Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Pontiac

Changes from revision 2 to revision 2

Removed text is struck through; added text is highlighted.

These HP Tuners examples focus on the 2004 Pontiac Grand Prix GTP 3.8 supercharged V6 and its automatic transaxle. They include separately identified 3800-family and swap reports, not settings to copy. Identify the actual vehicle, engine, PCM, software and gearbox, especially after a swap or rebuild.

Factory powertrain and HP Tuners support

Pontiac's 2004 Grand Prix brochure describes the GTP's 3800 Series III supercharged V6 with electronic throttle control, rated at 260 hp and 280 lb-ft in that US specification. The four-speed automatic was standard. The Competition Group included TAPshift and a 3.29 axle ratio; verify the installed gearbox and axle rather than assuming every GTP has that ratio. Pontiac 2004 brochure. A reproduced GM service reference identifies the GTP's supercharged 3.8 as L32 and the automatic as 4T65-E HD, RPO MN7; it records different 2004 transmission builds, ratios and converter details. Check the identification label and actual hardware. 4T65-E build and identification information.

HP Tuners lists 1997-2007 Grand Prix 3.1 and 3.8 applications. This broad entry does not prove support for every market, changed PCM, channel or transmission calibration. Confirm the actual PCM and OS, device requirements and licence against the current list before work. HP Tuners GM vehicle list.

Baseline before editing

Record diagnostic trouble codes and relevant freeze-frame before reading: HP Tuners says a vehicle read clears codes. Save the vehicle's own original supported calibration and note the PCM identity, pulley, injectors, fuel, exhaust and intake modifications. HP Tuners getting started. In VCM Scanner configure only channels the specific car provides. Record engine speed, load, MAF signal and calculated airflow with their units, manifold pressure where available, intake and coolant temperature, commanded enrichment, fuel trims in closed loop, ignition timing and knock-retard channels. Confirm the wideband and configuration before comparing measured lambda with a command; a narrowband oxygen sensor or a commanded AFR is not a measured high-load AFR. HP Tuners Scanner configuration. Investigate air leaks, fuel-pressure and injector condition, ignition faults, sensor plausibility and mechanical noise before treating a trim or knock value as a map error. Separate normal operation by temperature, load and closed-loop state; stop a loaded test if sustained knock or an unexpected lean condition appears.

Fuel trims and power enrichment on the 3800

An HP Tuners user working on a 3800 V6 asked whether stock-car trim deviations warranted changing the MAF, VE or injector tables, and how a time-dependent power-enrichment adder and stoichiometric AFR affected the result. The advice given was to avoid immediately changing stock airflow tables, and possible protection functions were discussed. The vehicle year and exact engine variant are not established, the attached tune could not be reviewed, and the proposed table interpretation is not independently verified for the L32. HP Academy 3800 V6 report.

The practical distinction is to verify fuel type, configured stoichiometric ratio and whether the displayed signal is commanded AFR, measured AFR or lambda. A different AFR reference can change displayed values without proving that the actual mixture changed. Trim can correct for faults and normal variation; it does not identify which component caused the correction. If a power-enrichment or temperature-protection table is present, check its actual definition, enable conditions and measured behaviour before considering any change. Do not remove fuel or protection just to make a display match an example.

Supercharger pulley and knock reports

Owners comparing L67 and L32 pulley choices (a 2006 supercharged car) and one reporting knock in hotter weather on a modified 2004 GTP raised a further question of whether the tuning program displays measured AFR. These are unverified reports from different vehicles, not evidence that any named pulley is safe on another engine or that a software command replaces a wideband sensor. Log knock retard, timing, temperature, load and fuel delivery for the actual hardware; record fuel and conditions and investigate before further increasing load. A low or absent reported knock value alone does not validate the entire tune. Grand Prix pulley report.

Transmission and speed-signal context

Log requested and actual gear, vehicle speed, engine speed, throttle/load, transmission temperature and converter-clutch command or slip if the actual PCM exposes them. Differentiate a shift request from the physical clutch or converter response; a command alone does not prove completion. Record tyre, sprocket, differential, converter and transmission build information before considering a speed or shift calibration.

A 1998 Grand Prix 3800 4T80-E swap report describes a 2005 replacement transmission, custom fabrication and an HP Tuners speed-signal/ratio correction. In a later update the owner reported correcting an input pulse count and achieving normal-feeling shifts and converter lockup under stated conditions. This is one altered vehicle and not evidence that its ratios, pulse values or wiring are applicable to the original 2004 4T65-E. Confirm sensor hardware, ratio, control compatibility and any changes against the exact build and service data.

A Cobalt transmission-swap report compares a 2006 Grand Prix file with a 2000 file and speculates about shift-solenoid control. Those assumptions were not shown to be validated by a completed compatible swap; a shared family name, apparent table or part number does not prove interchangeable solenoids, wiring or controls.

Not established

The correct response to stock-car trim deviations on the L32, safe pulley and knock limits, and interchangeability of 4T65-E solenoid control across vehicles are not established.

Related: Pontiac Grand Prix generations, Eaton M90 supercharger, VCM Scanner and HP Tuners MPVI4.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Pontiac Grand Prix GTP 3.8: HP Tuners knock, fuel and 4T65-E logging

These HP Tuners examples focus on the 2004 Pontiac Grand Prix GTP 3.8 supercharged V6 and its automatic transaxle. They include separately identified 3800-family and swap reports, not settings to copy. Identify the actual vehicle, engine, PCM, software and gearbox, especially after a swap or rebuild.

Factory powertrain and HP Tuners support

Pontiac's 2004 Grand Prix brochure describes the GTP's 3800 Series III supercharged V6 with electronic throttle control, rated at 260 hp and 280 lb-ft in that US specification. The four-speed automatic was standard. The Competition Group included TAPshift and a 3.29 axle ratio; verify the installed gearbox and axle rather than assuming every GTP has that ratio. Pontiac 2004 brochure. A reproduced GM service reference identifies the GTP's supercharged 3.8 as L32 and the automatic as 4T65-E HD, RPO MN7; it records different 2004 transmission builds, ratios and converter details. Check the identification label and actual hardware. 4T65-E build and identification information.

HP Tuners lists 1997-2007 Grand Prix 3.1 and 3.8 applications. This broad entry does not prove support for every market, changed PCM, channel or transmission calibration. Confirm the actual PCM and OS, device requirements and licence against the current list before work. HP Tuners GM vehicle list.

Baseline before editing

  1. Record diagnostic trouble codes and relevant freeze-frame before reading: HP Tuners says a vehicle read clears codes. Save the vehicle's own original supported calibration and note the PCM identity, pulley, injectors, fuel, exhaust and intake modifications. HP Tuners getting started.
  2. In VCM Scanner configure only channels the specific car provides. Record engine speed, load, MAF signal and calculated airflow with their units, manifold pressure where available, intake and coolant temperature, commanded enrichment, fuel trims in closed loop, ignition timing and knock-retard channels. Confirm the wideband and configuration before comparing measured lambda with a command; a narrowband oxygen sensor or a commanded AFR is not a measured high-load AFR. HP Tuners Scanner configuration.
  3. Investigate air leaks, fuel-pressure and injector condition, ignition faults, sensor plausibility and mechanical noise before treating a trim or knock value as a map error. Separate normal operation by temperature, load and closed-loop state; stop a loaded test if sustained knock or an unexpected lean condition appears.

Fuel trims and power enrichment on the 3800

An HP Tuners user working on a 3800 V6 asked whether stock-car trim deviations warranted changing the MAF, VE or injector tables, and how a time-dependent power-enrichment adder and stoichiometric AFR affected the result. The advice given was to avoid immediately changing stock airflow tables, and possible protection functions were discussed. The vehicle year and exact engine variant are not established, the attached tune could not be reviewed, and the proposed table interpretation is not independently verified for the L32. HP Academy 3800 V6 report.

The practical distinction is to verify fuel type, configured stoichiometric ratio and whether the displayed signal is commanded AFR, measured AFR or lambda. A different AFR reference can change displayed values without proving that the actual mixture changed. Trim can correct for faults and normal variation; it does not identify which component caused the correction. If a power-enrichment or temperature-protection table is present, check its actual definition, enable conditions and measured behaviour before considering any change. Do not remove fuel or protection just to make a display match an example.

Supercharger pulley and knock reports

Owners comparing L67 and L32 pulley choices (a 2006 supercharged car) and one reporting knock in hotter weather on a modified 2004 GTP raised a further question of whether the tuning program displays measured AFR. These are unverified reports from different vehicles, not evidence that any named pulley is safe on another engine or that a software command replaces a wideband sensor. Log knock retard, timing, temperature, load and fuel delivery for the actual hardware; record fuel and conditions and investigate before further increasing load. A low or absent reported knock value alone does not validate the entire tune. Grand Prix pulley report.

Transmission and speed-signal context

Log requested and actual gear, vehicle speed, engine speed, throttle/load, transmission temperature and converter-clutch command or slip if the actual PCM exposes them. Differentiate a shift request from the physical clutch or converter response; a command alone does not prove completion. Record tyre, sprocket, differential, converter and transmission build information before considering a speed or shift calibration.

A 1998 Grand Prix 3800 4T80-E swap report describes a 2005 replacement transmission, custom fabrication and an HP Tuners speed-signal/ratio correction. In a later update the owner reported correcting an input pulse count and achieving normal-feeling shifts and converter lockup under stated conditions. This is one altered vehicle and not evidence that its ratios, pulse values or wiring are applicable to the original 2004 4T65-E. Confirm sensor hardware, ratio, control compatibility and any changes against the exact build and service data.

A Cobalt transmission-swap report compares a 2006 Grand Prix file with a 2000 file and speculates about shift-solenoid control. Those assumptions were not shown to be validated by a completed compatible swap; a shared family name, apparent table or part number does not prove interchangeable solenoids, wiring or controls.

Not established

The correct response to stock-car trim deviations on the L32, safe pulley and knock limits, and interchangeability of 4T65-E solenoid control across vehicles are not established.

Related: Pontiac Grand Prix generations, Eaton M90 supercharger, VCM Scanner and HP Tuners MPVI4.

Revision 2: Pontiac Grand Prix GTP 3.8: HP Tuners knock, fuel and 4T65-E logging

These HP Tuners examples focus on the 2004 Pontiac Grand Prix GTP 3.8 supercharged V6 and its automatic transaxle. They include separately identified 3800-family and swap reports, not settings to copy. Identify the actual vehicle, engine, PCM, software and gearbox, especially after a swap or rebuild.

Factory powertrain and HP Tuners support

Pontiac's 2004 Grand Prix brochure describes the GTP's 3800 Series III supercharged V6 with electronic throttle control, rated at 260 hp and 280 lb-ft in that US specification. The four-speed automatic was standard. The Competition Group included TAPshift and a 3.29 axle ratio; verify the installed gearbox and axle rather than assuming every GTP has that ratio. Pontiac 2004 brochure. A reproduced GM service reference identifies the GTP's supercharged 3.8 as L32 and the automatic as 4T65-E HD, RPO MN7; it records different 2004 transmission builds, ratios and converter details. Check the identification label and actual hardware. 4T65-E build and identification information.

HP Tuners lists 1997-2007 Grand Prix 3.1 and 3.8 applications. This broad entry does not prove support for every market, changed PCM, channel or transmission calibration. Confirm the actual PCM and OS, device requirements and licence against the current list before work. HP Tuners GM vehicle list.

Baseline before editing

  1. Record diagnostic trouble codes and relevant freeze-frame before reading: HP Tuners says a vehicle read clears codes. Save the vehicle's own original supported calibration and note the PCM identity, pulley, injectors, fuel, exhaust and intake modifications. HP Tuners getting started.
  2. In VCM Scanner configure only channels the specific car provides. Record engine speed, load, MAF signal and calculated airflow with their units, manifold pressure where available, intake and coolant temperature, commanded enrichment, fuel trims in closed loop, ignition timing and knock-retard channels. Confirm the wideband and configuration before comparing measured lambda with a command; a narrowband oxygen sensor or a commanded AFR is not a measured high-load AFR. HP Tuners Scanner configuration.
  3. Investigate air leaks, fuel-pressure and injector condition, ignition faults, sensor plausibility and mechanical noise before treating a trim or knock value as a map error. Separate normal operation by temperature, load and closed-loop state; stop a loaded test if sustained knock or an unexpected lean condition appears.

Fuel trims and power enrichment on the 3800

An HP Tuners user working on a 3800 V6 asked whether stock-car trim deviations warranted changing the MAF, VE or injector tables, and how a time-dependent power-enrichment adder and stoichiometric AFR affected the result. The advice given was to avoid immediately changing stock airflow tables, and possible protection functions were discussed. The vehicle year and exact engine variant are not established, the attached tune could not be reviewed, and the proposed table interpretation is not independently verified for the L32. HP Academy 3800 V6 report.

The practical distinction is to verify fuel type, configured stoichiometric ratio and whether the displayed signal is commanded AFR, measured AFR or lambda. A different AFR reference can change displayed values without proving that the actual mixture changed. Trim can correct for faults and normal variation; it does not identify which component caused the correction. If a power-enrichment or temperature-protection table is present, check its actual definition, enable conditions and measured behaviour before considering any change. Do not remove fuel or protection just to make a display match an example.

Supercharger pulley and knock reports

Owners comparing L67 and L32 pulley choices (a 2006 supercharged car) and one reporting knock in hotter weather on a modified 2004 GTP raised a further question of whether the tuning program displays measured AFR. These are unverified reports from different vehicles, not evidence that any named pulley is safe on another engine or that a software command replaces a wideband sensor. Log knock retard, timing, temperature, load and fuel delivery for the actual hardware; record fuel and conditions and investigate before further increasing load. A low or absent reported knock value alone does not validate the entire tune. Grand Prix pulley report.

Transmission and speed-signal context

Log requested and actual gear, vehicle speed, engine speed, throttle/load, transmission temperature and converter-clutch command or slip if the actual PCM exposes them. Differentiate a shift request from the physical clutch or converter response; a command alone does not prove completion. Record tyre, sprocket, differential, converter and transmission build information before considering a speed or shift calibration.

A 1998 Grand Prix 3800 4T80-E swap report describes a 2005 replacement transmission, custom fabrication and an HP Tuners speed-signal/ratio correction. In a later update the owner reported correcting an input pulse count and achieving normal-feeling shifts and converter lockup under stated conditions. This is one altered vehicle and not evidence that its ratios, pulse values or wiring are applicable to the original 2004 4T65-E. Confirm sensor hardware, ratio, control compatibility and any changes against the exact build and service data.

A Cobalt transmission-swap report compares a 2006 Grand Prix file with a 2000 file and speculates about shift-solenoid control. Those assumptions were not shown to be validated by a completed compatible swap; a shared family name, apparent table or part number does not prove interchangeable solenoids, wiring or controls.

Not established

The correct response to stock-car trim deviations on the L32, safe pulley and knock limits, and interchangeability of 4T65-E solenoid control across vehicles are not established.

Related: Pontiac Grand Prix generations, Eaton M90 supercharger, VCM Scanner and HP Tuners MPVI4.