Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Switchable maps
Parent
Simos 18
Applies to
Simos 18.1
Tool groups
None
Manufacturers
Volkswagen Group

Changes from revision 6 to revision 6

Removed text is struck through; added text is highlighted.

What is being switched?

Scope: These are documented or community-definition examples, not a universal map list for every Simos 18. Check the exact ECU, ASW, CAL, gearbox, patch and definition revision. Names, available functions, axis scaling, selectors and addresses vary. A calibration value or logger signal is not automatically a safe setting. None of the examples is a ready-made tune.

Some multi-map patches replicate selected maps or add per-slot modifiers in one ECU image. A selection changes the configured parameters; it is not necessarily a complete original-versus-tuned flash. A drive-mode button by itself does not establish that such a patch is present. The THANAS MQB description explicitly describes replicated calibration tables.

Switchleg S50 Switch Patch 29.33 V2: definition names

The pinned Switchleg1 S50 Switch Patch 29.33 V2 XDF is a patch-specific TunerPro definition titled SC8S50. Verify the exact ASW and matching patch before using it. Its five slot groups include the labels below. These are XDF display names supplied with that patch, not universal OEM Simos function identifiers. A title in an XDF does not alone prove the implementation or axes.

Torque Request AT Type 1/2/3; Torque Request MT Type 1/2: per-slot torque request groups as named in this XDF. Check gearbox selection and the actual request and limiting chain.PUT setpoint: a per-slot pressure-related map labelled in hPa. The published XDF has generic axis descriptors, so confirm the patch's inputs and meaning rather than assuming it is a boost cap.Spark modifier; Lambda modifier: per-slot modifiers. Confirm how and when each is applied in the corresponding patch documentation and log the result.RPM limiter; Speed limiter; Pops enable: per-slot labels for limiter and sound selection.Manual AFU: a manual ethanol-related value; the XDF description says changing this value does not by itself activate manual AFU.Enable flex fuel spark/PUT/lambda/TQ/IAT/MPI modifier; Enable RAL; Enable NLS; Enable LC: feature-enable labels. Their presence in a definition does not prove a feature is activated in a given file.

The same XDF names a UI button selector for cruise cancel, cruise resume, variable-speed setpoint or pedals. These are definition labels, not a promise that every vehicle supports each input. Confirm the patch, input configuration and active slot. Displayed labels and map addresses must not be transferred to other patch revisions.

simos.app Main Patch: a different implementation

The simos.app Main Patch documentation describes two to five selectable slots. Its own labels include Torque Limit AT, Torque Limit MT, Torque Limit ECO, Boost limit by rpm and gear, Spark offset, Rev limit, Pops & bangs, Pops duration and Pops intensity. The boost limit is the lower of the OEM setpoint and the slot ceiling; it does not raise the OEM setpoint. The slot rev limit can lower the OEM limit. These are product-specific semantics, not the same thing as Switchleg's similarly named PUT setpoint.

The documented input options include configured cruise buttons, Start/Stop, ESC, a standstill indicator sequence and drive-mode association; availability and side effects depend on configuration. The vendor says its Start/Stop and ESC inputs retain their ordinary function. Its patch documentation requires a full flash to add or remove the patch and a calibration flash for later parameter edits; use the installed product's own instructions.

Selection, startup and shared axes in the Main Patch

The Main Patch guide distinguishes opening the selection display from committing the selected slot. With its documented default cruise-button assignment, holding the assigned button opens selection, up/down step through the slots, and SET commits immediately; otherwise the configured selection window commits the displayed slot after inactivity. A zero hold-time or window setting uses the vendor's stated defaults rather than an instantaneous action. Verify the installed assignment and patch version before interpreting the tachometer display.

Map at engine start can restore the last active slot or select a configured slot. Map follows drive mode, when enabled, maps each supported profile to a slot or to “No change”; in Eco the documented patch selects the slot's ECO torque limit. A remembered slot, a drive-mode selection and a button press are distinct inputs. The optional Start/Stop lamp takeover changes its indication while selection is open; the guide says button presses still reach the original Start/Stop function. Its ESC double-tap selection also performs the vehicle's ordinary ESC-button action, so the resulting traction state needs to be checked.

The documented Boost limit by rpm and gear is absolute hPa. Row 0 denotes neutral and row 1 first gear; higher gears use the last specified row, and the previous gear is held during a shift. Its ceiling does not establish measured manifold pressure or cancel other protections. Boost-limit rpm and spark-offset rpm/load axes are shared across slots. The guide also notes that selecting a lower per-slot rev threshold while engine speed is already above it can immediately invoke the limiter. These are properties of this implementation, not universal Simos 18 rules.

The vendor describes a VIN-fingerprint check: on mismatch, its boost limit, spark offset, flex-fuel, pops, RAL and launch features revert to their stock behaviour. That statement applies to the features listed by this patch's guide and does not prove that every calibration, fault response or other patch is unchanged. Confirm ECU identity and the installed software when a selected feature does not behave as expected.

Other mode systems and fuel

EcuTek RaceROM for EA888 documents four switch modes and its own per-mode torque, boost, ignition and lambda features. Its Boost Target Max Map Switch modes 1–4 are pressure-target ceilings; separate per-gear, per-mode torque-demand and reference-air-charge limits are also described. A ceiling is not a command to attain that pressure or torque. The guide documents per-mode full-load lambda targets and RaceROM part-load GDI/MPI lambda maps that replace corresponding OEM maps when the feature is used.

For ignition, the same guide describes mode-specific lift and no-lift RaceROM base maps, while OEM idle and flap-closed maps remain relevant in its described implementation. Final ignition is still subject to knock and other corrections. Check the installed feature and active path; changing a table that is bypassed in a given mode will not necessarily change the output. Its three-button stalk procedure cannot switch while rolling; the steering-wheel and multi-axis-stalk procedures use different inputs. These behaviours are product-specific and must not be assumed for another patch.

Manual fuel-map selection and sensor-based flex fuel are different. Confirm the fuel, active slot and actual ethanol source and blending configuration; selecting an ethanol-labelled slot does not measure fuel content.

Related: switchable maps · pops and bangs · crackle tuning · DSG shift sounds.

Launch and rolling anti-lag switches are implementation-specific. For the Main Patch and other examples, see the separate launch-control and rolling anti-lag guides, including their different gating and timeout behaviours.

Separate guides: traction control tuning · flat-foot shifting.

For the separate OEM and patch paths, see rev limiter tuning and vehicle-speed limiter tuning.

Source notes

Patch definition and supplier documentation reviewed 17 November 2026. Do not assume a listed label is present in every S50 revision or use generic XDF axis labels as proof of the underlying variables.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 6: Simos 18 switchable maps

What is being switched?

Scope: These are documented or community-definition examples, not a universal map list for every Simos 18. Check the exact ECU, ASW, CAL, gearbox, patch and definition revision. Names, available functions, axis scaling, selectors and addresses vary. A calibration value or logger signal is not automatically a safe setting. None of the examples is a ready-made tune.

Some multi-map patches replicate selected maps or add per-slot modifiers in one ECU image. A selection changes the configured parameters; it is not necessarily a complete original-versus-tuned flash. A drive-mode button by itself does not establish that such a patch is present. The THANAS MQB description explicitly describes replicated calibration tables.

Switchleg S50 Switch Patch 29.33 V2: definition names

The pinned Switchleg1 S50 Switch Patch 29.33 V2 XDF is a patch-specific TunerPro definition titled SC8S50. Verify the exact ASW and matching patch before using it. Its five slot groups include the labels below. These are XDF display names supplied with that patch, not universal OEM Simos function identifiers. A title in an XDF does not alone prove the implementation or axes.

  • Torque Request AT Type 1/2/3; Torque Request MT Type 1/2: per-slot torque request groups as named in this XDF. Check gearbox selection and the actual request and limiting chain.
  • PUT setpoint: a per-slot pressure-related map labelled in hPa. The published XDF has generic axis descriptors, so confirm the patch's inputs and meaning rather than assuming it is a boost cap.
  • Spark modifier; Lambda modifier: per-slot modifiers. Confirm how and when each is applied in the corresponding patch documentation and log the result.
  • RPM limiter; Speed limiter; Pops enable: per-slot labels for limiter and sound selection.
  • Manual AFU: a manual ethanol-related value; the XDF description says changing this value does not by itself activate manual AFU.
  • Enable flex fuel spark/PUT/lambda/TQ/IAT/MPI modifier; Enable RAL; Enable NLS; Enable LC: feature-enable labels. Their presence in a definition does not prove a feature is activated in a given file.

The same XDF names a UI button selector for cruise cancel, cruise resume, variable-speed setpoint or pedals. These are definition labels, not a promise that every vehicle supports each input. Confirm the patch, input configuration and active slot. Displayed labels and map addresses must not be transferred to other patch revisions.

simos.app Main Patch: a different implementation

The simos.app Main Patch documentation describes two to five selectable slots. Its own labels include Torque Limit AT, Torque Limit MT, Torque Limit ECO, Boost limit by rpm and gear, Spark offset, Rev limit, Pops & bangs, Pops duration and Pops intensity. The boost limit is the lower of the OEM setpoint and the slot ceiling; it does not raise the OEM setpoint. The slot rev limit can lower the OEM limit. These are product-specific semantics, not the same thing as Switchleg's similarly named PUT setpoint.

The documented input options include configured cruise buttons, Start/Stop, ESC, a standstill indicator sequence and drive-mode association; availability and side effects depend on configuration. The vendor says its Start/Stop and ESC inputs retain their ordinary function. Its patch documentation requires a full flash to add or remove the patch and a calibration flash for later parameter edits; use the installed product's own instructions.

Selection, startup and shared axes in the Main Patch

The Main Patch guide distinguishes opening the selection display from committing the selected slot. With its documented default cruise-button assignment, holding the assigned button opens selection, up/down step through the slots, and SET commits immediately; otherwise the configured selection window commits the displayed slot after inactivity. A zero hold-time or window setting uses the vendor's stated defaults rather than an instantaneous action. Verify the installed assignment and patch version before interpreting the tachometer display.

Map at engine start can restore the last active slot or select a configured slot. Map follows drive mode, when enabled, maps each supported profile to a slot or to “No change”; in Eco the documented patch selects the slot's ECO torque limit. A remembered slot, a drive-mode selection and a button press are distinct inputs. The optional Start/Stop lamp takeover changes its indication while selection is open; the guide says button presses still reach the original Start/Stop function. Its ESC double-tap selection also performs the vehicle's ordinary ESC-button action, so the resulting traction state needs to be checked.

The documented Boost limit by rpm and gear is absolute hPa. Row 0 denotes neutral and row 1 first gear; higher gears use the last specified row, and the previous gear is held during a shift. Its ceiling does not establish measured manifold pressure or cancel other protections. Boost-limit rpm and spark-offset rpm/load axes are shared across slots. The guide also notes that selecting a lower per-slot rev threshold while engine speed is already above it can immediately invoke the limiter. These are properties of this implementation, not universal Simos 18 rules.

The vendor describes a VIN-fingerprint check: on mismatch, its boost limit, spark offset, flex-fuel, pops, RAL and launch features revert to their stock behaviour. That statement applies to the features listed by this patch's guide and does not prove that every calibration, fault response or other patch is unchanged. Confirm ECU identity and the installed software when a selected feature does not behave as expected.

Other mode systems and fuel

EcuTek RaceROM for EA888 documents four switch modes and its own per-mode torque, boost, ignition and lambda features. Its Boost Target Max Map Switch modes 1–4 are pressure-target ceilings; separate per-gear, per-mode torque-demand and reference-air-charge limits are also described. A ceiling is not a command to attain that pressure or torque. The guide documents per-mode full-load lambda targets and RaceROM part-load GDI/MPI lambda maps that replace corresponding OEM maps when the feature is used.

For ignition, the same guide describes mode-specific lift and no-lift RaceROM base maps, while OEM idle and flap-closed maps remain relevant in its described implementation. Final ignition is still subject to knock and other corrections. Check the installed feature and active path; changing a table that is bypassed in a given mode will not necessarily change the output. Its three-button stalk procedure cannot switch while rolling; the steering-wheel and multi-axis-stalk procedures use different inputs. These behaviours are product-specific and must not be assumed for another patch.

Manual fuel-map selection and sensor-based flex fuel are different. Confirm the fuel, active slot and actual ethanol source and blending configuration; selecting an ethanol-labelled slot does not measure fuel content.

Related: switchable maps · pops and bangs · crackle tuning · DSG shift sounds.

Launch and rolling anti-lag switches are implementation-specific. For the Main Patch and other examples, see the separate launch-control and rolling anti-lag guides, including their different gating and timeout behaviours.

Separate guides: traction control tuning · flat-foot shifting.

For the separate OEM and patch paths, see rev limiter tuning and vehicle-speed limiter tuning.

Source notes

Patch definition and supplier documentation reviewed 17 November 2026. Do not assume a listed label is present in every S50 revision or use generic XDF axis labels as proof of the underlying variables.

Revision 6: Simos 18 switchable maps

What is being switched?

Scope: These are documented or community-definition examples, not a universal map list for every Simos 18. Check the exact ECU, ASW, CAL, gearbox, patch and definition revision. Names, available functions, axis scaling, selectors and addresses vary. A calibration value or logger signal is not automatically a safe setting. None of the examples is a ready-made tune.

Some multi-map patches replicate selected maps or add per-slot modifiers in one ECU image. A selection changes the configured parameters; it is not necessarily a complete original-versus-tuned flash. A drive-mode button by itself does not establish that such a patch is present. The THANAS MQB description explicitly describes replicated calibration tables.

Switchleg S50 Switch Patch 29.33 V2: definition names

The pinned Switchleg1 S50 Switch Patch 29.33 V2 XDF is a patch-specific TunerPro definition titled SC8S50. Verify the exact ASW and matching patch before using it. Its five slot groups include the labels below. These are XDF display names supplied with that patch, not universal OEM Simos function identifiers. A title in an XDF does not alone prove the implementation or axes.

  • Torque Request AT Type 1/2/3; Torque Request MT Type 1/2: per-slot torque request groups as named in this XDF. Check gearbox selection and the actual request and limiting chain.
  • PUT setpoint: a per-slot pressure-related map labelled in hPa. The published XDF has generic axis descriptors, so confirm the patch's inputs and meaning rather than assuming it is a boost cap.
  • Spark modifier; Lambda modifier: per-slot modifiers. Confirm how and when each is applied in the corresponding patch documentation and log the result.
  • RPM limiter; Speed limiter; Pops enable: per-slot labels for limiter and sound selection.
  • Manual AFU: a manual ethanol-related value; the XDF description says changing this value does not by itself activate manual AFU.
  • Enable flex fuel spark/PUT/lambda/TQ/IAT/MPI modifier; Enable RAL; Enable NLS; Enable LC: feature-enable labels. Their presence in a definition does not prove a feature is activated in a given file.

The same XDF names a UI button selector for cruise cancel, cruise resume, variable-speed setpoint or pedals. These are definition labels, not a promise that every vehicle supports each input. Confirm the patch, input configuration and active slot. Displayed labels and map addresses must not be transferred to other patch revisions.

simos.app Main Patch: a different implementation

The simos.app Main Patch documentation describes two to five selectable slots. Its own labels include Torque Limit AT, Torque Limit MT, Torque Limit ECO, Boost limit by rpm and gear, Spark offset, Rev limit, Pops & bangs, Pops duration and Pops intensity. The boost limit is the lower of the OEM setpoint and the slot ceiling; it does not raise the OEM setpoint. The slot rev limit can lower the OEM limit. These are product-specific semantics, not the same thing as Switchleg's similarly named PUT setpoint.

The documented input options include configured cruise buttons, Start/Stop, ESC, a standstill indicator sequence and drive-mode association; availability and side effects depend on configuration. The vendor says its Start/Stop and ESC inputs retain their ordinary function. Its patch documentation requires a full flash to add or remove the patch and a calibration flash for later parameter edits; use the installed product's own instructions.

Selection, startup and shared axes in the Main Patch

The Main Patch guide distinguishes opening the selection display from committing the selected slot. With its documented default cruise-button assignment, holding the assigned button opens selection, up/down step through the slots, and SET commits immediately; otherwise the configured selection window commits the displayed slot after inactivity. A zero hold-time or window setting uses the vendor's stated defaults rather than an instantaneous action. Verify the installed assignment and patch version before interpreting the tachometer display.

Map at engine start can restore the last active slot or select a configured slot. Map follows drive mode, when enabled, maps each supported profile to a slot or to “No change”; in Eco the documented patch selects the slot's ECO torque limit. A remembered slot, a drive-mode selection and a button press are distinct inputs. The optional Start/Stop lamp takeover changes its indication while selection is open; the guide says button presses still reach the original Start/Stop function. Its ESC double-tap selection also performs the vehicle's ordinary ESC-button action, so the resulting traction state needs to be checked.

The documented Boost limit by rpm and gear is absolute hPa. Row 0 denotes neutral and row 1 first gear; higher gears use the last specified row, and the previous gear is held during a shift. Its ceiling does not establish measured manifold pressure or cancel other protections. Boost-limit rpm and spark-offset rpm/load axes are shared across slots. The guide also notes that selecting a lower per-slot rev threshold while engine speed is already above it can immediately invoke the limiter. These are properties of this implementation, not universal Simos 18 rules.

The vendor describes a VIN-fingerprint check: on mismatch, its boost limit, spark offset, flex-fuel, pops, RAL and launch features revert to their stock behaviour. That statement applies to the features listed by this patch's guide and does not prove that every calibration, fault response or other patch is unchanged. Confirm ECU identity and the installed software when a selected feature does not behave as expected.

Other mode systems and fuel

EcuTek RaceROM for EA888 documents four switch modes and its own per-mode torque, boost, ignition and lambda features. Its Boost Target Max Map Switch modes 1–4 are pressure-target ceilings; separate per-gear, per-mode torque-demand and reference-air-charge limits are also described. A ceiling is not a command to attain that pressure or torque. The guide documents per-mode full-load lambda targets and RaceROM part-load GDI/MPI lambda maps that replace corresponding OEM maps when the feature is used.

For ignition, the same guide describes mode-specific lift and no-lift RaceROM base maps, while OEM idle and flap-closed maps remain relevant in its described implementation. Final ignition is still subject to knock and other corrections. Check the installed feature and active path; changing a table that is bypassed in a given mode will not necessarily change the output. Its three-button stalk procedure cannot switch while rolling; the steering-wheel and multi-axis-stalk procedures use different inputs. These behaviours are product-specific and must not be assumed for another patch.

Manual fuel-map selection and sensor-based flex fuel are different. Confirm the fuel, active slot and actual ethanol source and blending configuration; selecting an ethanol-labelled slot does not measure fuel content.

Related: switchable maps · pops and bangs · crackle tuning · DSG shift sounds.

Launch and rolling anti-lag switches are implementation-specific. For the Main Patch and other examples, see the separate launch-control and rolling anti-lag guides, including their different gating and timeout behaviours.

Separate guides: traction control tuning · flat-foot shifting.

For the separate OEM and patch paths, see rev limiter tuning and vehicle-speed limiter tuning.

Source notes

Patch definition and supplier documentation reviewed 17 November 2026. Do not assume a listed label is present in every S50 revision or use generic XDF axis labels as proof of the underlying variables.