Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Simos 18
Applies to
Simos 18.1
Tool groups
None
Manufacturers
Volkswagen Group

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

Pressure sensing, control and diagnosis

A high-pressure rail fault can arise from supply, the high-pressure pump, injectors, regulator, wiring, the pressure sensor, calibration or a combination. A single pressure reading or P0087 code does not identify the failed component. First establish the engine, ECU ASW/CAL, fuel-system layout and sensor fitment, then record freeze-frame data and compare the final high-pressure request and actual signal at the same time and in matching units.

Engineering identifiers below are examples from community SC8S5031_C_OEM FUSL fuel-pressure and system-pressure diagnostic extractions. They are research leads for a Simos 18.1 software example, not verified settings for all 18.x files. Confirm hardware, exact ASW/CAL, function selection, units and signal origin against the matched definition. Copied descriptions sometimes conflict; map ranges do not represent component ratings or proposed settings.

High-pressure sensor conversion and validity

c_fup_mes_slop is labelled the slope of the high-pressure fuel-sensor linear characteristic in hPa/V, while c_vp_fup_mes_ofs is a voltage-offset characteristic in V. The former's copied table caption instead describes a measured-pressure maximum; verify the active conversion and matched A2L before interpreting it. Neither is a desired rail-pressure map. FUSL fuel-pressure acquisition. c_fup_mes_crlc is a measured-pressure filter constant, and c_fup_mes_max is labelled a measurement limit. fup_mes is the measured-pressure runtime value in hPa in that reference. A displayed value can be conditioned or limited: clipping or a slow trace alone does not prove the actual pressure sensor or pump has reached a physical limit. c_vp_fup_mes_min_diag and c_vp_fup_mes_max_diag are sensor-voltage diagnostic thresholds in V. The extraction associates low voltage with ground-short/open-wire symptoms and high voltage with short-to-supply symptoms. lv_vp_fup_mes_not_vld is an out-of-range runtime flag. Electrical validity is not proof of accurate pressure over the sensor's full range. fup_sae is labelled SAE PID 59h absolute rail pressure in kPa; the source lists fup_mes in hPa. 1 bar = 100 kPa = 1,000 hPa, but confirm the logger's pressure reference and engineering conversion before comparing signals. ECU fallback, sampling and filtering may produce differences beyond a unit conversion. FUSL acquisition reference.

The separate sensor-diagnosis reference lists lv_cdn_diag_FUP_H and lv_cdn_diag_FUP_L as diagnostic condition flags and lv_err_FUP_H and lv_err_FUP_L as present failure information. In these names H/L refer to diagnostic branches; do not assume they indicate two separate physical fuel-pressure sensors. A monitor that is not enabled or has not completed cannot establish that a sensor has passed.

Sensor offsets and substitute values

In the FUSL adaptation reference, id_fup_min_ad is an adaptive fuel-pressure-minimum curve indexed by start coolant temperature tco_st in °C, with hPa output. fup_ad_ofs is a runtime pressure adaptation offset and lv_fup_ad_ena / lv_fup_ad_inh concern its conditions. These are not generic injector-flow corrections. Record diagnostic conditions and the matched software before interpreting an adapted value; resetting it does not repair a biased sensor or wiring fault.

The same function describes a substitute fuel-pressure value when the sensor has an error. lv_fup_lih_req in the limp-home reference is an HPFP limp-home request, while lv_fup_efp_mes_lih_req requests a low-pressure default value on its error path. Exact source selection and logger support depend on the application: do not assume a plausible displayed number is a live transducer measurement during a fault.

Pressure-system diagnosis and start-stop checks

fup_diag_mmv is a filtered or selected pressure value for diagnosis; c_crlc_fup_diag_mmv is its filter constant. fup_sp_grd_lim_diag is a gradient-limited diagnostic setpoint, not necessarily the instantaneous final control setpoint. lv_fup_sp_grd_lim_diag identifies a related general activation condition. These distinguish diagnosis from the underlying pressure controller and help explain why a brief transient mismatch is not automatically an active fault. FUSL pressure-system reference.

c_fup_dif_diag_min and c_fup_dif_diag_max are labelled minimum and maximum pressure-deviation thresholds in hPa; their copied descriptions are inconsistent, so verify the sign and actual comparison in the matched implementation. lv_cdn_diag_fup_sys_cmn represents common high-pressure diagnostic conditions, while lv_cdn_diag_fup_sys_cp concerns purge-related conditions. lv_sym_fup_mfp_plaus_0 and lv_sym_fup_mfp_plaus_1 are high/low pressure plausibility symptom flags, not a direct measurement proving the sensor itself is defective. Preserve fault monitoring and resolve the cause rather than widening thresholds to mask the problem.

The example stop-start monitor uses id_fup_stst_min_diag, a minimum pressure curve in hPa, and id_t_fup_stst, the active diagnostic time in seconds; both reference tfu_hpp in °C. lv_ena_diag_fup_stst and lv_rec_diag_fup_stst distinguish monitor enablement from conditions for recording. The source describes checking during a specific stop-start state; it is not a universal key-off leak-down test or an instruction to copy thresholds. The temperature may be modelled, depending on the vehicle and configuration. FUSL stop-start diagnosis; fuel-temperature guide.

Workshop and logging interpretation

Volkswagen's US technical tip 20-18-05TT covers certain 2014–2018 1.8/2.0 TSI engine codes and notes that a low-pressure channel on vehicles without a low-side sensor can display a fixed, invalid value. Its service process calls for vehicle-specific mechanical pressure checks. This is an example of why an attractive logger label is not proof of sensor fitment; it is not a claim that all Simos 18 cars lack the sensor or that the bulletin applies to every GTI.

For an engine with a genuine high-load pressure shortfall, compare requested and actual high-side pressure, confirmed low-side supply where physically fitted, pump command and voltage, temperature, injection state, lambda target and measured lambda, and fault/inhibition status across comparable conditions. A VW high-pressure pump bulletin illustrates checking low-side supply and conducting a guided pump test before replacement, but specifically covers earlier 2008–2015 CCTA/CBFA applications; its numerical targets and test procedure must not be transplanted to Simos 18 EA888 Gen3 cars. Follow the current service information for the actual engine and components. Use the specified safe depressurisation and test equipment for direct-injection fuel systems.

Related: direct injection and fuel pressure · HPFP control and upgrades · LPFP control and upgrades · fuel temperature · fuel trim. References reviewed 17 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Simos 18 fuel pressure sensor and diagnostic monitoring

Pressure sensing, control and diagnosis

A high-pressure rail fault can arise from supply, the high-pressure pump, injectors, regulator, wiring, the pressure sensor, calibration or a combination. A single pressure reading or P0087 code does not identify the failed component. First establish the engine, ECU ASW/CAL, fuel-system layout and sensor fitment, then record freeze-frame data and compare the final high-pressure request and actual signal at the same time and in matching units.

Engineering identifiers below are examples from community SC8S5031_C_OEM FUSL fuel-pressure and system-pressure diagnostic extractions. They are research leads for a Simos 18.1 software example, not verified settings for all 18.x files. Confirm hardware, exact ASW/CAL, function selection, units and signal origin against the matched definition. Copied descriptions sometimes conflict; map ranges do not represent component ratings or proposed settings.

High-pressure sensor conversion and validity

  • c_fup_mes_slop is labelled the slope of the high-pressure fuel-sensor linear characteristic in hPa/V, while c_vp_fup_mes_ofs is a voltage-offset characteristic in V. The former's copied table caption instead describes a measured-pressure maximum; verify the active conversion and matched A2L before interpreting it. Neither is a desired rail-pressure map. FUSL fuel-pressure acquisition.
  • c_fup_mes_crlc is a measured-pressure filter constant, and c_fup_mes_max is labelled a measurement limit. fup_mes is the measured-pressure runtime value in hPa in that reference. A displayed value can be conditioned or limited: clipping or a slow trace alone does not prove the actual pressure sensor or pump has reached a physical limit.
  • c_vp_fup_mes_min_diag and c_vp_fup_mes_max_diag are sensor-voltage diagnostic thresholds in V. The extraction associates low voltage with ground-short/open-wire symptoms and high voltage with short-to-supply symptoms. lv_vp_fup_mes_not_vld is an out-of-range runtime flag. Electrical validity is not proof of accurate pressure over the sensor's full range.
  • fup_sae is labelled SAE PID 59h absolute rail pressure in kPa; the source lists fup_mes in hPa. 1 bar = 100 kPa = 1,000 hPa, but confirm the logger's pressure reference and engineering conversion before comparing signals. ECU fallback, sampling and filtering may produce differences beyond a unit conversion. FUSL acquisition reference.

The separate sensor-diagnosis reference lists lv_cdn_diag_FUP_H and lv_cdn_diag_FUP_L as diagnostic condition flags and lv_err_FUP_H and lv_err_FUP_L as present failure information. In these names H/L refer to diagnostic branches; do not assume they indicate two separate physical fuel-pressure sensors. A monitor that is not enabled or has not completed cannot establish that a sensor has passed.

Sensor offsets and substitute values

In the FUSL adaptation reference, id_fup_min_ad is an adaptive fuel-pressure-minimum curve indexed by start coolant temperature tco_st in °C, with hPa output. fup_ad_ofs is a runtime pressure adaptation offset and lv_fup_ad_ena / lv_fup_ad_inh concern its conditions. These are not generic injector-flow corrections. Record diagnostic conditions and the matched software before interpreting an adapted value; resetting it does not repair a biased sensor or wiring fault.

The same function describes a substitute fuel-pressure value when the sensor has an error. lv_fup_lih_req in the limp-home reference is an HPFP limp-home request, while lv_fup_efp_mes_lih_req requests a low-pressure default value on its error path. Exact source selection and logger support depend on the application: do not assume a plausible displayed number is a live transducer measurement during a fault.

Pressure-system diagnosis and start-stop checks

fup_diag_mmv is a filtered or selected pressure value for diagnosis; c_crlc_fup_diag_mmv is its filter constant. fup_sp_grd_lim_diag is a gradient-limited diagnostic setpoint, not necessarily the instantaneous final control setpoint. lv_fup_sp_grd_lim_diag identifies a related general activation condition. These distinguish diagnosis from the underlying pressure controller and help explain why a brief transient mismatch is not automatically an active fault. FUSL pressure-system reference.

c_fup_dif_diag_min and c_fup_dif_diag_max are labelled minimum and maximum pressure-deviation thresholds in hPa; their copied descriptions are inconsistent, so verify the sign and actual comparison in the matched implementation. lv_cdn_diag_fup_sys_cmn represents common high-pressure diagnostic conditions, while lv_cdn_diag_fup_sys_cp concerns purge-related conditions. lv_sym_fup_mfp_plaus_0 and lv_sym_fup_mfp_plaus_1 are high/low pressure plausibility symptom flags, not a direct measurement proving the sensor itself is defective. Preserve fault monitoring and resolve the cause rather than widening thresholds to mask the problem.

The example stop-start monitor uses id_fup_stst_min_diag, a minimum pressure curve in hPa, and id_t_fup_stst, the active diagnostic time in seconds; both reference tfu_hpp in °C. lv_ena_diag_fup_stst and lv_rec_diag_fup_stst distinguish monitor enablement from conditions for recording. The source describes checking during a specific stop-start state; it is not a universal key-off leak-down test or an instruction to copy thresholds. The temperature may be modelled, depending on the vehicle and configuration. FUSL stop-start diagnosis; fuel-temperature guide.

Workshop and logging interpretation

Volkswagen's US technical tip 20-18-05TT covers certain 2014–2018 1.8/2.0 TSI engine codes and notes that a low-pressure channel on vehicles without a low-side sensor can display a fixed, invalid value. Its service process calls for vehicle-specific mechanical pressure checks. This is an example of why an attractive logger label is not proof of sensor fitment; it is not a claim that all Simos 18 cars lack the sensor or that the bulletin applies to every GTI.

For an engine with a genuine high-load pressure shortfall, compare requested and actual high-side pressure, confirmed low-side supply where physically fitted, pump command and voltage, temperature, injection state, lambda target and measured lambda, and fault/inhibition status across comparable conditions. A VW high-pressure pump bulletin illustrates checking low-side supply and conducting a guided pump test before replacement, but specifically covers earlier 2008–2015 CCTA/CBFA applications; its numerical targets and test procedure must not be transplanted to Simos 18 EA888 Gen3 cars. Follow the current service information for the actual engine and components. Use the specified safe depressurisation and test equipment for direct-injection fuel systems.

Related: direct injection and fuel pressure · HPFP control and upgrades · LPFP control and upgrades · fuel temperature · fuel trim. References reviewed 17 November 2026.

Revision 1: Simos 18 fuel pressure sensor and diagnostic monitoring

Pressure sensing, control and diagnosis

A high-pressure rail fault can arise from supply, the high-pressure pump, injectors, regulator, wiring, the pressure sensor, calibration or a combination. A single pressure reading or P0087 code does not identify the failed component. First establish the engine, ECU ASW/CAL, fuel-system layout and sensor fitment, then record freeze-frame data and compare the final high-pressure request and actual signal at the same time and in matching units.

Engineering identifiers below are examples from community SC8S5031_C_OEM FUSL fuel-pressure and system-pressure diagnostic extractions. They are research leads for a Simos 18.1 software example, not verified settings for all 18.x files. Confirm hardware, exact ASW/CAL, function selection, units and signal origin against the matched definition. Copied descriptions sometimes conflict; map ranges do not represent component ratings or proposed settings.

High-pressure sensor conversion and validity

  • c_fup_mes_slop is labelled the slope of the high-pressure fuel-sensor linear characteristic in hPa/V, while c_vp_fup_mes_ofs is a voltage-offset characteristic in V. The former's copied table caption instead describes a measured-pressure maximum; verify the active conversion and matched A2L before interpreting it. Neither is a desired rail-pressure map. FUSL fuel-pressure acquisition.
  • c_fup_mes_crlc is a measured-pressure filter constant, and c_fup_mes_max is labelled a measurement limit. fup_mes is the measured-pressure runtime value in hPa in that reference. A displayed value can be conditioned or limited: clipping or a slow trace alone does not prove the actual pressure sensor or pump has reached a physical limit.
  • c_vp_fup_mes_min_diag and c_vp_fup_mes_max_diag are sensor-voltage diagnostic thresholds in V. The extraction associates low voltage with ground-short/open-wire symptoms and high voltage with short-to-supply symptoms. lv_vp_fup_mes_not_vld is an out-of-range runtime flag. Electrical validity is not proof of accurate pressure over the sensor's full range.
  • fup_sae is labelled SAE PID 59h absolute rail pressure in kPa; the source lists fup_mes in hPa. 1 bar = 100 kPa = 1,000 hPa, but confirm the logger's pressure reference and engineering conversion before comparing signals. ECU fallback, sampling and filtering may produce differences beyond a unit conversion. FUSL acquisition reference.

The separate sensor-diagnosis reference lists lv_cdn_diag_FUP_H and lv_cdn_diag_FUP_L as diagnostic condition flags and lv_err_FUP_H and lv_err_FUP_L as present failure information. In these names H/L refer to diagnostic branches; do not assume they indicate two separate physical fuel-pressure sensors. A monitor that is not enabled or has not completed cannot establish that a sensor has passed.

Sensor offsets and substitute values

In the FUSL adaptation reference, id_fup_min_ad is an adaptive fuel-pressure-minimum curve indexed by start coolant temperature tco_st in °C, with hPa output. fup_ad_ofs is a runtime pressure adaptation offset and lv_fup_ad_ena / lv_fup_ad_inh concern its conditions. These are not generic injector-flow corrections. Record diagnostic conditions and the matched software before interpreting an adapted value; resetting it does not repair a biased sensor or wiring fault.

The same function describes a substitute fuel-pressure value when the sensor has an error. lv_fup_lih_req in the limp-home reference is an HPFP limp-home request, while lv_fup_efp_mes_lih_req requests a low-pressure default value on its error path. Exact source selection and logger support depend on the application: do not assume a plausible displayed number is a live transducer measurement during a fault.

Pressure-system diagnosis and start-stop checks

fup_diag_mmv is a filtered or selected pressure value for diagnosis; c_crlc_fup_diag_mmv is its filter constant. fup_sp_grd_lim_diag is a gradient-limited diagnostic setpoint, not necessarily the instantaneous final control setpoint. lv_fup_sp_grd_lim_diag identifies a related general activation condition. These distinguish diagnosis from the underlying pressure controller and help explain why a brief transient mismatch is not automatically an active fault. FUSL pressure-system reference.

c_fup_dif_diag_min and c_fup_dif_diag_max are labelled minimum and maximum pressure-deviation thresholds in hPa; their copied descriptions are inconsistent, so verify the sign and actual comparison in the matched implementation. lv_cdn_diag_fup_sys_cmn represents common high-pressure diagnostic conditions, while lv_cdn_diag_fup_sys_cp concerns purge-related conditions. lv_sym_fup_mfp_plaus_0 and lv_sym_fup_mfp_plaus_1 are high/low pressure plausibility symptom flags, not a direct measurement proving the sensor itself is defective. Preserve fault monitoring and resolve the cause rather than widening thresholds to mask the problem.

The example stop-start monitor uses id_fup_stst_min_diag, a minimum pressure curve in hPa, and id_t_fup_stst, the active diagnostic time in seconds; both reference tfu_hpp in °C. lv_ena_diag_fup_stst and lv_rec_diag_fup_stst distinguish monitor enablement from conditions for recording. The source describes checking during a specific stop-start state; it is not a universal key-off leak-down test or an instruction to copy thresholds. The temperature may be modelled, depending on the vehicle and configuration. FUSL stop-start diagnosis; fuel-temperature guide.

Workshop and logging interpretation

Volkswagen's US technical tip 20-18-05TT covers certain 2014–2018 1.8/2.0 TSI engine codes and notes that a low-pressure channel on vehicles without a low-side sensor can display a fixed, invalid value. Its service process calls for vehicle-specific mechanical pressure checks. This is an example of why an attractive logger label is not proof of sensor fitment; it is not a claim that all Simos 18 cars lack the sensor or that the bulletin applies to every GTI.

For an engine with a genuine high-load pressure shortfall, compare requested and actual high-side pressure, confirmed low-side supply where physically fitted, pump command and voltage, temperature, injection state, lambda target and measured lambda, and fault/inhibition status across comparable conditions. A VW high-pressure pump bulletin illustrates checking low-side supply and conducting a guided pump test before replacement, but specifically covers earlier 2008–2015 CCTA/CBFA applications; its numerical targets and test procedure must not be transplanted to Simos 18 EA888 Gen3 cars. Follow the current service information for the actual engine and components. Use the specified safe depressurisation and test equipment for direct-injection fuel systems.

Related: direct injection and fuel pressure · HPFP control and upgrades · LPFP control and upgrades · fuel temperature · fuel trim. References reviewed 17 November 2026.