Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Gearboxes
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 2

Removed text is struck through; added text is highlighted.

Bosch GS19.04 mechanical-shift electronic modules are reported on selected Ford Falcon and Territory 6HP26 mechatronic units. Old Jaguar's specialist list associates the GS19.04 M-shift with Bosch 0260550008 and ZF 0501213727 and lists Ford Falcon and Territory examples along with Land Rover and Jaguar examples. That is a specialist parts reference, not proof a shared part number has matching Ford software or a direct-fit donor.

General ZF 6HP mechatronic illustration, not a positively identified Ford unit: ZF Aftermarket service information 50324. Credit ZF Friedrichshafen AG; reproduced with user-confirmed permission.

Identification and compatibility

Record VIN, engine, gearbox specification, selector, electronic module part number and software identification. Some Ford products use other six-speed transmissions and control systems; neither a Ford six-speed name nor a 6HP26 marking proves that a particular GS19.04 number is installed. Do not assume Ford and Jaguar/Land Rover modules are programmable or interchangeable using the same file; compare the factory application and the tool's supported controller and software.

For a separate vehicle context see the Land Rover GS19.04 mechanical-shift page. The Jaguar GS19.04 E-shift example has a different identifier in the specialist's list.

Connector and pinout

No factory- or tool-manufacturer pinout for Bosch 0260550008 in a specific Ford Falcon or Territory application was verified in the sources reviewed. No cavity assignments are supplied here. Obtain the vehicle/VIN-specific 6HP26 wiring document and connector orientation: Jaguar 6HP diagrams do not establish Ford assignments.

Recalibration tools

PCMflash lists Ford 6HP26 under its Ford transmission module 85 with read/write/checksum functions in the manufacturer manual. Confirm the specific vehicle, TCM, supported software, connection method, licence and current tool documentation; the manual entry does not establish that every 0260550008 calibration is supported. File reading/writing and editing a calibration are separate functions.

Magicmotorsport FLEX lists 6HP bench duplication in its supported duplicable-units list. Duplication does not itself establish tune editing for this Ford application. Verify identification, power, programming and recovery requirements and preserve the original vehicle configuration before writing.

See the ZF 6HP family guide. Sources reviewed 17 November 2026.

Community fitting and fault report

In a 2020 Ford XR6 Turbo forum thread, an owner of a 2008 Falcon FG G6E reports dropping the 6HP26 mechatronic during service, after which the car would not select a gear and P0973 was recorded. The owner considers replacing a solenoid or using a donor unit; a respondent expressly says their suggestion is tentative. No final repair outcome or controller part number is established in the thread. It illustrates the need to protect the assembly and diagnose physical damage before programming, not a proven donor or reset procedure.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Bosch GS19.04 M-shift Ford ZF 6HP26 controller

Bosch GS19.04 mechanical-shift electronic modules are reported on selected Ford Falcon and Territory 6HP26 mechatronic units. Old Jaguar's specialist list associates the GS19.04 M-shift with Bosch 0260550008 and ZF 0501213727 and lists Ford Falcon and Territory examples along with Land Rover and Jaguar examples. That is a specialist parts reference, not proof a shared part number has matching Ford software or a direct-fit donor.

ZF 6HP mechatronic electronic module and connector sleeve
General ZF 6HP mechatronic illustration, not a positively identified Ford unit: ZF Aftermarket service information 50324. Credit ZF Friedrichshafen AG; reproduced with user-confirmed permission.

Identification and compatibility

Record VIN, engine, gearbox specification, selector, electronic module part number and software identification. Some Ford products use other six-speed transmissions and control systems; neither a Ford six-speed name nor a 6HP26 marking proves that a particular GS19.04 number is installed. Do not assume Ford and Jaguar/Land Rover modules are programmable or interchangeable using the same file; compare the factory application and the tool's supported controller and software.

For a separate vehicle context see the Land Rover GS19.04 mechanical-shift page. The Jaguar GS19.04 E-shift example has a different identifier in the specialist's list.

Connector and pinout

No factory- or tool-manufacturer pinout for Bosch 0260550008 in a specific Ford Falcon or Territory application was verified in the sources reviewed. No cavity assignments are supplied here. Obtain the vehicle/VIN-specific 6HP26 wiring document and connector orientation: Jaguar 6HP diagrams do not establish Ford assignments.

Recalibration tools

PCMflash lists Ford 6HP26 under its Ford transmission module 85 with read/write/checksum functions in the manufacturer manual. Confirm the specific vehicle, TCM, supported software, connection method, licence and current tool documentation; the manual entry does not establish that every 0260550008 calibration is supported. File reading/writing and editing a calibration are separate functions.

Magicmotorsport FLEX lists 6HP bench duplication in its supported duplicable-units list. Duplication does not itself establish tune editing for this Ford application. Verify identification, power, programming and recovery requirements and preserve the original vehicle configuration before writing.

See the ZF 6HP family guide. Sources reviewed 17 November 2026.

Community fitting and fault report

In a 2020 Ford XR6 Turbo forum thread, an owner of a 2008 Falcon FG G6E reports dropping the 6HP26 mechatronic during service, after which the car would not select a gear and P0973 was recorded. The owner considers replacing a solenoid or using a donor unit; a respondent expressly says their suggestion is tentative. No final repair outcome or controller part number is established in the thread. It illustrates the need to protect the assembly and diagnose physical damage before programming, not a proven donor or reset procedure.

Revision 2: Bosch GS19.04 M-shift Ford ZF 6HP26 controller

Bosch GS19.04 mechanical-shift electronic modules are reported on selected Ford Falcon and Territory 6HP26 mechatronic units. Old Jaguar's specialist list associates the GS19.04 M-shift with Bosch 0260550008 and ZF 0501213727 and lists Ford Falcon and Territory examples along with Land Rover and Jaguar examples. That is a specialist parts reference, not proof a shared part number has matching Ford software or a direct-fit donor.

ZF 6HP mechatronic electronic module and connector sleeve
General ZF 6HP mechatronic illustration, not a positively identified Ford unit: ZF Aftermarket service information 50324. Credit ZF Friedrichshafen AG; reproduced with user-confirmed permission.

Identification and compatibility

Record VIN, engine, gearbox specification, selector, electronic module part number and software identification. Some Ford products use other six-speed transmissions and control systems; neither a Ford six-speed name nor a 6HP26 marking proves that a particular GS19.04 number is installed. Do not assume Ford and Jaguar/Land Rover modules are programmable or interchangeable using the same file; compare the factory application and the tool's supported controller and software.

For a separate vehicle context see the Land Rover GS19.04 mechanical-shift page. The Jaguar GS19.04 E-shift example has a different identifier in the specialist's list.

Connector and pinout

No factory- or tool-manufacturer pinout for Bosch 0260550008 in a specific Ford Falcon or Territory application was verified in the sources reviewed. No cavity assignments are supplied here. Obtain the vehicle/VIN-specific 6HP26 wiring document and connector orientation: Jaguar 6HP diagrams do not establish Ford assignments.

Recalibration tools

PCMflash lists Ford 6HP26 under its Ford transmission module 85 with read/write/checksum functions in the manufacturer manual. Confirm the specific vehicle, TCM, supported software, connection method, licence and current tool documentation; the manual entry does not establish that every 0260550008 calibration is supported. File reading/writing and editing a calibration are separate functions.

Magicmotorsport FLEX lists 6HP bench duplication in its supported duplicable-units list. Duplication does not itself establish tune editing for this Ford application. Verify identification, power, programming and recovery requirements and preserve the original vehicle configuration before writing.

See the ZF 6HP family guide. Sources reviewed 17 November 2026.

Community fitting and fault report

In a 2020 Ford XR6 Turbo forum thread, an owner of a 2008 Falcon FG G6E reports dropping the 6HP26 mechatronic during service, after which the car would not select a gear and P0973 was recorded. The owner considers replacing a solenoid or using a donor unit; a respondent expressly says their suggestion is tentative. No final repair outcome or controller part number is established in the thread. It illustrates the need to protect the assembly and diagnose physical damage before programming, not a proven donor or reset procedure.