Scope: modelled versus measured fuel temperature
Fuel temperature is used in the injection and high-pressure pump models, but a temperature value in a logger is not necessarily a sensor reading. COBB's MQB monitor list explicitly describes its HPFP Fuel Temperature channel as modelled. The list covers its specified Mk7/Mk7.5 GTI and Golf R and A3/S3 applications; channel availability depends on software and logging tool.
The following map names are research examples from the community SC8S5031_C_OEM fuel-temperature cross-reference and related functions. They are not universal values or proof that a branch or sensor is fitted and active. Verify exact ECU application, ASW/CAL, definitions, axes, units, selectors and physical measurement location before drawing tuning conclusions.
Static temperature model and heat-soak corrections
ip_tfu_stat_coldandip_tfu_stat_hotare cold and hot static-state fuel-temperature maps. Their axes aremff_sp_fup_ctl, shown in mg by this extraction, andn_32in rpm; outputs are °C. The runtimefac_tfu_statweights interpolation between the maps in relation to ambient temperature. It is a runtime factor, not another calibration map. FUSL fuel-temperature reference.ip_tfu_t_es_corsupplies a temperature offset againstt_esin minutes.ip_fac_tfu_t_es_t_astdefines the fade of this offset againstt_astin seconds after start.ip_tfu_vs_corsupplies a temperature correction against vehicle speedvsin km/h. Confirm the exact selected input and initialization for the target calibration; a restart after a heat soak can follow a different model path from a cold start.tfu_mdl,tfu_mdl_2,tfu_hpp_1andtfu_efp_1are listed as runtime model-path values. Their labels relate to different stages or locations; do not treat each as a separate fitted sensor or interchange them without confirming their calculation and selection.
Injection and MPI temperature compensation
In the SC8S5031 INJR injection reference, ip_fac_mff_temp_cor supplies a fuel-injection correction factor against tfu_inj in °C: the documented relationship is fac_mff_tfu = ip_fac_mff_temp_cor(tfu_inj). Determine which source feeds tfu_inj in the target configuration before equating it to a measured rail or sensor temperature. This factor does not replace correct injector characterization, fuel pressure or ethanol-content calibration.
For a configured MPI path, ip_fac_tfu_mpi_stat weights an MPI temperature estimate between cylinder inlet air temperature tia_cyl and injector-inlet fuel-temperature value tfu_efp; ip_fac_crlc_tfu_mpi_dyn is the dynamic-filter coefficient. Both use mff_mpi_tfu in g/s in this reference. Confirm the MPI hardware, active branch and input source; these names do not establish that a physical MPI temperature sensor is fitted. INJR reference.
HPFP control and pressure-request limits
ip_fac_fuel_pump_eff_tfu_n is an efficiency-related model factor indexed by engine speed and HPFP fuel-temperature input in the FUSL actuator-control reference. It is part of the pump model; its label is not a direct pump flow measurement or a universal pump capacity. Establish whether the relevant input is measured or estimated in the specific car.
The FUSL setpoint extraction describes ip_fup_sp_max as a pressure-setpoint ceiling based on coolant temperature TCO, but its axis metadata identifies tfu (fuel temperature) in °C. Resolve that conflict against the matched function and definition before interpreting or changing it. Output is labelled hPa; 1 bar is 1,000 hPa. A setpoint ceiling is not a measurement of actual rail pressure, and pressure reference and scaling must match when comparing logs.
Flex-fuel sensor and diagnosis
EcuTek's EA888 flex-fuel documentation describes a compatible sensor signal that can supply both ethanol content and fuel temperature in its supported configuration. The sensor reports conditions at its installation point; that does not establish injector or pump temperature, nor that every OEM temperature model uses the signal. Verify the specific kit, configuration and software. Ethanol content, fuel temperature and fuel density are different quantities.
For a repeatable diagnosis, record engine and ECU identification, fuel blend, ambient and coolant temperatures, time since shutdown, running conditions, lambda target and actual, trims, high-pressure target and actual, and low-side pressure and pump command where fitted and supported. Compare cold, warm and heat-soaked starts under similar conditions. If temperature matters to a diagnosis, establish whether each channel is modelled or measured and, for a physical sensor, its location. Investigate pressure supply, leaks, injector data and sensors before attributing a temperature-related symptom to a particular map. Use the applicable workshop procedure for fuel-system testing.
Related: HPFP control and upgrades · injector characterisation · fuel system and MPI · ethanol and flex fuel · fuel trims. References reviewed 17 November 2026.