A clutch connects the engine to the transmission while allowing controlled slip when the vehicle moves away and temporary separation when required. In a conventional manual car the driver operates the clutch pedal and gear lever. In an automated manual transmission (AMT), a controller commands actuators to operate the clutch and select gears; the driver may request shifts with a lever or paddles, or use an automatic mode if provided. The presence of paddles alone does not identify the transmission's internal design. ZF: clutch and transmission actuators.
Manual and automated control
In a conventional hydraulic manual clutch, the pedal acts on a master cylinder and hydraulic fluid moves a slave cylinder or concentric release mechanism. Other applications use a cable or other mechanical linkage. The release mechanism changes the force applied by the pressure plate, allowing the disc to slip or separate. The driver coordinates pedal position, engine speed and gear selection; see clutches and clutch types. ZF: manual hydraulic clutch control components.
An automated system takes over some or all of those actions. Actuators may be electric, electrohydraulic or, particularly in commercial vehicles, pneumatically assisted; construction differs by vehicle. Sensors and the transmission controller provide feedback on states such as gear selection, speed and actuator position, while the engine controller may coordinate torque changes. ZF: actuator roles; ZF: pneumatic ConAct example.
A typical single-clutch shift
The exact order and control strategy are vehicle-specific, but a simplified upshift illustrates the coordination:
- The controller checks the shift request, speed and operating conditions, and coordinates a reduction of engine torque as needed.
- The clutch is released sufficiently to unload the transmission. A shift actuator moves the selector and engages the requested ratio.
- Engine speed and clutch engagement are controlled as the clutch is brought back into contact, then torque is restored. A downshift may include a controlled engine-speed increase where the system provides it.
A conventional single-clutch AMT has a period during the shift when its engine-to-driven-wheels torque path is interrupted. The perceived pause depends on the system and conditions; a hybrid can use a separate electric drive to help fill the interruption. Do not assume every abrupt shift is normal, or that every system uses the same torque-reduction or throttle strategy. ZF: AMT interruption and hybrid torque support.
Single clutch, dual clutch and torque converter
- Single-clutch automated manual: a clutch and a manual-type gearset are operated automatically. A paddle command requests a shift; it does not necessarily move a gearbox selector directly.
- Dual-clutch transmission: two clutches connect two gear paths. A suitable next gear can be preselected on the inactive path and torque transferred between clutches. This can reduce interruption on those shifts, but the shift sequence and feel still depend on the conditions and design. Some clutches run dry and others wet. ZF: dual-clutch power flow.
- Torque-converter automatic: a different type of transmission may also offer a manual shift mode or paddles. Its fluid coupling and lock-up clutch have different operating and diagnostic roles; see torque-converter clutch diagnosis.
Volkswagen's earlier 0AM training example uses two dry friction clutches, but electrohydraulic mechatronics still operate them and the gear selectors. Dry clutch friction faces do not mean there is no hydraulic control circuit. This example should not be extended to every DCT. Volkswagen SSP 850123: 0AM.
What the controller learns
As the friction components and release mechanism change, a controller may need reference positions or an engagement point learned according to its specific design. An engagement or bite point is the region where the clutch begins to transmit useful torque; the controller uses its measured feedback and learned data to manage take-up. ZF describes travel-sensor and engagement-point calibration for its commercial-vehicle ConAct system, which is an example rather than a procedure for all cars. ZF: ConAct calibration.
After a repair, follow the exact vehicle's procedures, prerequisites and supported diagnostic tool for installation, bleeding, setup and adaptation. ZF specifies calibration after installation for the SACHS actuators covered in its service note; an adaptation reset is not a substitute for repairing a worn clutch, air leak, low supply voltage or mechanical fault. ZF also instructs technicians not to energise those actuators manually. ZF: actuator service information.
For model-specific examples, start with the F1-style gearbox guide index, which links detailed BMW SMG, Ferrari, Maserati, Alfa Romeo Selespeed and Fiat Dualogic diagnostic guides.
For manufacturer-specific examples, browse the electronic gearbox guide, including Selespeed, Ford, Mercedes-Benz, smart, Easytronic and Toyota MultiMode.
Diagnosing poor engagement or shifts
- Identify the exact transmission, controller, hardware and software; record prior repairs and clutch or actuator work. Capture fault codes and freeze-frame data before clearing them.
- Record when the problem occurs: cold or hot, selecting a gear, moving off, a particular upshift or downshift, reversing or under load. Establish whether it is a request rejected by the controller, a gear-selection problem, clutch slip, incomplete release, judder or engine torque delivery.
- Using the vehicle's documented diagnostic channels, compare requested and actual gear, clutch or actuator position, relevant speed signals, engine torque intervention and any applicable hydraulic or pneumatic pressure. Channel names and scaling are controller-specific.
- Check the electrical supply, connectors, mechanical clutch and release mechanism, correct fluid or air supply where fitted, leaks and engine faults as appropriate. Fault codes and symptoms alone do not establish which component is defective.
- Complete the specified repairs and learning procedures, then verify the original complaint under the relevant conditions using the manufacturer's road-test and safety instructions.
For examples of road-car single-clutch paddle-shift systems, see F1-style automated manual gearboxes: BMW, Ferrari, Maserati and Fiat, and the MCP automated manual gearbox. For double-clutch examples, see DQ200 clutch diagnosis and DQ250 clutch adaptation.