Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Simos 18
Applies to
Simos 18.1
Tool groups
None
Manufacturers
Volkswagen Group

Why gear and clutch state matter

Gear-dependent torque or boost functions and aftermarket no-lift shifting depend on the state and source selected by that particular implementation. A displayed gear is not necessarily a direct selector measurement. For its supported MQB vehicles, COBB's monitor list calls Current Gear calculated and lists Clutch Switch separately; it labels Current Gear Predicted as DSG-only. Logger labels and availability depend on product, software, gearbox and vehicle.

The following community SC8S5031_C_OEM TRSM gear-detection and clutch-diagnosis cross-references are examples from a Simos 18.1 software definition. Confirm the actual ECU ASW/CAL, gearbox configuration, sensor fitment, source selection, units and available logger channels before use. A named function or switch does not establish that a particular manual vehicle has a physical gear-position sensor, two discrete clutch switches or the relevant branch enabled.

Manual gear recognition

  • id_gear_gr_mt is a manual-transmission gear-from-ratio characteristic in the TRSM extraction, with n_vs_h_res_cor as its axis in rpm/(km/h). It maps a corrected speed ratio to a gear classification; it is not a torque or boost target. Other entries including id_gear_gr_mt_4wd exist but require the corresponding configured drivetrain and software.
  • n_vs is a runtime engine-speed/vehicle-speed ratio; n_vs_fil_trsm is a filtered ratio and n_vs_h_res_cor is the corrected high-resolution value used as the characteristic's input. For illustration only, 3,000 rpm divided by 100 km/h is 30 rpm/(km/h). Ratio-based recognition depends on reliable speed inputs and a connected drivetrain; clutch disengagement, slip, wrong tyre/gear configuration, or low speed can make a ratio unsuitable. Confirm ECU speed source, unit conversion and valid detection conditions before using a log to diagnose a fault.
  • c_vs_fil_min_gear is labelled a minimum vehicle speed for gear detection in km/h; the extracted table narrative instead describes a converter-torque threshold. Resolve that metadata conflict against the matching implementation. c_t_max_gear_hld_mt is a manual held-gear time limit in seconds. Neither is a universal recommended value.
  • gear_hld is a runtime held-gear signal described as retaining the previous gear until a new one is detected at the end of a shift; lv_gs denotes a shift-active state. Held gear, raw gear and a physical lever position are different concepts. Actual use and enumerations must be established on the target. TRSM gear reference.

c_cir_veh_whl_gr_ref is labelled wheel-circumference reference for gear ratio in mm, and lc_cir_veh_whl_gr_ena is present in the same extraction. Establish the configured calculation before assuming a tyre-size change requires changing a calibration. Verify matching wheel/tyre sizes, vehicle-speed data, drivetrain and any sensor errors first; do not change these values simply to hide an incorrect gear display.

Clutch-input plausibility

The TRSM clutch-diagnosis reference contains c_thd_pv_clu_act and c_thd_pv_clu_not_act, clutch-pedal-value thresholds, in percent, where the diagnostic expects the relevant switch to indicate activated and not activated. c_t_clu_swi_2_not_plaus is an implausibility debounce time in seconds. lv_clu_swi_2_not_plaus is a runtime flag associated with the second, interlock switch in this reference. These are diagnostic terms, not a universal pedal setting or a substitute for repairing wiring and hardware.

c_t_min_gear_chg_det_err_cs describes the minimum time of a pending changed gear for the gear-change-based clutch-switch diagnostic, in seconds; lv_cs_err_gear_chg_det records that a change was detected for this calculation. lv_cdn_diag_CS_PV identifies diagnostic conditions fulfilled. A monitor that has not run cannot demonstrate a pass; a flag requires the corresponding enabled conditions and software-specific interpretation. Do not disable start interlocks, plausibility checks or fault monitoring to make a tuning feature appear to work.

Logging and product-specific features

Record the ECU/gearbox identification, tyre and final-drive configuration, fault codes and freeze-frame data. In a safe stationary test, compare the scan tool's actual clutch-switch indication with pedal operation using the vehicle's service procedure. Where a controlled road or dynamometer test is appropriate, log RPM, vehicle speed, calculated and held gear if available, clutch state, pedal and throttle position, torque/boost request and actual, feature-enable and intervention states. Check whether the logged value is raw, filtered, calculated, held or transmitted. An RPM rise with clutch released can have several causes; a speed ratio alone does not prove clutch slip.

For example, simos.app Main Patch documents a patch-specific boost-limit-by-gear table and says the last gear is held during a shift. This behaviour is specific to that patch and version and is not proof that every factory or other aftermarket gear table behaves the same way. COBB's US-market Mk7 GTI FFS description describes holding a shift RPM limit when the clutch is depressed. Check exact feature enablement and its monitored conditions before attributing a failed feature to the clutch input.

In a 2016 manual GTI owner discussion, an EQT/COBB user reported that launch and flat-foot shifting did not work despite pressing the clutch. The report does not independently identify the ECU software, the actual switch state or a confirmed fix; it illustrates why feature readiness, configuration and input signals all need checking rather than assuming a bad switch.

Related: flat-foot shifting · torque and boost by gear · launch control · traction control · DSG torque coordination. References reviewed 17 November 2026.