Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

Engine-speed limiting and scope

Simos 18 can coordinate more than one engine-speed threshold. The examples below come mainly from the community SC8S5031_C_OEM Simos 18.1 ENSL cross-reference, a specific reference image rather than a universal Simos 18 definition. Confirm ECU variant, ASW, CAL, gearbox, gear encoding, axis units, scaling, selectors and any patch against the actual file and logs. A listed map or representable value is not a recommended engine speed.

The reference describes a basic limit that can be fixed or calculated from gear, time and temperatures, followed by coordination with other limits. Engine-speed limiting, vehicle-speed limiting, standing launch and flat-foot shift are distinct functions, even where they interact.

Factory-related threshold maps and conditions

  • id_n_max_stat and id_n_max_dyn: static and dynamic engine-speed-limit curves in rpm, indexed by current gear on ldpm_gear_n_max. The reference describes a dynamic strategy permitting a higher limit for a calibrated time before a lower limit; verify which strategy and conditions apply on the target.
  • id_n_max_stat_vvl_h, id_n_max_stat_vvl_l, id_n_max_dyn_vvl_h and id_n_max_dyn_vvl_l: corresponding gear-indexed high/low variable-valve-lift variants. id_n_max_stat_sel_psn_h, id_n_max_dyn_sel_psn_h and the high-VVL selected-position variants concern selected gear position. Do not assume all branches are used in a given vehicle.
  • id_t_n_max_dyn_act: gear-indexed time associated with dynamic-limit activation; c_n_max_lgrd: rate limit for a decreasing engine-speed threshold. They shape time and transition behaviour, not the basic target alone.
  • ip_n_max_tco and ip_n_max_toil: engine-speed limits indexed by coolant temperature tco and oil temperature toil, respectively. c_n_max_mt is a stopped-manual-vehicle threshold; automatic/DCT variants have separate conditions. ip_n_max_gb_prot concerns gearbox communication-failure protection, not a normal road-speed map. Preserve and investigate protective and fault paths.

For the exact field descriptions and dimensions see ENSL limit coordination. The source also contains limits for fault and component conditions, and transmission-related coordination; a changed gear curve need not be the currently active threshold.

Controller and fuel-cut offsets

The ENSL application reference describes c_n_max_fcut_ofs as an rpm offset above n_max_thd for all-cylinder fuel cut in the described condition; c_n_max_fcut_ofs_lc and c_n_max_fcut_ofs_vst are separate launch and stopped-vehicle offsets. These offsets are not stand-alone base rev limits.

ip_fac_n_max_p_at, ip_fac_n_max_i_at, ip_fac_n_max_p_mt and ip_fac_n_max_i_mt, plus corresponding _fast_ variants, are controller factors with gear and predicted cylinder-air-mass inputs in the reference definition. They affect control behaviour rather than setting the nominal limiter rpm. See ENSL controller: prediction and torque control can precede different cut phases. The actual mode and response depend on configuration; do not infer a universal cut strategy from a label.

Fault and component protection examples

In the SC8S5031 injector-driver protection reference, ip_n_max_dr_prot is a speed-related curve against battery voltage, and its documented calculation also uses the maximum requested continuous injection-pulse count. It concerns low-voltage protection of the injection-driver DC/DC converter, not the ordinary gear-based engine limit. A weak battery, voltage drop or injection-system fault needs diagnosis rather than a higher base rev limit.

The ENSL reference labels id_n_max_sub a substitute engine-speed limit for a vehicle-speed error, indexed by transmission type; its copied functional-description text conflicts with the field label. ip_n_max_gb_prot is described for gearbox communication failure, but its km/h-labelled lookup axis is marked NO_INPUT_QUANTITY; verify the active source in the target software. lv_n_max_dyn_act indicates that the higher dynamic threshold could be applied. These fault and state fields are not evidence that an active limit is safe to raise.

The limiter controller reference identifies n_dif_max_lim as an engine-speed difference used by the controller, and tq_n_max_dif_p / tq_n_max_dif_i as proportional and integral torque contributions. The reference says those contributions are zero when its soft mode is inactive; zero in a single log sample is therefore not proof of a failed controller. lf_n_max_lim is a bit field described as detecting which engine-speed limits are set; decode it only with the matching software definition. ENSL adaptation reference.

Thermal shift requests and stationary protection

The SC8S5031 ENSL reference lists ip_fac_n_max_tcu_tco as a factor for a temperature-related gearshift request against coolant temperature tco and vehicle speed vs. ip_fac_n_max_tcu_tfu and ip_fac_n_max_tcu_toil are separate fuel- and oil-temperature-related factors against their respective temperature and engine speed n_32. These factors are not rev limits in rpm, and fuel or oil temperature may be modelled depending on the vehicle. Confirm the active branch and input source before interpreting a log.

ip_n_max_tcu_temp is labelled an engine-speed limitation by gearshift at high temperature, with rpm output and vehicle-speed input; its factor axis is marked NO_INPUT_QUANTITY in the extraction. Resolve the actual lookup and TCU communication on the matched software. A requested shift, the TCU's actual decision and a fuel-cut threshold are different events. Preserve thermal protection and investigate the cooling or measurement fault rather than masking an unexpected early shift.

The separate ENSL application reference describes a configured idle demand to protect the exhaust during prolonged high speed while stationary. It identifies c_n_max_set_is, c_pv_av_set_is and c_vs_n_max_set_is as engine-speed, raw-pedal and vehicle-speed conditions, and c_t_n_max_set_is as the time threshold in seconds. It describes timer start under the combined conditions and an idle request after the time expires with its specified conditions. This is a protective strategy, not a universal launch timeout; applicability and patch interaction need validation.

Patch and editor examples

The simos.app Main Patch documents per-slot Rev limit: it lowers the OEM threshold while that slot is active and cannot raise the OEM limit. In that documented implementation zero retains the OEM limit, values under 2,000 rpm are ignored, and selecting a lower limit while above it causes immediate intervention. These semantics are specific to this patch.

The pinned Switchleg S50 Switch Patch 29.33 V2 XDF has per-slot RPM limiter labels in rpm. They are patch-definition display names, not OEM identifiers; the XDF name alone does not establish zero behaviour, precedence or compatibility. The EcuTek EA888 engine guide uses editor descriptions including Engine Speed Maximum and stopped-vehicle and VVL-related limits; those descriptions are not necessarily OEM A2L symbols.

Verify the active limit

Where available, compare engine speed and gear with n_max_bas (basic calculated limit), n_max_raw (dynamic limit before change limitation), n_max_thd (coordinated threshold), n_pred_max_lim (predicted speed), lv_n_max_slow, lv_n_max_scc and lv_n_max_req_fcut. These are runtime values or states, not maps. Also record coolant and oil temperature, clutch state, active slot, torque request, throttle and fuel-cut status. Logger availability and state encoding depend on the definition. Sources: coordination and controller.

A DSG may shift before the ECU's selected threshold. EcuTek's DQ250 example ROM separately names maximum engine speed and forced-upshift settings; these are TCU-specific, not proof of the current ECU cut point. Assess the mechanical, valvetrain, lubrication and turbo capability of the actual engine and transmission before changing limits; downshift-induced overspeed may occur independently of an ECU torque cut.

Related: vehicle-speed limiter · launch control · flat-foot shifting · DSG torque coordination · switchable maps. References reviewed 17 November 2026.