The supplied Ferrari California Workshop Manual describes both a seven-speed electrohydraulically controlled dual-clutch transmission (DCT) and a separate six-speed mechanical gearbox. This guide concerns the documented California DCT and its two lubrication systems; confirm the exact car, gearbox, assembly configuration and current Ferrari documentation before applying the service information. The F1 name or paddle shifts alone do not mean that this DCT uses the same single-clutch architecture as a 360 F1. Source: supplied california.pdf, PDF p. 436, section C1.01.
Two circuits, not one service fill
Ferrari's California workshop manual treats the gear and differential oil and the hydraulic clutch system fluid as separate service items. For the documented California, its sections A3.02–A3.03 name Shell Transaxle 75W-90 GL5 gear oil and Shell DCT F-3 clutch system fluid. Ferrari North America's later technical information 2620 likewise specifies separate draining and filling operations for the California DCT gear oil and clutch hydraulic fluid in its covered repair. Always check current approved specifications and revisions for the specific car; do not substitute generic gear oil or ATF based only on a similar name.
The manual shows versions with separate gear-oil and clutch-oil coolers and versions using a single combined heat exchanger. The common heat-exchanger assembly should not be mistaken for one shared fluid service fill. Identify the actual cooling layout and its pipes and unions before tracing a leak, ordering a part or planning a service. Supplied manual PDF pp. 442–443 and 519–520, sections C2.01 and C3.01.
Level checks depend on conditions
The California manual gives separate procedures and temperature conditions. For its gear-oil check it specifies the ATF fluid must not exceed 40 °C and coolant must be between 40 and 50 °C; its clutch-fluid check calls for approximately 60 °C ATF, not exceeding 80 °C, and the same coolant range. These are observations from the documented workshop procedure, not complete instructions or limits for California T, other models or a different manual revision. The procedures also specify vehicle position, operating state, relevant plugs and tools; use the complete current procedure and avoid a static cold-level guess. Source: local manual PDF pp. 53–55 and 66–67, sections A3.02–A3.03.
The gear-oil filling description also lists different approximate quantities for the documented single-exchanger and separate-exchanger versions and notes retained oil affects the quantity required. A stated fill quantity therefore does not by itself establish a correct level. Identify the version and follow the complete level-check procedure; document any leakage and resolve its cause.
Diagnosis and repair context
- Record the exact warning, driving conditions, requested and actual gear, temperatures, faults and freeze-frame data, vehicle and TCU identification, maintenance history and any previous fluid or gearbox work before clearing codes.
- Identify the leaking circuit and layout before topping up or disassembly. A fluid leak, shift complaint or fault code alone does not establish which internal unit failed; check supply voltage, connections, cooling and the documented diagnostic data as appropriate.
- Ferrari technical information 2620 describes a specific CCP replacement procedure for listed DCT applications and calls for a pre-diagnosis form, clean handling, dedicated equipment and separate circuit operations. It does not say that every shift complaint requires a CCP. See the Ferrari North America bulletin, pp. 1–3 and 50–52.
- The bulletin's specialist bench pressure checks and repair steps are applicable only to their stated empty-gearbox conditions and specified equipment. They are not an instruction to pressurise an assembled or filled vehicle system.
Ferrari DCT leak and fault classification
For the California and California T among its listed applications, Ferrari North America technical information 2389 describes separate diagnostic paths for oil leakage, NCR control-unit errors and gearbox/differential noise. Its pre-diagnosis form records leak location, symptoms, gearbox and clutch-oil levels, contamination and diagnostic results; it calls for diagnosis of external causes before assigning a fault to the DCT. The bulletin's level 1–3 leak categories depend on the identified location and repair procedure, not simply the amount of oil visible. Ferrari TI 2389, Managing DCT gearbox faults, pp. 1–8 and 18–20.
TI 2389 distinguishes the listed selector actuator, clutch-control and pressure-sensor faults from the listed gearbox speed-sensor faults and routes them to different repair levels. Ferrari's later TI 2621, gearbox speed sensor replacement describes model-specific speed-sensor kits and supersedes earlier speed-sensor instructions. A stored sensor-related code requires guided diagnosis and confirmation of the correct current instruction; it does not by itself prove that an entire gearbox or sensor must be replaced. Repair procedures and kit applicability must be checked for the individual car and current service policy.
The workshop manual contains separate procedures for the manual gearbox. Confirm the transmission before using a fluid specification or test. The local source is Ferrari California Workshop Manual, california.pdf, pp. 53–67, 436, 442–443 and 519–520; it is not uploaded to the wiki. See also dual-clutch flywheels, automated clutch control and the gearbox comparison.