Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

Scope and control paths

Traction control may involve the factory ABS/ESC system requesting a reduction in engine torque and applying brakes, an aftermarket ECU slip controller, or both. These functions are not interchangeable. The examples below concern specific Simos 18 / EA888 calibrations and custom code; verify the exact ECU, ASW, CAL, drivetrain, patch and definition. A map name alone does not establish that its feature is installed or active.

Factory ASR torque request: SC8S5031 example

The community SC8S5031 VHST cross-reference describes how the engine ECU handles fast and slow ASR torque requests. The following are research leads in that reference image, not a universal list or wheel-slip targets. Confirm the exact A2L, units, axes and system configuration before interpreting a file.

  • ip_fac_tqi_asr_slow_it: factor for the internally calculated slow ASR torque path. Its published axes are t_asr_act (ASR-active time, seconds; axis ldp_t_asr_act) and n_32 (engine rpm; axis ldp_n_32_asr_slow).
  • ip_lgrd_tqi_asr_bol: engine-speed-indexed change limitation associated with the lower ASR torque-request bound, intended to avoid a torque jump. c_tq_ofs_asr_slow is a slow-path torque offset in Nm for the stated single-channel case.
  • c_fac_tq_min_clu_asr_bol and c_n_sp_is_ratio_max_asr_lim concern the lower request limit and stall avoidance. c_t_dly_diag_asr and c_lgrd_tqi_inc_diag_asr concern the emergency ramp. Preserve and understand these protective functions.

Useful measurements in that reference include lv_asr_ena (intervention enabled), t_asr_act, tqi_asr_fast, tqi_asr_slow, tqi_asr_slow_it and tqi_asr_bol (lower bound). They are runtime signals, not calibration maps or direct measurements of delivered torque. The ASR path can coordinate with other torque requests and limits.

COBB custom traction control: table names

COBB's Volkswagen traction guide documents custom features for US-market Mk7 GTI and Golf R; its labels are Accesstuner names, not verified OEM A2L identifiers. Support and operation depend on the actual installed custom-feature and ROM version. Its controller compares calculated wheel slip with a target and uses proportional and integral terms to determine a spark-based correction.

  • Target Slip is indexed by vehicle speed and accelerator pedal position. Slip Target Multiplier, Slip Target Multiplier (Mode Selector), Mode 9 Slip Target Multiplier and Default User Traction Slot select or modify that target. The guide describes modes 1–8 using ROM-based per-gear gains and multiplier lookups, and mode 9 using its real-time values.
  • Per-Gear Proportional Component, Per-Gear Integral Component, (Mode 9) Proportional Component, (Mode 9) Integral Component, iState Minimum and iState Maximum set the documented P/I response and limits. Torque Reduction from Spark converts Trac Torque Reduction Percent into ignition reduction; its scale and the gains interact.
  • Minimum Vehicle Speed for Trac System Active references undriven-wheel speed. Slip Calculation Offset corrects a measurement offset and Steering Wheel Angle Slip Modification compensates calculated slip for steering angle.
  • Activate Traction Stagger Calcs, Front Tire Circumference and Rear Tire Circumference provide paired-axle tyre compensation for the GTI example. COBB says this affects its custom calculations, not the factory ABS/ESC wheel-speed measurements. Traction Control Enable enables this custom intervention; the guide says its slip calculations can still be monitored when the controller is disabled.

Gear changes and interpreting logs

In COBB's documented implementation, Trac Shift Occurring freezes traction calculations at their previous value during a shift. A manual car uses a clutch-switch input and Manual Gear Change Delay; a DSG uses current versus predicted gear and Gear Change Recognition Delay. Excessive manual freeze time can carry an existing reduction into the next gear. These timings and shift detection are specific to this system, not generic FFS or DSG settings. COBB shift description.

Compare wheel speeds, pedal, steering angle, gear, clutch or shift status, Factory TC Active, Trac Slip Percent, Trac Slip Percent Filtered, Trac Slip Target, Trac Torque Red. Proportional Comp., Trac Torque Red. Integral Comp., Trac Torque Reduction Percent and Trac Spark Reduction, where the matching logger exposes them. A slip calculation, target, torque-reduction request and delivered response are distinct. COBB monitor definitions.

Other patch approaches

The simos.app Main Patch calls its per-slot setting OEM ASR Sport mode. The publisher says it ignores ESP engine-torque-cut requests while retaining MSR and ESP brake/stability interventions; confirm actual behaviour for the vehicle and patch version. It is not an adjustable closed-loop slip target. The EcuTek EA888 RaceROM guide describes configurable custom maps using wheel-speed or slip inputs and available outputs; their map assignments depend on the tune, not fixed factory names.

Before evaluating a calibration, confirm tyre sizes, wheel-speed validity, braking/ESC state, active map and software versions; compare requested and actual response in a controlled setting. There is no universal target slip, gain or cut amount suitable for all tyres, surfaces and vehicles.

Related: flat-foot shifting · torque model · DSG torque coordination · switchable maps. References reviewed 17 November 2026.

For driven-wheel slip during overrun and MSR request/monitoring fields, see Simos 18 engine drag torque and MSR control.