Tuning Wiki
Browse Ferrari

The supplied Ferrari California Workshop Manual describes both a seven-speed electrohydraulically controlled dual-clutch transmission (DCT) and a separate six-speed mechanical gearbox. This guide concerns the documented California DCT and its two lubrication systems; confirm the exact car, gearbox, assembly configuration and current Ferrari documentation before applying the service information. The F1 name or paddle shifts alone do not mean that this DCT uses the same single-clutch architecture as a 360 F1. Source: supplied california.pdf, PDF p. 436, section C1.01.

Two circuits, not one service fill

Ferrari's California workshop manual treats the gear and differential oil and the hydraulic clutch system fluid as separate service items. For the documented California, its sections A3.02–A3.03 name Shell Transaxle 75W-90 GL5 gear oil and Shell DCT F-3 clutch system fluid. Ferrari North America's later technical information 2620 likewise specifies separate draining and filling operations for the California DCT gear oil and clutch hydraulic fluid in its covered repair. Always check current approved specifications and revisions for the specific car; do not substitute generic gear oil or ATF based only on a similar name.

The manual shows versions with separate gear-oil and clutch-oil coolers and versions using a single combined heat exchanger. The common heat-exchanger assembly should not be mistaken for one shared fluid service fill. Identify the actual cooling layout and its pipes and unions before tracing a leak, ordering a part or planning a service. Supplied manual PDF pp. 442–443 and 519–520, sections C2.01 and C3.01.

Level checks depend on conditions

The California manual gives separate procedures and temperature conditions. For its gear-oil check it specifies the ATF fluid must not exceed 40 °C and coolant must be between 40 and 50 °C; its clutch-fluid check calls for approximately 60 °C ATF, not exceeding 80 °C, and the same coolant range. These are observations from the documented workshop procedure, not complete instructions or limits for California T, other models or a different manual revision. The procedures also specify vehicle position, operating state, relevant plugs and tools; use the complete current procedure and avoid a static cold-level guess. Source: local manual PDF pp. 53–55 and 66–67, sections A3.02–A3.03.

The gear-oil filling description also lists different approximate quantities for the documented single-exchanger and separate-exchanger versions and notes retained oil affects the quantity required. A stated fill quantity therefore does not by itself establish a correct level. Identify the version and follow the complete level-check procedure; document any leakage and resolve its cause.

Diagnosis and repair context

  • Record the exact warning, driving conditions, requested and actual gear, temperatures, faults and freeze-frame data, vehicle and TCU identification, maintenance history and any previous fluid or gearbox work before clearing codes.
  • Identify the leaking circuit and layout before topping up or disassembly. A fluid leak, shift complaint or fault code alone does not establish which internal unit failed; check supply voltage, connections, cooling and the documented diagnostic data as appropriate.
  • Ferrari technical information 2620 describes a specific CCP replacement procedure for listed DCT applications and calls for a pre-diagnosis form, clean handling, dedicated equipment and separate circuit operations. It does not say that every shift complaint requires a CCP. See the Ferrari North America bulletin, pp. 1–3 and 50–52.
  • The bulletin's specialist bench pressure checks and repair steps are applicable only to their stated empty-gearbox conditions and specified equipment. They are not an instruction to pressurise an assembled or filled vehicle system.

Ferrari DCT leak and fault classification

For the California and California T among its listed applications, Ferrari North America technical information 2389 describes separate diagnostic paths for oil leakage, NCR control-unit errors and gearbox/differential noise. Its pre-diagnosis form records leak location, symptoms, gearbox and clutch-oil levels, contamination and diagnostic results; it calls for diagnosis of external causes before assigning a fault to the DCT. The historical bulletin's level 1–3 leak categories depend on the identified location and repair procedure, not simply the amount of oil visible. Ferrari's later TI 2622 explicitly cancels and replaces TI 2389; use the latest applicable service information rather than relying on the historical classification. Ferrari TI 2389, Managing DCT gearbox faults, pp. 1–8 and 18–20.

TI 2389 distinguishes the listed selector actuator, clutch-control and pressure-sensor faults from the listed gearbox speed-sensor faults and routes them to different repair levels. Ferrari's later TI 2621, gearbox speed sensor replacement describes model-specific speed-sensor kits and supersedes earlier speed-sensor instructions. A stored sensor-related code requires guided diagnosis and confirmation of the correct current instruction; it does not by itself prove that an entire gearbox or sensor must be replaced. Repair procedures and kit applicability must be checked for the individual car and current service policy.

Speed-sensor example: Ferrari’s replacement TI 2622 includes a separate gearbox-speed-sensor fault table for the listed California and California T applications. It identifies P0792 as an invalid even-shaft speed signal and P2746 as an invalid odd-shaft speed signal; the entries are distinct from the clutch-pressure sensor codes below. Record the exact NCR fault and operating conditions, check the current Ferrari test path and compare relevant signals before deciding which component has failed. These labels are specific to the cited Ferrari material and are not universal definitions for every DCT. Ferrari TI 2622, p. 15.

California T downshift noise and software campaign

Ferrari North America technical information 2499 / campaign 455 describes an electronically controlled gearbox software update intended to improve clutch control during downshifts and reduce mechanical gear noise on a specified production range that includes California T and California T HS. Ferrari also notes that some vehicles require a compatible engine-control software update because the engine and gearbox strategies interact. Check the exact assembly and VIN, campaign status, model and software against current Ferrari service information; a downshift noise does not prove the vehicle is affected or that a software update will correct mechanical wear. The historical version numbers are not a generic programming instruction.

Clutch-pressure sensor code examples

Ferrari North America technical information 2668 includes the California and California T among its listed DCT applications. Its diagnostic table distinguishes P0841–P0843 for the odd clutch 1 pressure-sensor signal from P0846–P0848 for the even clutch 2 pressure-sensor signal. It also lists related clutch-pressure command faults, for which sensor or solenoid problems are possible. Compare the complete fault report and specified electrical and pressure tests with the matching vehicle documentation: these code labels do not prove that a sensor or the complete gearbox has failed.

The historical bulletin describes a component-level CCP pressure-sensor repair path after diagnosis and manufacturer technical approval. For its two specified 40-bar clutch pressure sensors, it directs both sensors to be replaced together when that procedure applies. Check current Ferrari instructions, parts applicability and repair authorization for the individual car; the historical instruction is not an automatic repair for every pressure code or another manufacturer’s DCT.

CCP oil-temperature sensor fault codes

For its listed California and California T applications, Ferrari North America technical information 2623 identifies gearbox-controller P0938 as no signal, P0939 as too-low signal and P0940 as too-high signal from the radiator-outlet / gearbox-inlet oil-temperature sensor. The bulletin describes a component-level CCP temperature-sensor repair path following its specified diagnosis and manufacturer approval. These electrical-signal entries are distinct from actual high oil temperature and from the clutch-pressure sensor codes above. Record the complete fault and conditions and follow current Ferrari guidance before deciding whether the sensor, wiring or another cause needs attention; a code alone does not establish the failed component or justify replacing the complete gearbox.

The workshop manual contains separate procedures for the manual gearbox. Confirm the transmission before using a fluid specification or test. The local source is Ferrari California Workshop Manual, california.pdf, pp. 53–67, 436, 442–443 and 519–520; it is not uploaded to the wiki. See also dual-clutch flywheels, automated clutch control and the gearbox comparison.

See also the Ferrari 458 dual-clutch gearbox guide for its model-scoped fault and oil-leak examples; verify applicability for the exact vehicle.