Launch control, flat-shift and anti-lag are three engine-control functions that hold or build engine output while the driver keeps the accelerator down. Launch control holds a fixed engine speed at a standstill. Flat-shift, also called no-lift shift, briefly removes torque for a gear change without closing the throttle. Anti-lag keeps a turbocharger spinning when the engine would otherwise not supply enough exhaust energy.
All three work by making the engine produce less crankshaft torque than the air it is consuming would allow, by cutting or retarding ignition, cutting fuel, or closing an electronic throttle. The ignition-based methods move combustion into the exhaust, which is why they heat exhaust valves, manifolds, turbines and catalysts, and all three apply shock loads to the driveline. ECU manufacturers attach damage warnings to them. Family-specific behaviour is on ME7 launch control, no-lift shift and anti-lag, Simos 18 launch control, Simos 18 flat-foot shifting and DQ250 launch control conditions.
Launch control
Two-step limiters
The basic form is a second, lower rev limit that applies only while a launch condition is true, usually a clutch switch, a launch button or a vehicle-speed threshold. The driver holds full throttle against it and releases the clutch. The cut methods are the same as for any limiter and are described on rev limiters.
Speeduino documents a typical clutch-switch implementation with two stages. At a soft limit the ECU replaces the ignition angle with a fixed absolute timing, which slows the rise in engine speed but does not hold it. At a hard limit the ignition is cut completely until speed falls. A fuel adder can be applied while launch is active to help build boost (Speeduino: launch and flat shift).
Haltech describes the turbocharged variant. Its launch function substitutes a dedicated ignition table whose values are retarded near the launch speed, sometimes to around 20° after top dead centre, together with a fuel correction table. Combustion is then still in progress as the exhaust valve opens, so energy goes to the turbine instead of the piston and the engine builds boost while stationary. Haltech notes that this method has no air injection into the exhaust manifold and is distinct from rally anti-lag. It also notes that heavy retard is counter-productive on a torque-converter car held on the brake, which needs the engine to make torque against the converter (Haltech: how launch control works). Launch can be restricted by minimum coolant temperature, minimum throttle and maximum vehicle speed (Haltech: launch control).
Link lists three launch modes on its G4X ECUs: a single launch speed (two-step), a table-based latched speed, and a latched launch speed used for rolling launches (Link: motorsport features).
Factory launch programmes on dual-clutch gearboxes
Production launch control on a dual-clutch car is run by the gearbox controller. Audi's self-study programme for the six-speed 02E (DQ250) gives the sequence. The engine is held at a fixed launch speed with the clutch transmitting almost nothing, about 1 Nm, and when the brake is released the gearbox controller balances engine torque and clutch torque for maximum acceleration.
| Condition or value | Audi 02E example (SSP 386, technical status 10/2006) |
|---|---|
| Vehicle speed | 0 km/h |
| Gearbox oil temperature | Above 30 °C |
| Clutch temperature | Normal |
| Stability or traction control | Switched off |
| Selector | S or tiptronic |
| Brake | Applied, at least 20 bar brake pressure |
| Accelerator | Full throttle |
| Launch engine speed | About 3200 rpm naturally aspirated petrol, 2600 rpm TFSI, 2000 rpm TDI |
The programme states that its values are guidelines for the software current at publication. The figures are therefore examples for that gearbox and period (Audi SSP 386). The programme does not say how the engine controller holds the launch speed. A general summary describes launch control as a second rev limiter and states that drive-by-wire cars implement it through the electronic accelerator and software, while cable-throttle cars use fuel or spark cut (Wikipedia: Launch control). The ECU and gearbox torque exchange is covered on Simos 18 DSG torque coordination and gearbox and TCU tuning.
Flat-shift
Flat-shift lets the driver change gear on a manual gearbox with the accelerator fully depressed. A clutch switch tells the ECU that a shift has started. The ECU limits engine speed, by ignition retard and then cut, so the engine does not over-rev while unloaded, and restores torque when the clutch is released. The intended benefit on a turbocharged engine is that the throttle stays open, so less boost is lost across the shift than when the driver lifts; this is the purpose stated in tuner training material, and no measured comparison has been identified.
Launch and flat-shift usually share the clutch input, and the ECU has to decide which one is wanted. Speeduino uses a single engine-speed threshold: clutch pressed above it is treated as a flat-shift, below it as a launch. Its flat-shift has a soft window, typically 100 to 1000 rpm below that threshold, in which an alternative absolute ignition timing is applied. Speeduino's documentation adds that the switch should trigger as close to the clutch take-up point as possible.
Link groups flat shifting with its gear-shift control for H-pattern and sequential gearboxes, including electronic or pneumatic shifters and throttle blipping on electronic-throttle engines. In factory ECUs the torque reduction may be made by spark, fuel or throttle depending on the software, as the ME7 and Simos 18 pages describe.
Anti-lag
Anti-lag supplies the turbine with energy when the throttle is closed or nearly closed. The methods differ in where the air comes from (Wikipedia: Antilag system, which is flagged as lacking inline citations).
| Method | How it works | Notes |
|---|---|---|
| Ignition retard with fuel | Ignition is retarded heavily and fuel added, so the charge is still burning as it leaves the cylinder. | Needs air flow, so on its own it works mainly at open throttle: at launch or across a shift. |
| Throttle kick or throttle bypass | The throttle is held partly open, or air bypasses it, while ignition is retarded so far that little torque reaches the crankshaft. | The off-throttle rally method. Link lists electronic-throttle integration for its anti-lag. |
| Fresh-air or secondary-air system | Air is fed directly into the exhaust manifold, where it burns with rich exhaust gas ahead of the turbine. | Used on mid-1990s World Rally cars; needs valves and pipework on the manifold. |
| Turbo bypass valve | A one-way valve admits air to the throttle body from atmosphere when the intake is below atmospheric pressure. | Closer to a spool aid than a full anti-lag system. |
Haltech's E8 and E11 manual describes its rally mode in the same terms: fuel is enriched and timing retarded off-throttle and during gear changes, and the throttle plate or idle valve has to be set to pass a large amount of air. Because that air flow would otherwise raise idle speed, a "rotational idle" drops injection events in rotation between cylinders to hold speed down (Haltech E8/E11 manual). Link's equivalent is cyclic idle, listed as part of its anti-lag system.
Rolling anti-lag applies the launch strategy to a moving car: a held or latched engine-speed target with retarded ignition, armed by a switch, so the car can build boost at a constant road speed before a roll-race start. Link documents a latched launch speed for this purpose. No manufacturer description of its thermal effect beyond the general launch and anti-lag warnings has been identified.
Why these functions load the engine and exhaust
- Late combustion. Measurements on a turbocharged 1.8-litre Audi engine at 2500 rpm and full load showed that with late ignition part of the combustion takes place in the exhaust stroke and exhaust gas temperature rises (Tunka and Polcar, 2017). Launch and anti-lag retard is far later than the 18° before top dead centre that was the latest setting in that test, and lies outside the range it measured. The gas leaving the cylinder passes the exhaust valves, manifold and turbine in turn.
- Ignition cut. A cut cylinder passes unburned fuel and air into a hot exhaust, where it can burn in the manifold, turbine or catalyst. This is the source of the bangs and flames, and of catalyst overheating: see catalytic converters and performance.
- Manufacturer warnings. Haltech states that anti-lag and launch control can overheat the engine, exhaust system and valve train, and restricts the functions to experienced operators. The Wikipedia summary adds turbine wheel and exhaust manifold damage from combustion outside the cylinder, and turbocharger overspeed if the system is not controlled. None of these sources gives temperatures or component lives.
Extra fuel during launch is used partly to limit combustion temperature (Haltech). On a road engine the factory component-protection logic may respond to the same heat: see component protection and full-load lambda enrichment and exhaust gas temperature monitoring.
Drivetrain shock loads
A launch engages the clutch with the engine at speed and full throttle, and a flat-shift re-engages it without the driver having reduced torque. Haltech's warning lists the gearbox, driveshafts, differentials, clutch and crankshaft as parts that can be damaged or fail. The factory dual-clutch programme protects itself with temperature conditions on the gearbox oil and clutch. Whether a harder launch is quicker at all depends on traction: see power, weight and traction.
Road cars: legality, noise and catalysts
- Noise. In the United Kingdom it is illegal to modify an exhaust system to make a vehicle noisier after type approval, and the police can act when a vehicle is driven in a way that creates too much noise (GOV.UK: vehicle noise limits). An ignition-cut limiter or anti-lag used on the road falls plainly within the second point.
- Catalyst. Ignition-cut launch, flat-shift by spark cut and any anti-lag send unburned mixture to the catalyst. A road car that must keep its catalyst should use fuel cut or throttle-based torque reduction for these functions, or not use them.
- Protection. Limit activation by coolant temperature, time and vehicle speed where the ECU allows, and log exhaust temperature when setting them up.
Not established
- Exhaust temperatures and turbocharger or valve life under anti-lag for any named engine: the available sources are qualitative.
- Typical ignition angles for anti-lag: the 35 to 45° after top dead centre quoted in the Wikipedia article is uncited.
- Drivetrain load figures for launch or flat-shift.
- Manufacturer limits on the number of launches for particular models.
Sources
- Launch Control and Flat Shift. Speeduino manual source, page dated 8 April 2020. Two-step soft and hard limits, fuel adder, flat-shift window and the engine-speed threshold separating launch from flat-shift. Accessed 2026-11-19.
- How Launch Control Works. Haltech knowledge base, undated. Launch limiters, ignition retard to build boost, clutch against torque-converter cars, distinction from rally anti-lag. Accessed 2026-11-19.
- Launch Control. Haltech knowledge base, undated. Activation inputs, validation conditions, launch ignition and fuel tables, and damage warnings. Accessed 2026-11-19.
- Haltech E8/E11 user manual, anti-lag section. Haltech; third-party manual mirror, undated. Rally-mode anti-lag, air flow requirement, rotational idle and warnings. Accessed 2026-11-19.
- Motorsport features. Link Engine Management, undated. Launch modes including latched rolling launch, anti-lag with cyclic idle, and gear-shift control. Feature list only. Accessed 2026-11-19.
- Self-Study Programme 386: The 6-speed twin-clutch gearbox 02E (S tronic). Audi AG, technical status October 2006; independent PDF mirror. Launch Control Program conditions and launch speeds, page 80. Accessed 2026-11-19.
- Effect of Various Ignition Timings on Combustion Process and Performance of Gasoline Engine. L. Tunka and A. Polcar, Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis 65(2), 2017. Measured effect of late ignition on combustion in the exhaust stroke and exhaust temperature. Accessed 2026-11-19.
- Antilag system. Wikipedia, undated; flagged as lacking inline citations. Classification of anti-lag methods and qualitative damage statements. Accessed 2026-11-19.
- Launch control (automotive). Wikipedia, undated; flagged as needing more citations. Electronic-throttle launch limiting on production cars. Accessed 2026-11-19.
- Noise from roads, trains or planes: vehicle noise limits. GOV.UK, undated. Exhaust modification after type approval and police powers on noise. Accessed 2026-11-19.