Tuning Wiki

An evaporative emissions control system, usually called EVAP, captures fuel vapour that would otherwise escape from a petrol vehicle's fuel system. The charcoal canister stores hydrocarbons temporarily; when operating conditions allow, the engine draws fresh air through the canister and burns the released vapour. EVAP addresses vapour from the tank and fuel system, including while the engine is stopped. It is separate from exhaust aftertreatment and crankcase ventilation.

System layouts, monitoring and legal requirements differ by vehicle and market. For the wider context see petrol and diesel emissions, lambda sensors, AFR and lambda and ME7 fuel trim learning and purge states.

Where fuel vapour comes from

Petrol is volatile. Vapour forms in the tank as fuel warms and the vehicle is driven or parked; temperature changes can make the tank breathe in and out. Hot-soak losses can occur after shutdown, and vapour is displaced when fuel is added. The size of these losses depends on fuel properties, temperature, vehicle design and system condition. The US EPA evaporative emissions report distinguishes diurnal, running, hot-soak and refuelling emissions.

Onboard refuelling vapour recovery (ORVR), where fitted and required in the vehicle's market, directs displaced refuelling vapour into the vehicle's canister rather than simply venting it. Tank valves and filler arrangements vary. An ORVR description in US regulatory material is not proof that a particular UK or European vehicle has the same layout or monitoring. US EPA draft regulatory impact analysis.

The canister: storage and purge

Activated carbon has a large internal surface area. Hydrocarbon molecules adsorb onto that surface as tank vapour passes through the canister. During a purge, air drawn through the carbon helps the stored hydrocarbons desorb and travel to the engine. This is a repeated storage-and-release process; the canister is not a disposable filter that normally fills up after a fixed number of journeys. Capacity, vapour loading, temperature and purge conditions affect performance. EPA: evaporative control technology; HELLA: activated charcoal canister.

A simplified, common layout is tank vapour space → vapour lines and separation valves → charcoal canister → purge valve → engine intake. Fresh air enters through a canister vent during purge. An electrically controlled vent valve or leak-detection device may be fitted in some systems. The arrows show the purge route, not a vehicle-specific hose diagram: tank venting, refuelling and diagnostic tests can use different flow paths.

ComponentPurpose and checks
Tank, filler and cap or capless sealContain the fuel and vapour. Caps and capless systems use different seals and procedures. A damaged or incorrectly fitted seal can cause a leak or fault on a monitored system.
Vapour lines, separator and rollover or shut-off valvesRoute vapour while limiting liquid fuel entering vapour plumbing under the relevant conditions. Inspect the actual hoses and fittings; a valve can be integrated into the tank or another component.
Activated-carbon canister and fresh-air ventStore and release vapour. A damaged casing, blocked vent or contaminated carbon can affect operation. Fittings and location vary by vehicle.
Purge control valve or solenoidRegulates the path between the canister and intake. The ECU may pulse it to meter flow. Electrical actuation does not prove that it seals or flows correctly.
Vent or canister close valve, where fittedControls the fresh-air side on systems that use it, including closing the path for some leak tests. It is a different component from the purge valve.
Fuel tank pressure sensor, switch or leak-detection pump, where fittedProvides pressure information or assists a system-specific leak monitor. The presence and operation of each device depend on the vehicle.

HELLA describes a common arrangement in which the purge valve opens a path to intake vacuum under suitable conditions; the ECU controls the vapour delivery because it affects mixture. HELLA, functional principle and diagnosis.

ECU control, mixture and fuel trims

Purge is metered because the amount of stored fuel in the airflow changes as the canister empties and conditions change. Engine temperature, load and the available pressure difference can affect the strategy; purge may be inhibited at particular operating points. Some turbocharged engines use additional routing, check valves or other arrangements when the usual intake connection is pressurised. Use the vehicle diagram rather than assuming that every purge valve connects to the same location.

On a petrol engine with oxygen feedback, the ECU can adjust fuelling as vapour enters the intake. A purge valve leaking when it should be closed can introduce unintended air or fuel vapour and disturb idle and fuel trims; the direction of the correction depends on the vapour concentration and system layout. A rich or lean trim is a clue, not proof of a purge fault. Compare commanded purge, trims and running condition using the manufacturer's test and take intake leaks, fuel delivery and other faults into account. See ME7 fuel-trim learning and purge states for an ECU-specific example.

How leak and purge monitoring works

Some vehicles monitor purge flow and look for leaks using a tank pressure sensor, a vent valve and controlled vacuum; others use a leak-detection pump, a pressure switch or pressure changes as the tank cools after shutdown. They do not all use the same hardware or run the test at the same time. Monitors may require particular fuel level, temperatures, soak time, vehicle speed or other conditions. An incomplete or not-ready monitor means the required test has not finished; it is not itself a diagnosed leak or proof the system has passed.

For one documented example, Ford describes a monitor that applies engine vacuum, closes valves and evaluates the pressure change under defined entry conditions. Its published diagnostics also describe an engine-off natural-vacuum approach. These are examples, not universal test procedures or leak thresholds. Ford 2015 OBD system operation; Ford 2016 OBD system operation.

Codes such as P0441 for purge-flow performance, P0442 for a small leak and P0455 for a large leak are examples of generic EVAP descriptions. Manufacturer definitions, monitor thresholds and conditions must be checked for the vehicle. A leak code describes the monitor result, not a confirmed component; an incorrectly sealed cap, a leaking line, a valve that fails to seal or a pressure-measurement fault can lead to further investigation. Some vehicles have no conventional removable fuel cap. Ford OBD examples; HELLA EVAP diagnosis.

Common faults and symptoms

FaultPossible result and what to check
Purge valve stuck closed, restricted or disconnectedInsufficient flow when commanded, a fault code and reduced canister purging. Check the supply, control, valve and pipework; a commanded duty cycle alone does not establish flow.
Purge valve leaking or stuck openUncommanded vapour or air can upset mixture, idle or restarting after refuelling on some vehicles. Check that it seals and responds under the specified conditions.
Leak at tank, filler, cap, hose or connectionFuel smell or a monitored leak. Vapour may escape without a visible liquid leak. Check the exact seal and accessible connections; do not assume the cap is the cause.
Restricted vent, vent valve or kinked lineTank pressure control or refuelling can be affected. Repeated nozzle shut-off has other possible causes, including filler and tank faults; follow the vehicle test.
Damaged or liquid-fuel-contaminated canisterVapour storage and airflow can be impaired; carbon fragments may contaminate lines. Investigate the tank vent, separator and fill history as well as the canister.
Sensor, wiring or monitor faultImplausible tank pressure or failed leak-test criteria. Check electrical supply, ground, signal, reference and operating conditions before replacing a sensor.

Fuel odour can indicate a vapour leak, but liquid-fuel leaks and other sources must also be checked. Treat an active fuel leak or strong odour as a repair priority; avoid ignition sources and follow workshop fuel-handling procedures.

Workshop diagnosis and service

  1. Identify the system. Record the vehicle, engine, fuel, market, fault codes, freeze-frame data and fuel level. Obtain the correct routing diagram and service information; note whether it has a vent valve, pressure sensor, leak-detection pump and a conventional cap.
  2. Inspect safely. Check visible filler seals, hoses, connectors and canister damage, displaced pipes, trapped lines and fuel leaks. Inspect electrical connections, supply and ground where relevant. Correct obvious damage before running further tests.
  3. Establish conditions. Compare requested purge and reported values, engine temperature, trim and tank pressure under the manufacturer's specified conditions. A valve can be electrically operated yet mechanically stuck or leaking. Follow the specified test for sealing and flow; do not use arbitrary voltage, pressure or vacuum values.
  4. Test for leaks with the correct equipment. Where the manufacturer specifies an EVAP-rated smoke or leak tester, use its approved connection, test medium, pressure limit and valve commands for that vehicle. Some systems require a specified inert gas: follow the vehicle and equipment instructions. Do not apply unrestricted compressed air or a generic intake smoke-test pressure to the tank. Fuel vapours are flammable; control ignition sources and provide suitable ventilation. See HSE guidance on petrol in motor vehicle repair. Ford's EVAP leak-test bulletin illustrates one equipment-specific procedure, not a universal method.
  5. Repair the cause and verify. Fit the correct hoses, seals or components, reconnect the system and run the specified tests and monitor when its entry conditions can be met. Clearing a code or disconnecting the battery does not repair a leak, and readiness may take time to complete.

Do not block a tank vent, blow through a canister with workshop air, dry or heat a fuel-contaminated assembly, or wash it with solvents unless the vehicle manufacturer's procedure explicitly calls for that operation. Canister serviceability and replacement instructions differ. Find and correct the reason for liquid-fuel contamination or charcoal damage; a replacement can suffer the same problem if the cause remains.

UK MOT and emissions testing

The DVSA inspection manual, section 6 specifies relevant fuel-system, leak and filler-cap checks; section 8 sets out emissions and malfunction-indicator checks for applicable vehicles. Consult the current manual and vehicle class. Do not assume that a routine UK MOT includes a dedicated EVAP leak test or OBD readiness check. A tailpipe gas-analyser result does not measure vapour escaping from the parked vehicle.

Sources and further reading