Tuning Wiki
Browse Dodge Ram

HP Tuners switch-on-the-fly (SOTF) on the 6.7 Cummins uses map slots whose effect depends on per-group enables and engine-mode conditions, so a displayed active slot alone does not show which data governs a parameter. A 2019 6.7 Cummins owner using HP Tuners reported that a selected slot did not appear to explain the injection-timing information in the log, with several mode, override and slot channels reported at once; no verified answer is documented and the exact calibration was not examined. 2019 owner report.

Engine, gearbox and controller identification

The 2019 Ram Heavy Duty Cummins is a 6.7-litre turbocharged inline-six. In the announced 2019 pickup line, the standard-output diesel was paired with the electronically controlled 68RFE six-speed automatic; the high-output 3500 used an Aisin AS69RC six-speed automatic. Power and equipment vary by model, market and year: identify the fitted transmission and controller rather than inferring them from the engine name. Ram described a variable-geometry turbocharger and a compacted-graphite-iron block for its 2019 high-output engine. 2019 Ram Heavy Duty powertrain announcement.

Cummins specifies the separate 2019 Aisin-equipped 3500/4500/5500 chassis-cab engine as a 6.7-litre six-cylinder with charge-air cooling and Bosch high-pressure common-rail fuel system; its 360 hp and 800 lb-ft rating must not be substituted for a pickup rating. Cummins chassis-cab specifications.

HP Tuners announced CM2450B ECM support for selected 2022-24 RAM 2500-5500 trucks, requiring a specified ECM upgrade, compatible interface and Smart Access cable. Its notice also identifies AS69RC_B transmission-controller support on applicable Aisin trucks. Engine and transmission licences and available features are separate; this announcement alone does not establish that every CM2450B software version supports the SOTF features described below. Check the current compatibility list and exact controller. HP Tuners: CM2450B support.

A slot is only one part of the lookup

HP Tuners lists SOTF for selected 2013-18 6.7 Cummins CM2350 and 2019-24 CM2450 applications. Check the controller subtype, OS, interface, cable and service requirements for the specific truck. In HP Tuners' 2022 Cummins SOTF guide v1.6, initial slot data is copied from the corresponding Mode 1 table and switchable groups initially use the OEM lookup. Individual groups must be configured for OEM+SOTF where appropriate. The number of slots may be limited by the operating system. Application details; Cummins SOTF guide v1.6.

The same guide describes engine-mode-based groups that additionally depend on per-slot override conditions. Other listed groups do not use that mode override, subject to their SOTF enable configuration. Therefore, a displayed active slot alone does not prove which data is governing every parameter. Check the applicable group's enable state, the slot and engine-mode status, and the configured override conditions and thresholds. This does not resolve the 2019 owner's particular case.

The guide says Scanner can display Active Slot, and describes default-slot and maximum-slot settings. Its 2022 instructions for an OS modification require saving a new file, closing and reopening it, then following the specified first-write procedure exactly. Do not transfer settings or mode overrides from another OS; consult the current on-screen instructions and HP Tuners documentation for the vehicle. Incorrect OS-mod procedures can damage a controller.

Turbo and transmission cases that inform logging

On a modified fourth-generation 6.7 Cummins with compound turbos, an HP Tuners user found that lowering a minimum vane-position limit did not make the observed position fall to that minimum. A tuner explained that a minimum is a lower boundary within which the control strategy can still request another position; the reported advice involved the maximum and airflow model. This is a community interpretation for that build, not a validated universal algorithm or a target vane setting. First identify the calibration and compare requested and measured vane position, the relevant limits, airflow and operating conditions; investigate actuator or hardware faults before editing limits. Fourth-generation compound-turbo report.

A 2022 Cummins with a rebuilt 68RFE and aftermarket multi-disc converter showed a harsh 3-4 shift after several transmission tunes. The advice given was to log pressure and torque-converter clutch activity to see whether lockup occurs before, during or after the shift. No final repair is documented, and the pressures quoted describe a different transmission and must not be adopted as targets. Compare the vehicle's known calibration, build specifications and repeatable logs with the transmission builder's guidance, and diagnose hydraulic, electrical and mechanical causes before changing tables. 2022 68RFE report.

HP Tuners' 2023 release describes 68RFE support on selected Cummins applications, including shift schedules, pressure and duty-cycle controls, and torque-converter lockup/slip settings. These functions and their labels depend on the controller and software version; a table's presence does not determine the correct value for a rebuilt unit. Verify the exact TCM and current support rather than assuming 68RFE and Aisin calibrations are interchangeable. HP Tuners: 68RFE parameter support.

Earlier Cummins example: compare the actual changes

A 2005 Cummins owner reported a rough, stalling idle after a modified tune and normal running after restoring the original file; reversing the two changes a tutor suggested did not cure the modified tune, and the cause remained unresolved. This earlier truck is not a CM2350/2450 SOTF example. 2005 owner report.

For a known-good original and a modified file from the same vehicle, VCM Editor's Compare menu can display supported differences. HP Tuners notes that DTC differences are not compared and that cross-OS comparisons may omit or approximate some parameters. Use comparison to identify changes for investigation; it is not proof of the cause or permission to copy an unrelated file. Comparing two tune files; HP Tuners listing.

Not established

The reason the 2019 truck's slot did not explain its injection-timing data, the cause of the 2022 harsh 3-4 shift and the 2005 truck's rough idle are not established.

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.