Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Infiniti, Nissan

HP Tuners lists selected Nissan 350Z and 370Z and Infiniti G37 applications in VCM Suite. This guide separates the manufacturer's coverage list from diagnostic and tuning observations on the VQ engine; it does not imply that every feature or transmission is supported. HP Tuners: Nissan and Infiniti coverage.

Identify the vehicle, engine and gearbox

HP Tuners' published vehicle table lists 2007-09 350Z VQ35HR, 2009-20 370Z VQ37VHR and 2008-15 Infiniti G37 VQ37VHR. These are vendor-listed examples, not a guarantee for every market, ECU or software version. HP Tuners cautions that some pre-2008 Nissan/Infiniti vehicles have older K-Line ECMs which are not supported: identify the actual ECM and check the current list and interface requirements before purchase or writing. Vehicle list and restrictions.

For example, Nissan describes the 2013 US-market 370Z coupe as a 3.7-litre VQ37VHR 24-valve DOHC V6 with VVEL variable valve event and lift, sequential port fuel injection and electronic throttle. The standard model was offered with a six-speed manual or seven-speed automatic; optional rev matching and engine output depend on the version. These are vehicle specifications, not evidence that HP Tuners supports tuning both transmissions. Confirm the installed gearbox and whether its controller can be read, logged or calibrated separately. Nissan: 2013 370Z specifications.

Before changing the calibration

  1. In VCM Scanner establish the correct vehicle profile, record trouble codes and a baseline log, and check which vehicle-specific channels actually update. HP Tuners warns that reading a vehicle clears DTCs, so record and investigate them first. In VCM Editor save the original read and confirm the controller and operating system before changing anything. HP Tuners: getting started.
  2. Record the fuel, intake, injector and exhaust changes. Confirm fuel pressure and sensor operation and investigate leaks or faults before using a fuel-trim difference as a calibration correction.
  3. Where available, log both banks' airflow and fuel corrections, engine speed, load and temperature. Check the units and channel source; a dashboard or histogram does not automatically add the corresponding input channel. Fuel trims apply only under the relevant closed-loop conditions. Independently verify mixture with suitable instrumentation under conditions where trims cannot establish it. HP Tuners: Scanner layouts.

370Z: bank-specific MAF diagnosis

Nissan's 2010 370Z VQ37VHR workshop manual distinguishes the two MAF circuits: P0102/P0103 for bank 1 and P010C/P010D for bank 2. Its procedure checks intake ducting and connections, supply, ground and signal circuits before condemning a sensor; it also calls for checking uneven airflow and intake/filter condition. For that manual's stock-vehicle test it gives approximately 0.4 V with ignition on and engine stopped, and 0.7-1.2 V at warm idle for each sensor. Use the Nissan procedure and test conditions, not these values as a universal modified-engine tuning target. The manual describes CONSULT-III and circuit checks, not a promise that HP Tuners exposes identically named PIDs. Nissan 2010 engine-control manual, EC-187-190.

EcuTek's separate 370Z guide explains that the two banks have different MAF scaling and recommends checking both. That is useful platform context when assessing an intake change or a bank imbalance, but its ProECU/RaceROM features, table names and procedures should not be assumed to exist in VCM Editor. Compare measured behaviour with the exact calibration and hardware rather than copying one bank's curve blindly. EcuTek: 370Z tuning guide.

Owner and vendor reports

A G37 owner reported attempting HP Tuners and having difficulty interpreting its ignition or burn-rate strategy before trying a different platform. This is one user's historical experience, not a verified current software limitation or an instruction to alter timing. Log available timing and knock-related channels, identify the actual calibration and verify current definitions before interpreting a change. 2022 G37 owner report.

An HP Tuners representative described the exposed parameters for a 2008 350Z with OS EV52D in 2018. That is a historical, single-OS example: its parameter count and features should not be assumed to apply to another file or today's release. HP Tuners' current vehicle list remains the starting point. 2018 350Z HP Tuners support announcement.

See also VCM Editor, VCM Scanner and MPVI4. Never flash a repository file intended for another vehicle; validate each change with fresh logs.