Tuning Wiki

Crankcase ventilation removes gases that leak past the piston rings into the engine crankcase. A closed positive crankcase ventilation (PCV) system routes these gases back to the engine intake instead of venting them to the atmosphere. It also manages crankcase pressure and separates oil from the vapour stream. The actual plumbing, pressure-control method and diagnostic limits depend on the engine.

This guide covers PCV operation and faults. See petrol and diesel emissions, EVAP systems and charcoal canisters, carbon deposits and cleaning and lambda sensor diagnosis. EVAP collects fuel-tank vapour; PCV handles crankcase gases. They may share an intake connection but are separate systems.

Blow-by and why ventilation is needed

During combustion, some gas passes the piston rings into the crankcase even in a serviceable engine. This blow-by contains combustion products and unburned fuel; the crankcase stream can also carry oil droplets and water vapour. Ring sealing, cylinder condition, engine load and temperature affect the amount. If the gases cannot leave, pressure can rise and force oil past seals; if routed directly to the atmosphere they contribute to hydrocarbon emissions. A ventilation system moves them away and manages pressure while limiting the oil carried into the intake. US EPA light-duty emissions report, section 6; Motorservice: crankcase pressure and turbocharger oil leakage.

Earlier road-draft or open breather arrangements could discharge crankcase gases to ambient air. A closed system returns the gases to the intake so they can be burned; a fresh-air path may supply replacement air. The EPA's historic PCV training guide describes open and closed US vehicle layouts. Those historical US designs and dates do not identify the equipment on a particular UK vehicle. Diesel and heavy-duty arrangements have also varied, including open ventilation with separated or treated gases; do not assume every diesel has a petrol-style PCV valve. US EPA heavy-duty engine rule, crankcase emissions discussion.

Typical components and flow

One common closed-system path is filtered intake air → crankcase and rocker cover → oil separator / pressure control → metered connection to the intake → combustion. This is a conceptual route, not a hose diagram for every engine. The system is connected to the engine's air metering and must be considered when diagnosing mixture. Some designs integrate several functions into the valve cover, while others have separate hoses, filters and valves.

PartFunctionWhat varies
Breather and fresh-air pathAllows the required air and gas movement between intake and crankcase.Location, filtered-air source, ports and flow direction depend on design and operating state.
PCV metering valve or calibrated restrictionControls flow into the intake, helping avoid excessive unmetered airflow.May be a replaceable spring-and-plunger valve, an integrated diaphragm, or a different control mechanism. Not every engine has a replaceable rattling valve.
Oil separator, baffles or cycloneSeparates entrained oil before the gases re-enter the intake; collected oil is returned or retained according to the design.Some use baffles or cyclones, others serviceable coalescing filters. Return channels, valves and service intervals differ.
Pressure regulator and non-return valvesManage pressure or route flow and restrict reverse flow where required.Often integrated with the separator or valve cover. Fitment and normal state are engine-specific.
Hoses, ports and sealsCarry the gases and maintain a controlled path.Hoses, diaphragm seals, connections and oil-return passages can split, harden, block or leak.

The Audi EA855 EVO 2.5 TFSI training document, pages 20–26, is one documented integrated system: it shows coarse baffles, a cyclone separator, oil returns, diaphragm pressure control and non-return valves. This is an example, not a universal layout. MANN+HUMMEL's ProVent manual illustrates another separator and its manufacturer-specified maintenance.

PCV metering and changing engine load

On a conventional older petrol engine, manifold vacuum draws gas from the crankcase through a metering valve. In the spring-and-plunger example in the EPA guide, high intake vacuum at idle moves the valve to a position with a small flow passage. At a different vacuum the plunger moves and allows a different flow; the valve also closes against reverse pressure in the described backfire condition. This describes that valve design, not every modern diaphragm or electronically managed system. The valve does not have to be visibly opening and closing in the same way on every engine. EPA PCV training guide, valve operation.

On a turbocharged petrol engine, the manifold may be under vacuum at light load but under positive boost at another operating point. Many designs therefore use non-return valves and more than one route: when suitable, gases can flow to the manifold; under boost a separate path to the compressor inlet can provide a pressure difference. Check valves help prevent boost entering a path intended for suction. The Audi example routes gas to the intake ports or turbocharger inlet according to pressure conditions. Actual placement, fresh-air supply and control are model-specific; do not infer hose direction from this example. A naturally aspirated engine or diesel can use a different pressure-control arrangement. Audi EA855 EVO, PCV and separator.

Another documented arrangement is MAHLE's example for certain Volkswagen Group 1.8 and 2.0 TFSI engines: the ventilation path changes between intake-manifold vacuum and boosted operation, and a damaged diaphragm can allow unwanted pressure into the crankcase. Treat this as an example to investigate using the exact engine's routing and test procedure. MAHLE Technical Messenger 07/2017.

Oil separation, water and deposits

A baffle changes gas direction so larger droplets can separate. A cyclone uses a swirling flow to help separate finer oil droplets; a coalescing element can capture and combine droplets in designs that use one. Separated oil may drain back to the engine through a dedicated path or be collected for service, depending on the assembly. An obstructed drain, damaged diaphragm, blocked element or incorrect installation can affect operation. Do not assume a filter is serviceable simply because a similar system uses a replaceable element. Audi separator description; MANN+HUMMEL installation and maintenance manual.

Oil vapour and droplets can form deposits in intake plumbing; exhaust-gas recirculation can add soot where the streams meet. Deposit severity varies and deposits alone do not prove a separator fault. Water vapour can condense as the engine cools, particularly with short trips and cold conditions. Cream-coloured deposits are a reason to investigate, but they do not by themselves prove a head-gasket or coolant leak. Compare coolant level, oil condition and the manufacturer's checks. See carbon deposits and cleaning.

Faults and symptoms

Observation or faultPossible effectsCheck before deciding
Blocked or restricted breather, separator, hose or oil returnCrankcase pressure may rise; oil leaks, oil carryover or poor drain-back can follow.Inspect the full gas and oil-return paths; excessive blow-by from engine wear or another obstruction can produce similar pressure.
Leaking diaphragm, hose or stuck valveAn unintended intake leak can disturb idle, fuel trims or mixture control, depending on the design and location.Use the correct layout and the maker's leak-test and pressure procedure. A lean code is not proof of a PCV fault.
Failed non-return valve or wrong hose routing on a boosted engineUnwanted pressure or flow in a PCV path, oil leakage or drivability issues can result.Identify the intended connections and flow direction; check components using the specified procedure.
Excess oil in intake or exhaustOil carryover can result from failed separation or high crankcase pressure, among other causes.Check oil level, separator and drains, turbo oil supply/return and condition, valve seals and engine condition before replacing a turbocharger.
Noise, idle change or oil-cap suctionWhistling or unusual suction can accompany a diaphragm or pressure-control problem.A cap or glove observation alone is not a measured pressure or diagnosis. Compare a suitable gauge reading with the vehicle procedure.

A blocked ventilation system and excess mechanical blow-by are different faults and can coexist. Excessive crankcase pressure can impair turbocharger oil drainage, so an oily turbocharger alone does not establish that the turbo is the root cause. Motorservice: turbocharger oil leakage and crankcase pressure.

Diagnostic sequence

  1. Identify the engine and system. Obtain the routing diagram, technical bulletins, specified pressure test point, operating conditions, oil specification and relevant service history. Record symptoms, oil consumption, leaks, fault codes and freeze-frame data before clearing anything.
  2. Inspect with the engine off. Check oil level and obvious damage, hose routing and connections, cracked pipes, collapsed hoses, disconnected breathers, separator, wiring where fitted, signs of blockage and external leaks. Do not dismantle hot parts.
  3. Check mixture and related systems. With an appropriate scan tool, compare fuel trims, airflow and faults at the specified conditions. A damaged PCV hose or diaphragm can behave like an intake leak, but trim direction depends on the air path and system. Check other air leaks and fuelling causes too. See lambda sensor diagnosis.
  4. Measure crankcase pressure properly. Use the manufacturer-approved connection, gauge or manometer, and procedure, with the engine in the specified state. Read the scale and sign: gauge pressure is relative to atmospheric pressure; a vacuum may be shown as a negative gauge pressure or as a positive vacuum magnitude. Compare like units and the specified test conditions. There is no universal PCV pressure or idle vacuum specification for all engines.
  5. Separate causes. Investigate the complete breather path, separator, drain and non-return valves before concluding that pressure proves worn rings. Where the manufacturer calls for it, use a suitable blow-by flow measurement, compression or cylinder leak-down test to investigate engine sealing. A pressure reading alone is not a direct measurement of blow-by flow and does not identify the failed part. BMW crankcase-pressure diagnostic bulletin.
  6. Use the correct leak-test method. Follow the vehicle maker’s smoke-test instructions and isolation requirements; do not pressurise the crankcase as a generic intake smoke test. Audi’s intake leak-test bulletin gives an example of isolating crankcase ventilation to prevent oil being forced into the intake.
  7. Repair and verify. Fit the correct components and seals, restore the intended routes, follow the specified replacement or filter service and confirm the original fault, pressure and any relevant codes or leaks under the prescribed conditions. Do not clear a fault or reset an adaptation as a substitute for repair.

Use suitable exhaust extraction during running tests and keep hands, clothing and equipment away from belts, fans and hot exhaust parts. Allow the engine to cool as appropriate and follow the manufacturer's instructions for opening or testing the system. HSE: vehicle exhaust emissions.

Catch cans and modifications

Some aftermarket oil separators or catch cans are fitted in crankcase ventilation plumbing. Their performance depends on the design, installation, flow capacity, drain and temperature conditions. If used, they must suit the engine's actual flow and pressure-control system; an obstructed hose, frozen condensate, incorrect drain or removed check valve can make matters worse. A can is not automatically equivalent to the original separator or a cure for worn rings. Follow the supplier's and vehicle maker's instructions and applicable requirements. MANN+HUMMEL: separator installation and service example.

UK MOT context

The DVSA MOT manual, section 8 sets the applicable emissions, malfunction indicator and fluid-leak checks for cars and light commercial vehicles. A serious oil leak or an emissions defect may be relevant under the applicable inspection criteria. Do not assume a routine MOT includes a dedicated PCV flow or crankcase-pressure test. Consult the current manual and identify the vehicle class; a tailpipe pass does not prove the crankcase system is working correctly.

Sources and further reading