Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Dodge, Ram

These examples concern the six-speed 68RFE automatic used with selected 6.7-litre Cummins Ram pickups. A 2014 truck and a separately identified 2022 modified truck illustrate different questions about shift pressure and torque-converter clutch (TCC) behaviour. Identify the actual transmission, controller, operating system and internal modifications; neither a 68RFE badge nor an engine tune establishes the correct transmission calibration.

Identify the vehicle, gearbox and controller

Ram's 2014 Ram 2500 specifications list the 6.7-litre Cummins diesel with a 68RFE six-speed automatic in one factory configuration. Other Ram configurations used different transmissions; check the vehicle identification, transmission code, software and actual hardware. Factory engine ratings are not targets for a modified truck.

In its June 2023 68RFE support announcement, HP Tuners describes separate CM2200, CM2350, CM2450 and early NGC4 transmission-controller groupings, with expanded shift scheduling, pressure, clutch-slip and TCC parameters. It identifies differences within the CM2450 period as well as differences across controller families. That announcement was specific to the releases and software it discussed; parameter names, exact availability, access hardware and licensing depend on the vehicle and current software. Verify the actual PCM/TCM and current supported-vehicle and controller list with HP Tuners, and do not apply a table from an Aisin or 48RE merely because the truck has a Cummins engine.

Shift scheduling, pressure and converter control

In a 2014 Ram 3500 68RFE discussion, an owner with a built transmission reported that the TCC moved from full to partial lock and back during shifts. A tutor described a pressure strategy for a separate 68RFE file using minimum and maximum pressures and a per-gear gain. The attached screenshot is restricted and was not reviewed. Those labels and the tutor's interpretation are a lead for that example, not proof of the table definitions or hydraulic limits in every controller. The thread's old claim about missing lockup tables should not be treated as a current VCM Suite limitation; HP Tuners subsequently documented expanded support in its 2023 announcement.

Separate the shift schedule (when the controller requests a shift), shift execution (clutch apply and release), line-pressure request and TCC state. A pressure request, gain or duty cycle is not the same thing as pressure measured at the relevant hydraulic circuit. Available channels and table units must be verified in the actual calibration. Consult the transmission builder about valve-body, relief and converter changes before using any pressure or timing value; do not assume an individual forum figure is safe for an unmodified unit.

Built transmission with a harsh 3–4 event

In a separate HP Academy case, the owner of a 2022 Cummins reported a built 68RFE, a triple-disc converter and an especially harsh 3–4 event after several transmission tunes. The owner said HP Tuners was being used. A tutor suggested logging line pressure and converter activity to establish whether lockup occurred before, during or after the shift. The thread does not establish a confirmed cause, a successful fix, the validity of a particular channel or a safe universal pressure. The tutor's pressure examples are specific to other hardware and are not targets for this truck.

Capture a repeatable event with requested and actual gear, engine and input/output speeds, accelerator or load, transmission temperature, TCC command and slip, and line-pressure request and feedback where the specific scanner exposes reliable values. Check timestamps and sampling rate. Mark when the shift is requested, how rpm changes, and whether converter application overlaps it. If pressure or TCC data are missing or implausible, use the correct service procedure and suitable independent test equipment. A harsh event may involve electrical, hydraulic, mechanical, engine-torque or calibration factors and requires diagnosis.

Builder requirements can differ

One HP Tuners-compatible commercial calibration advertises a changed converter-lock strategy for its listed application. A separate page reproducing RevMax's transmission warranty requirements warns against changing converter-lock application on its specified builds. These are product-specific statements from different businesses, not proof that either strategy is suitable for all 68RFEs. Confirm the exact builder's current requirements for the installed converter and valve body; inspect the vehicle's actual log and calibration rather than inferring behaviour from a product name.

Baseline and validation

  1. Before reading, record fault codes and freeze-frame; HP Tuners warns that a read can clear DTCs. Save the vehicle's own original supported files and log, noting transmission and PCM identities, tyres, axle ratio, fuel, load and all drivetrain modifications. HP Tuners: getting started.
  2. Review the exact truck's service history, fluid condition and relevant mechanical, wiring and hydraulic faults. A diagnostic display or commanded TCC state does not by itself prove physical clutch application. Check the current service and builder procedures before changing adaptations or calibration.
  3. Use only verified parameters for the actual file. Document each change and compare fresh logs under matching temperature, load and mode. Do not blindly revert a modified transmission to an unrelated factory calibration; its builder may require different support for its hardware.

Related: Ram pickup generations; 6.7 Cummins switch-on-the-fly modes; VCM Scanner; HP Tuners MPVI4.