Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Injectors
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Injector catalogue › Diesel injectors › Diesel injector testing

Testing guides: On-vehicle checks | Common-rail bench testing | Equipment | Results and coding | Mechanical, unit and HEUI.

A common-rail injector report needs the exact part number, test plan and individual test conditions. Look at each delivery, return, leakage and electrical result against its own limit. A single “flow” number, a good-looking spray or a closely matched set cannot replace a full result for the required test points.

Read a bench report

FieldWhat to look for
IdentificationMaker, full injector number and suffix, serial or unit ID, original cylinder and existing code.
Test setupBench, software and plan revision, fluid, temperature, pressure, return back-pressure, actuation and adapters.
Test pointsSpecified idle, pilot, part/load or emissions points as applicable; actual and allowed range at each step.
Delivery and returnKeep nozzle delivery and back-leak results separate, with their own units, limits and operating conditions.
StatusPass/fail for each supported step, skipped or unavailable tests, faults, repair performed, final result and authorised or other test-plan basis.
CodeExisting marking and any new code, including whether it was read, generated or entered into the vehicle ECU.

For example, if an illustrative test plan specifies 40 ± 3 mm³ per injection at one stated point, the allowed range is 37–43 mm³. A result of 41 is within that one point; 36 is below it. Those values are invented to show the arithmetic and are not specifications for any injector. Even an injector within that point may fail another point or the leak test.

Units and comparisons

Delivery may be expressed as mm³ per injection or per test-plan stroke, mg per injection, or another unit specified by the bench. Return can be reported as volume per time, per stroke or in other plan-specific units. One mL is 1,000 mm³, but converting a per-injection quantity to a per-minute volume also needs the actual number of injections per minute: 20 mm³ per injection × 1,000 injections/minute = 20 mL/minute. This is an illustrative calculation, not an engine-speed assumption. A mass/volume conversion also needs the density of the test fluid at the relevant temperature.

Return quantity must not be substituted for nozzle delivery. Compare before and after using the same plan, fluid, temperature, pressures, drive and test point. An observed improvement after repair is useful only if the applicable full set of limits and required tests are also met.

Matching and fault interpretation

Several injectors can agree with each other and all be out of specification. Conversely, a difference between units can be allowed by a particular plan. Compare each result with the part-specific acceptance band first. Do not apply a universal percentage or port-petrol cc/min rating to diesel common-rail injectors. A result outside the band may indicate a mechanical, hydraulic, actuator or test-fixture issue; the bench's diagnostic procedure and repeatability checks decide the next step.

Correction code: two separate tasks

  1. Bench generation or grading: an appropriately equipped specialist runs the required test and coding procedure for an eligible injector. The resulting code describes that individual injector according to the selected programme. The bench and licence must support that exact family and procedure; an ordinary test report is not automatically an authorised code.
  2. Vehicle programming: where required, the replacement or serviced injector's correct code is entered into the ECU against its actual cylinder using the vehicle's specified diagnostic procedure. Verify the value and cylinder assignment before completing the job.

Examples of names include Bosch IMA/NIMA, Delphi C2i/C3i/C4i and DENSO compensation/ID codes; code formats and requirements vary. Delphi's coding explanation and DENSO's replacement warning describe why individual values are registered. Some parts do not use an individual code in the same way: DENSO describes a specific 2026 aftermarket range without individual QR calibration codes in this product bulletin. Follow the instructions for the actual part and vehicle rather than assuming all injectors are coded alike.

Hartridge explains that coding can require additional injector-specific measurement and temperature control in Coding 101. Use the new code only when produced by the relevant supported process. A code cannot fix a leaking, worn or untested injector.

After the bench

Keep the report with the unit. Fit the correct seals, pipes and fasteners in accordance with the vehicle maker's procedure and assess the fuel system for contamination. DENSO's replacement guidance stresses cleanliness, bore condition, coding where required, and the manufacturer's limits on high-pressure pipe reuse. After assembly, use the prescribed priming, leak checks, fault-code and running checks. A successful bench report cannot by itself clear an on-vehicle pump, wiring or compression fault.

Sources