Removed text is struck through; added text is highlighted.
Why gear and clutch state matter
Gear-dependent torque or boost functions and aftermarket no-lift shifting depend on the state and source selected by that particular implementation. A displayed gear is not necessarily a direct selector measurement. For its supported MQB vehicles, COBB's monitor list calls Current Gear calculated and lists Clutch Switch separately; it labels Current Gear Predicted as DSG-only. Logger labels and availability depend on product, software, gearbox and vehicle.
The following community SC8S5031_C_OEM TRSM gear-detection and clutch-diagnosis cross-references are examples from a Simos 18.1 software definition. Confirm the actual ECU ASW/CAL, gearbox configuration, sensor fitment, source selection, units and available logger channels before use. A named function or switch does not establish that a particular manual vehicle has a physical gear-position sensor, two discrete clutch switches or the relevant branch enabled.
Manual gear recognition
id_gear_gr_mt is a manual-transmission gear-from-ratio characteristic in the TRSM extraction, with n_vs_h_res_cor as its axis in rpm/(km/h). It maps a corrected speed ratio to a gear classification; it is not a torque or boost target. Other entries including id_gear_gr_mt_4wd exist but require the corresponding configured drivetrain and software.
n_vs is a runtime engine-speed/vehicle-speed ratio; n_vs_fil_trsm is a filtered ratio and n_vs_h_res_cor is the corrected high-resolution value used as the characteristic's input. For illustration only, 3,000 rpm divided by 100 km/h is 30 rpm/(km/h). Ratio-based recognition depends on reliable speed inputs and a connected drivetrain; clutch disengagement, slip, wrong tyre/gear configuration, or low speed can make a ratio unsuitable. Confirm ECU speed source, unit conversion and valid detection conditions before using a log to diagnose a fault.
c_vs_fil_min_gear is labelled a minimum vehicle speed for gear detection in km/h; the extracted table narrative instead describes a converter-torque threshold. Resolve that metadata conflict against the matching implementation. c_t_max_gear_hld_mt is a manual held-gear time limit in seconds. Neither is a universal recommended value.
gear_hld is a runtime held-gear signal described as retaining the previous gear until a new one is detected at the end of a shift; lv_gs denotes a shift-active state. Held gear, raw gear and a physical lever position are different concepts. Actual use and enumerations must be established on the target. TRSM gear reference.
c_cir_veh_whl_gr_ref is labelled wheel-circumference reference for gear ratio in mm, and lc_cir_veh_whl_gr_ena is present in the same extraction. Establish the configured calculation before assuming a tyre-size change requires changing a calibration. Verify matching wheel/tyre sizes, vehicle-speed data, drivetrain and any sensor errors first; do not change these values simply to hide an incorrect gear display.
Clutch-input plausibility
The TRSM clutch-diagnosis reference contains c_thd_pv_clu_act and c_thd_pv_clu_not_act, clutch-pedal-value thresholds, in percent, where the diagnostic expects the relevant switch to indicate activated and not activated. c_t_clu_swi_2_not_plaus is an implausibility debounce time in seconds. lv_clu_swi_2_not_plaus is a runtime flag associated with the second, interlock switch in this reference. These are diagnostic terms, not a universal pedal setting or a substitute for repairing wiring and hardware.
c_t_min_gear_chg_det_err_cs describes the minimum time of a pending changed gear for the gear-change-based clutch-switch diagnostic, in seconds; lv_cs_err_gear_chg_det records that a change was detected for this calculation. lv_cdn_diag_CS_PV identifies diagnostic conditions fulfilled. A monitor that has not run cannot demonstrate a pass; a flag requires the corresponding enabled conditions and software-specific interpretation. Do not disable start interlocks, plausibility checks or fault monitoring to make a tuning feature appear to work.
Logging and product-specific features
Record the ECU/gearbox identification, tyre and final-drive configuration, fault codes and freeze-frame data. In a safe stationary test, compare the scan tool's actual clutch-switch indication with pedal operation using the vehicle's service procedure. Where a controlled road or dynamometer test is appropriate, log RPM, vehicle speed, calculated and held gear if available, clutch state, pedal and throttle position, torque/boost request and actual, feature-enable and intervention states. Check whether the logged value is raw, filtered, calculated, held or transmitted. An RPM rise with clutch released can have several causes; a speed ratio alone does not prove clutch slip.
For example, simos.app Main Patch documents a patch-specific boost-limit-by-gear table and says the last gear is held during a shift. This behaviour is specific to that patch and version and is not proof that every factory or other aftermarket gear table behaves the same way. COBB's US-market Mk7 GTI FFS description describes holding a shift RPM limit when the clutch is depressed. Check exact feature enablement and its monitored conditions before attributing a failed feature to the clutch input.
In a 2016 manual GTI owner discussion, an EQT/COBB user reported that launch and flat-foot shifting did not work despite pressing the clutch. The report does not independently identify the ECU software, the actual switch state or a confirmed fix; it illustrates why feature readiness, configuration and input signals all need checking rather than assuming a bad switch.
Related: flat-foot shifting · torque and boost by gear · launch control · traction control · DSG torque coordination. References reviewed 17 November 2026.
Open each version to inspect formatting, tables and photographs.
Revision 1: Simos 18 manual gear detection and clutch switch diagnosis
Why gear and clutch state matter
Gear-dependent torque or boost functions and aftermarket no-lift shifting depend on the state and source selected by that particular implementation. A displayed gear is not necessarily a direct selector measurement. For its supported MQB vehicles, COBB's monitor list calls Current Gear calculated and lists Clutch Switch separately; it labels Current Gear Predicted as DSG-only. Logger labels and availability depend on product, software, gearbox and vehicle.
The following community SC8S5031_C_OEM TRSM gear-detection and clutch-diagnosis cross-references are examples from a Simos 18.1 software definition. Confirm the actual ECU ASW/CAL, gearbox configuration, sensor fitment, source selection, units and available logger channels before use. A named function or switch does not establish that a particular manual vehicle has a physical gear-position sensor, two discrete clutch switches or the relevant branch enabled.
Manual gear recognition
id_gear_gr_mt is a manual-transmission gear-from-ratio characteristic in the TRSM extraction, with n_vs_h_res_cor as its axis in rpm/(km/h). It maps a corrected speed ratio to a gear classification; it is not a torque or boost target. Other entries including id_gear_gr_mt_4wd exist but require the corresponding configured drivetrain and software.
n_vs is a runtime engine-speed/vehicle-speed ratio; n_vs_fil_trsm is a filtered ratio and n_vs_h_res_cor is the corrected high-resolution value used as the characteristic's input. For illustration only, 3,000 rpm divided by 100 km/h is 30 rpm/(km/h). Ratio-based recognition depends on reliable speed inputs and a connected drivetrain; clutch disengagement, slip, wrong tyre/gear configuration, or low speed can make a ratio unsuitable. Confirm ECU speed source, unit conversion and valid detection conditions before using a log to diagnose a fault.
c_vs_fil_min_gear is labelled a minimum vehicle speed for gear detection in km/h; the extracted table narrative instead describes a converter-torque threshold. Resolve that metadata conflict against the matching implementation. c_t_max_gear_hld_mt is a manual held-gear time limit in seconds. Neither is a universal recommended value.
gear_hld is a runtime held-gear signal described as retaining the previous gear until a new one is detected at the end of a shift; lv_gs denotes a shift-active state. Held gear, raw gear and a physical lever position are different concepts. Actual use and enumerations must be established on the target. TRSM gear reference.
c_cir_veh_whl_gr_ref is labelled wheel-circumference reference for gear ratio in mm, and lc_cir_veh_whl_gr_ena is present in the same extraction. Establish the configured calculation before assuming a tyre-size change requires changing a calibration. Verify matching wheel/tyre sizes, vehicle-speed data, drivetrain and any sensor errors first; do not change these values simply to hide an incorrect gear display.
Clutch-input plausibility
The TRSM clutch-diagnosis reference contains c_thd_pv_clu_act and c_thd_pv_clu_not_act, clutch-pedal-value thresholds, in percent, where the diagnostic expects the relevant switch to indicate activated and not activated. c_t_clu_swi_2_not_plaus is an implausibility debounce time in seconds. lv_clu_swi_2_not_plaus is a runtime flag associated with the second, interlock switch in this reference. These are diagnostic terms, not a universal pedal setting or a substitute for repairing wiring and hardware.
c_t_min_gear_chg_det_err_cs describes the minimum time of a pending changed gear for the gear-change-based clutch-switch diagnostic, in seconds; lv_cs_err_gear_chg_det records that a change was detected for this calculation. lv_cdn_diag_CS_PV identifies diagnostic conditions fulfilled. A monitor that has not run cannot demonstrate a pass; a flag requires the corresponding enabled conditions and software-specific interpretation. Do not disable start interlocks, plausibility checks or fault monitoring to make a tuning feature appear to work.
Logging and product-specific features
Record the ECU/gearbox identification, tyre and final-drive configuration, fault codes and freeze-frame data. In a safe stationary test, compare the scan tool's actual clutch-switch indication with pedal operation using the vehicle's service procedure. Where a controlled road or dynamometer test is appropriate, log RPM, vehicle speed, calculated and held gear if available, clutch state, pedal and throttle position, torque/boost request and actual, feature-enable and intervention states. Check whether the logged value is raw, filtered, calculated, held or transmitted. An RPM rise with clutch released can have several causes; a speed ratio alone does not prove clutch slip.
For example, simos.app Main Patch documents a patch-specific boost-limit-by-gear table and says the last gear is held during a shift. This behaviour is specific to that patch and version and is not proof that every factory or other aftermarket gear table behaves the same way. COBB's US-market Mk7 GTI FFS description describes holding a shift RPM limit when the clutch is depressed. Check exact feature enablement and its monitored conditions before attributing a failed feature to the clutch input.
In a 2016 manual GTI owner discussion, an EQT/COBB user reported that launch and flat-foot shifting did not work despite pressing the clutch. The report does not independently identify the ECU software, the actual switch state or a confirmed fix; it illustrates why feature readiness, configuration and input signals all need checking rather than assuming a bad switch.
Related: flat-foot shifting · torque and boost by gear · launch control · traction control · DSG torque coordination. References reviewed 17 November 2026.
Revision 1: Simos 18 manual gear detection and clutch switch diagnosis
Why gear and clutch state matter
Gear-dependent torque or boost functions and aftermarket no-lift shifting depend on the state and source selected by that particular implementation. A displayed gear is not necessarily a direct selector measurement. For its supported MQB vehicles, COBB's monitor list calls Current Gear calculated and lists Clutch Switch separately; it labels Current Gear Predicted as DSG-only. Logger labels and availability depend on product, software, gearbox and vehicle.
The following community SC8S5031_C_OEM TRSM gear-detection and clutch-diagnosis cross-references are examples from a Simos 18.1 software definition. Confirm the actual ECU ASW/CAL, gearbox configuration, sensor fitment, source selection, units and available logger channels before use. A named function or switch does not establish that a particular manual vehicle has a physical gear-position sensor, two discrete clutch switches or the relevant branch enabled.
Manual gear recognition
id_gear_gr_mt is a manual-transmission gear-from-ratio characteristic in the TRSM extraction, with n_vs_h_res_cor as its axis in rpm/(km/h). It maps a corrected speed ratio to a gear classification; it is not a torque or boost target. Other entries including id_gear_gr_mt_4wd exist but require the corresponding configured drivetrain and software.
n_vs is a runtime engine-speed/vehicle-speed ratio; n_vs_fil_trsm is a filtered ratio and n_vs_h_res_cor is the corrected high-resolution value used as the characteristic's input. For illustration only, 3,000 rpm divided by 100 km/h is 30 rpm/(km/h). Ratio-based recognition depends on reliable speed inputs and a connected drivetrain; clutch disengagement, slip, wrong tyre/gear configuration, or low speed can make a ratio unsuitable. Confirm ECU speed source, unit conversion and valid detection conditions before using a log to diagnose a fault.
c_vs_fil_min_gear is labelled a minimum vehicle speed for gear detection in km/h; the extracted table narrative instead describes a converter-torque threshold. Resolve that metadata conflict against the matching implementation. c_t_max_gear_hld_mt is a manual held-gear time limit in seconds. Neither is a universal recommended value.
gear_hld is a runtime held-gear signal described as retaining the previous gear until a new one is detected at the end of a shift; lv_gs denotes a shift-active state. Held gear, raw gear and a physical lever position are different concepts. Actual use and enumerations must be established on the target. TRSM gear reference.
c_cir_veh_whl_gr_ref is labelled wheel-circumference reference for gear ratio in mm, and lc_cir_veh_whl_gr_ena is present in the same extraction. Establish the configured calculation before assuming a tyre-size change requires changing a calibration. Verify matching wheel/tyre sizes, vehicle-speed data, drivetrain and any sensor errors first; do not change these values simply to hide an incorrect gear display.
Clutch-input plausibility
The TRSM clutch-diagnosis reference contains c_thd_pv_clu_act and c_thd_pv_clu_not_act, clutch-pedal-value thresholds, in percent, where the diagnostic expects the relevant switch to indicate activated and not activated. c_t_clu_swi_2_not_plaus is an implausibility debounce time in seconds. lv_clu_swi_2_not_plaus is a runtime flag associated with the second, interlock switch in this reference. These are diagnostic terms, not a universal pedal setting or a substitute for repairing wiring and hardware.
c_t_min_gear_chg_det_err_cs describes the minimum time of a pending changed gear for the gear-change-based clutch-switch diagnostic, in seconds; lv_cs_err_gear_chg_det records that a change was detected for this calculation. lv_cdn_diag_CS_PV identifies diagnostic conditions fulfilled. A monitor that has not run cannot demonstrate a pass; a flag requires the corresponding enabled conditions and software-specific interpretation. Do not disable start interlocks, plausibility checks or fault monitoring to make a tuning feature appear to work.
Logging and product-specific features
Record the ECU/gearbox identification, tyre and final-drive configuration, fault codes and freeze-frame data. In a safe stationary test, compare the scan tool's actual clutch-switch indication with pedal operation using the vehicle's service procedure. Where a controlled road or dynamometer test is appropriate, log RPM, vehicle speed, calculated and held gear if available, clutch state, pedal and throttle position, torque/boost request and actual, feature-enable and intervention states. Check whether the logged value is raw, filtered, calculated, held or transmitted. An RPM rise with clutch released can have several causes; a speed ratio alone does not prove clutch slip.
For example, simos.app Main Patch documents a patch-specific boost-limit-by-gear table and says the last gear is held during a shift. This behaviour is specific to that patch and version and is not proof that every factory or other aftermarket gear table behaves the same way. COBB's US-market Mk7 GTI FFS description describes holding a shift RPM limit when the clutch is depressed. Check exact feature enablement and its monitored conditions before attributing a failed feature to the clutch input.
In a 2016 manual GTI owner discussion, an EQT/COBB user reported that launch and flat-foot shifting did not work despite pressing the clutch. The report does not independently identify the ECU software, the actual switch state or a confirmed fix; it illustrates why feature readiness, configuration and input signals all need checking rather than assuming a bad switch.
Related: flat-foot shifting · torque and boost by gear · launch control · traction control · DSG torque coordination. References reviewed 17 November 2026.