Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Diagnostics
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Fuel trims show how much an engine control unit (ECU) is correcting its calculated fuel delivery in response to exhaust oxygen feedback. They are useful diagnostic clues even when no fault code is stored. This guide focuses on closed-loop petrol engines; diesel, lean-burn and some direct-injection strategies use different controls and displays.

How the feedback loop works

The ECU calculates a base fuel quantity from measured or estimated air and operating conditions. When the system enters closed loop, it compares exhaust sensor feedback with the commanded mixture and adjusts fuelling. For conventional petrol at stoichiometry, lambda is 1; the familiar approximately 14.7:1 air-to-fuel ratio is an approximation and changes with fuel composition. Other operating conditions may call for a different mixture.

1. Calculate2. Deliver3. Measure4. Correct
Air, speed, temperature and load → base fuelInjectors deliver fuel → combustionUpstream lambda sensor measures exhaust oxygenECU compares feedback with target → adjusts fuel and repeats

Diagram: simplified closed-loop fuel control. The exact inputs and control strategy depend on the vehicle. US EPA: fuel system trim and feedback.

Short-term and long-term trim

  • Short-term fuel trim (STFT) is the faster feedback correction. It changes as the ECU responds to the sensor and operating conditions.
  • Long-term fuel trim (LTFT) is a learned correction that can take over a persistent adjustment, leaving STFT room to respond. Some ECUs learn separate corrections for idle, part load and other operating regions.
DisplayWhat the ECU is doingWhat it suggests
Positive percentageAdding fuel relative to its base calculationFeedback indicates a lean tendency, or feedback is misleading
Negative percentageRemoving fuel relative to its base calculationFeedback indicates a rich tendency, or feedback is misleading
Near zeroLittle correction in that operating regionNot proof that every sensor or operating condition is healthy

Some manufacturer-specific data uses a multiplier or a different name instead of a percentage: for example, 1.00 may mean no correction. Do not confuse that correction factor with lambda 1.00. Check the data definition for the vehicle. Manufacturer explanation of fuel corrections and learning.

On systems where the manufacturer specifies it, STFT and LTFT for the same bank can be added as a useful approximate indication of total correction. For example, +12% LTFT and −3% STFT suggest approximately +9% overall. It is a diagnostic approximation, not a universal formula for exact injector pulse width. A small STFT alone can hide a large learned LTFT. Compare with the manufacturer's method, limits and conditions.

Reading the pattern

Observed patternPossible direction for testing
Positive at warm idle, closer to zero at a steady raised speedInvestigate an intake or crankcase ventilation leak; airflow measurement and other faults can produce similar results.
Positive at idle and under load, or increasingly positive under loadCheck fuel delivery and pressure under the specified conditions, air measurement, injectors and exhaust leaks. A stationary raised-speed test is not a substitute for a load test.
Negative in several operating regionsInvestigate excess fuel, purge flow, fuel pressure, injector leakage or a biased sensor/input, according to the vehicle's test plan.
One bank differs from the otherCompare bank-specific intake and exhaust leaks, injectors and sensor circuits. A shared fault can still affect banks differently.
Large corrections but no codeRecord the evidence and investigate; a fault may not have met its monitor conditions or threshold.

These are hypotheses, not component verdicts. For example, a fixed air leak often has a greater proportionate effect at idle, but different airflow models and faults can change the pattern. A GM service procedure for specific vehicles compares idle and approximately 2,000 rpm and lists several possible causes when trim improves; it does not establish a universal limit. GM service information.

Workshop procedure

  1. Record the complaint, fuel type, modifications, stored and pending codes, freeze-frame data and readiness. Inspect intake ducting, hoses, PCV connections, wiring and exhaust for obvious faults. Do not clear codes or adaptations before recording the evidence.
  2. Bring the engine to the relevant temperature and verify fuel-control status. Log STFT and LTFT for each available bank, engine speed, load, coolant temperature, airflow or manifold pressure, commanded lambda and upstream sensor data where supported.
  3. Record a stable idle, then a stable raised speed in a safe stationary position, following the vehicle procedure. Compare the same bank and operating conditions. If the concern occurs under load, capture a suitable road or dynamometer log safely with a second person operating the scan tool.
  4. Use the pattern to select a test: a regulated smoke test for an intake leak, fuel pressure and delivery tests under the specified conditions, injector tests, or checks of airflow and sensor wiring. Follow vehicle and test-equipment procedures; do not apply unregulated shop air to the crankcase or fuel system.
  5. If sensor feedback and other evidence disagree, compare with an exhaust gas analyser and test the sensor and circuit using the correct procedure. Scan-tool values are processed and may be limited or filtered; a suitable oscilloscope can reveal a signal the displayed data does not show. Check the circuit, reference and heater as applicable before replacing parts.
  6. Repair the confirmed cause, then follow the manufacturer's instructions for clearing faults or resetting adaptations if appropriate. Recheck for leaks, repeat the original operating conditions and allow the ECU to relearn before judging the final result.

When feedback tells the wrong story

A positive trim means the ECU is adding fuel; it does not independently prove that the actual exhaust mixture is lean. An exhaust leak upstream of the sensor, misfire, wiring fault or a faulty sensor can distort the oxygen signal. If a gas analyser indicates a rich exhaust while the ECU is adding fuel, investigate the feedback and its circuit as well as the fuelling system. A newly fitted sensor or other part still needs to be tested. Bosch recommends comparing sensor data with exhaust-gas readings and, where necessary, checking the signal with an oscilloscope. Bosch: lambda and air-mass sensor diagnosis.

A conventional narrowband zirconia sensor and a wideband air–fuel sensor have different signals and test methods. Do not apply a 0–1 V switching test to every sensor; use the manufacturer's pinout, equipment and procedure. Exhaust oxygen can also be affected by misfire, so interpret the signal alongside combustion and gas-analysis evidence. Bosch: lambda sensor signal types.

Related reading