Illustrative example: a single-bank, port-injected petrol engine has a rough idle and a difficult warm restart. The technician records the complaint, any codes, freeze-frame data and trims before clearing or resetting anything. The readings and test results below are invented to demonstrate the reasoning; they are not universal specifications. In this example the manufacturer's procedure permits same-bank STFT and LTFT to be added as an approximate combined indication.

  • Warm idle, bank 1: LTFT −12%, STFT approximately −6%; combined indication approximately −18%, with closed-loop control active.
  • Steady 2,000 rpm in Park, bank 1: LTFT −7%, STFT approximately −3%; combined indication approximately −10%, still in closed loop.

Interpretation: the ECU is removing fuel in response to feedback, suggesting a rich tendency. An injector leaking fuel is one possibility, but excessive fuel pressure, purge vapour, fuel-contaminated oil, airflow or temperature errors, and misleading lambda feedback can also cause negative correction. A misfire can leave oxygen in the exhaust and complicate the feedback, so the sign of trim alone does not prove or exclude an injector fault. The raised-speed check in Park does not reproduce road load.

Narrowing it down: the technician follows the vehicle's diagnostic procedure, checks the reported operating conditions and fuel pressure, and investigates purge flow, sensor readings and ignition. In this example those checks reveal no fault. The cylinder-specific diagnostic data points to cylinder 2, and the manufacturer's fuel-pressure retention test shows that pressure falls faster than its specification after shutdown. That result supports further testing but does not identify the leak by itself: the pump, regulator, lines, connections or other components may also cause pressure loss.

Confirm and repair: following the vehicle procedure for pressure relief and removal, the technician sends the suspect injector for an appropriate injector leak test. In this invented case it leaks from its nozzle while commanded closed, outside the tester's specification; the remaining injectors pass. Circuit checks show that the injector is not being held open electrically. The correct injector is fitted using the manufacturer's installation instructions, seals and any required coding, and the fuel system is checked for leaks. GM: injector testing to isolate a leaking injector on specified engines.

Verify: the pressure retention test is repeated and now meets the vehicle's specification. After the appropriate relearn, warm closed-loop idle shows LTFT −2% and STFT approximately −1%; at the same raised speed LTFT is −1% and STFT approximately −1%. The restart and idle concerns have cleared, and no relevant fault returns during the prescribed test. Check monitor status and inspect the oil if fuel dilution is suspected; a recently reset LTFT alone is not proof of repair.

Use approved equipment and the vehicle's fuel-pressure relief, containment and fire precautions before opening a fuel system. Petrol direct-injection systems can retain much higher pressure and require their own manufacturer-specific test and service procedures; do not transfer the port-injection method or limits to them. Bosch: petrol high-pressure injector service.

Worked example: a faulty EVAP purge valve

Illustrative example: a warm, single-bank petrol engine runs roughly at idle, particularly after refuelling. It uses a normally closed purge valve to control flow from the evaporative-emissions (EVAP) canister into the intake. The technician records any codes, freeze-frame data and trims before clearing or resetting anything. The values and results below are invented to demonstrate the reasoning; they are not universal test limits. For this example, the manufacturer permits same-bank STFT and LTFT to be added as an approximate combined indication.

  • Warm idle, bank 1: LTFT −12%, STFT approximately −6%; combined indication approximately −18%, with closed-loop control active.
  • Scan-tool data: the ECU is commanding purge closed at the recorded idle point. This is a command, not proof that the valve has sealed.

Interpretation: the ECU is removing fuel in response to feedback. Excess fuel vapour passing through a valve that is leaking when closed is one possible cause; leaking injectors, fuel pressure, fuel-contaminated oil and sensor or circuit faults are others. Purge vapour concentration varies, and unintended flow can also act as an air leak, so a purge fault does not always produce negative trim. The numbers alone cannot identify the valve.

Narrowing it down: following the vehicle-specific procedure, the technician temporarily isolates the purge path and seals the specified openings, then repeats the warm idle test in closed loop. In this invented case STFT moves from approximately −6% to +8% while LTFT remains around −12%: the approximate combined indication moves from −18% to −4%. The learned value may take time to change. This response points towards the purge path but does not prove that the valve itself is defective. The system is returned to its normal configuration after the test. GM: purge-valve checks on specified vehicles.

Confirm and repair: the technician checks the valve's control circuit and its ability to seal and open using the manufacturer's procedure and approved test equipment. In this example the control circuit tests correctly, but the disconnected, unpowered normally closed valve fails its specified sealing test and allows flow. The valve is replaced, its connections restored, and the EVAP system is checked for leaks. A valve that is being electrically commanded open, a damaged hose or another system fault needs its own diagnosis.

Verify: after the appropriate relearn, the technician repeats the same warm closed-loop idle check with the complete EVAP system connected. In this example LTFT is −2% and STFT approximately −1%; idle quality is restored and the original complaint does not recur during the prescribed test. Check fault codes and EVAP monitor status according to the vehicle procedure: a short drive may not complete the monitor, and an immediately reset LTFT is not proof of repair.

Follow the vehicle and equipment instructions when isolating or leak-testing an EVAP system. Use the specified inert gas and pressure limits for fuel-vapour testing, keep ignition sources away, and never leave the purge path disconnected or plugged after diagnosis. Bosch: fuel-system leak testing.

Worked example: exhaust leak upstream of the lambda sensor

Illustrative example: a warm petrol V-engine has an exhaust ticking noise and a stored P0171. The technician records codes, freeze-frame data and both banks' trims before clearing or resetting anything, confirms closed-loop operation and identifies each bank and upstream sensor using the vehicle information. The figures and results below are invented to show the reasoning; they are not universal limits. In this example the vehicle procedure permits STFT and LTFT from the same bank to be added as an approximate combined indication.

  • Bank 1 at stable idle: LTFT +12%, STFT approximately +8%; combined indication approximately +20%.
  • Bank 2 at the same idle: LTFT +2%, STFT approximately +1%; combined indication approximately +3%.
  • Scan-tool feedback: bank 1's upstream sensor indicates a lean tendency. The sound is most noticeable near the bank 1 exhaust manifold.

Interpretation: the ECU is adding more fuel on bank 1. A leak between that bank's cylinders and its upstream sensor may allow outside oxygen into the exhaust under some conditions; the sensor can then report a leaner mixture than the combustion alone produced. The correction and noise do not prove the leak is the cause: intake leaks, injector or fuel delivery faults, misfire and sensor or wiring faults remain possible. A leak at the sensor boss or upstream can produce a false lean indication, as described in this Toyota exhaust-leak technical tip.

Test and repair: in this invented case, intake and fuel-system checks do not identify a fault. With the engine off and exhaust cool, the technician follows the vehicle and leak-tester procedures to inspect the bank 1 manifold, joints and sensor boss. A regulated exhaust leak test reveals escaping smoke at the manifold-to-pipe joint upstream of the sensor. The faulty joint seal is replaced using the manufacturer's procedure and the exhaust test is repeated with no leak found at the repair. The smoke test identifies an outward leak at that location; the trim readings alone did not establish it. GM: exhaust leak detection guidance for specified vehicles.

Verify: after the appropriate relearn, the technician repeats the same warm closed-loop idle check on both banks. In this example bank 1 now reads LTFT +2% and STFT approximately +1%; bank 2 reads LTFT +2% and STFT approximately 0%. The ticking has stopped and no relevant fault returns during the prescribed test. Compare readings and monitor status with the vehicle's procedure; an immediately reset LTFT is not proof of repair, and the sensor should not be replaced merely because the code or feedback appeared lean.

Use the manufacturer's approved leak-test equipment and pressure limits. Keep clear of hot exhaust components and ensure exhaust gases are safely extracted when the engine runs.

Common fault codes

P0171 and P0172 generally identify a lean and a rich fuel-system condition on bank 1; P0174 and P0175 identify lean and rich conditions on bank 2 respectively. The code indicates the monitor result, not the failed component. Confirm the exact description and diagnostic procedure for the vehicle, including its bank identification. Monitor thresholds and enabling conditions vary. Toyota: fuel-trim code examples.

Workshop procedure

  1. Record the complaint, fuel type, modifications, stored and pending codes, freeze-frame data and readiness. Inspect intake ducting, hoses, PCV connections, wiring and exhaust for obvious faults. Do not clear codes or adaptations before recording the evidence.
  2. Bring the engine to the relevant temperature and verify fuel-control status. Log STFT and LTFT for each available bank, engine speed, load, coolant temperature, airflow or manifold pressure, commanded lambda and upstream sensor data where supported.
  3. Record a stable idle, then a stable raised speed in a safe stationary position, following the vehicle procedure. Compare the same bank and operating conditions. If the concern occurs under load, capture a suitable road or dynamometer log safely with a second person operating the scan tool.
  4. Use the pattern to select a test: a regulated smoke test for an intake leak, fuel pressure and delivery tests under the specified conditions, injector tests, or checks of airflow and sensor wiring. Follow vehicle and equipment procedures for pressure and test medium; do not apply unregulated shop air to the crankcase or fuel system. For fuel-vapour systems, use the specified inert gas and leak-test equipment. Petrol direct-injection systems can retain high pressure: follow the manufacturer’s depressurisation and connection procedure before opening a fuel circuit. Bosch: leak testing and inert gas.
  5. If sensor feedback and other evidence disagree, compare with an exhaust gas analyser and test the sensor and circuit using the correct procedure. Scan-tool values are processed and may be limited or filtered; a suitable oscilloscope can reveal a signal the displayed data does not show. Check the circuit, reference and heater as applicable before replacing parts.
  6. Repair the confirmed cause, then follow the manufacturer's instructions for clearing faults or resetting adaptations if appropriate. Recheck for leaks, repeat the original operating conditions and allow the ECU to relearn before judging the final result.

When feedback tells the wrong story

A positive trim means the ECU is adding fuel; it does not independently prove that the actual exhaust mixture is lean. An exhaust leak upstream of the sensor, misfire, wiring fault or a faulty sensor can distort the oxygen signal. If a gas analyser indicates a rich exhaust while the ECU is adding fuel, investigate the feedback and its circuit as well as the fuelling system. A newly fitted sensor or other part still needs to be tested. Bosch recommends comparing sensor data with exhaust-gas readings and, where necessary, checking the signal with an oscilloscope. Bosch: lambda and air-mass sensor diagnosis.

A conventional narrowband zirconia sensor and a wideband air–fuel sensor have different signals and test methods. Do not apply a 0–1 V switching test to every sensor; use the manufacturer's pinout, equipment and procedure. Exhaust oxygen can also be affected by misfire, so interpret the signal alongside combustion and gas-analysis evidence. Bosch: lambda sensor signal types.

Related reading