Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
Section level
Applies to
Maserati Biturbo
Tool groups
None
Manufacturers
Maserati

Changes from revision 4 to revision 5

Removed text is struck through; added text is highlighted.

Biturbo-era Maseratis changed from carburettor to electronic injection in 1986. This page records what the sources establish about each system. Factory jet sizes, ignition data and test figures are on factory service data, and factory ECU, sensor and turbo part numbers are on ECU, sensor and turbo part numbers. Connector pinouts and map data are still not established.Biturbo-era Maseratis changed from carburettor to electronic injection in 1986. This page records what the sources establish about each system. Factory jet sizes, ignition data and test figures are on factory service data. ECU part numbers, memory devices and connector pinouts are still not established.

Carburettor cars (1981–1986)

A single twin-choke Weber carburettor sits in a cast-alloy plenum that is pressurised by two small IHI turbochargers (type RHB51 with wastegate in the factory data). A 2.5 litre example is described with a computer-controlled wastegate, a maximum of 11 psi, 185 bhp and about 225 lb-ft at roughly 3,000 rpm. The factory carburettor is a Weber 36 DCNVH 16/100 (variants numbered 15, 26 and 27 for the 2.0, 2.0 S and 425). US-emissions cars used a Weber 34 instead, and a Weber 34 DAT is reported on 1986 2.5 litre cars and considered harder to keep in tune. One enthusiast table lists "42 DCNVH", which conflicts with the factory data. Jet sizes, float levels and the CO setting are given in the factory service data. Setting up the carburettor is regarded as fiddly once the turbos start to spool. General Weber information is on Weber DCNF, ICT and ICH and carburettor makes and model families. Because the carburettor sits upstream of the turbos, mixture and boost control affect each other; see MABC boost control and tuning.

Injection cars (1986 onward)

Injection arrived in 1986 with the Biturbo i and Si and the 420i. The factory describes a Weber IAW "Speed Density" system, meaning fuelling is calculated from manifold pressure and air temperature rather than an air flow meter. The injection control unit is identified as a Weber IAW 04C in the factory tester pages. The injected car uses two separate control units: an injection ECU at the front right of the central tunnel, and an ignition ECU under the dashboard on the passenger side. The ignition unit drives two coils directly from crank and cam sensors and a manifold-pressure tube; the distributor only distributes spark. The factory parts catalogue lists these as a "Marelli" ignition unit and a "Weber" injection unit with matching part numbers; see the part number page. The injection ECU takes manifold pressure, air temperature, coolant temperature, throttle position, cam position, engine speed and the knock sensor, hides a sealed CO adjusting screw, and cuts fuel at 6,300 rpm as the rev limiter. The Racing used Magneti Marelli controllers for ignition, injection and boost. The Ghibli uses direct ignition and a separate ignition and fuel ECU for each bank of three cylinders; the Shamal carries a Marelli IAW integrated ignition and injection ECU, one per cylinder bank. See 24-valve V6 and Shamal V8 engines. No ECU detail was found for the Quattroporte IV. A Marelli IAW 4CM is listed for the 3200 GT (1998 onward, outside this page's scope) and should not be assumed for earlier cars.Injection arrived in 1986 with the Biturbo i and Si and the 420i. The factory describes a Weber IAW "Speed Density" system, meaning fuelling is calculated from manifold pressure and air temperature rather than an air flow meter. The injected car uses two separate control units: an injection ECU at the front right of the central tunnel, and an ignition ECU under the dashboard on the passenger side. The ignition unit drives two coils directly from crank and cam sensors and a manifold-pressure tube; the distributor only distributes spark. The injection ECU takes manifold pressure, air temperature, coolant temperature, throttle position, cam position, engine speed and the knock sensor, hides a sealed CO adjusting screw, and cuts fuel at 6,300 rpm as the rev limiter. The Racing used Magneti Marelli controllers for ignition, injection and boost. The Shamal carries a Marelli IAW integrated ignition and injection ECU, one per cylinder bank. The Ghibli II also uses Weber-Magneti Marelli IAW injection and ignition. No ECU detail was found for the Quattroporte IV. A Marelli IAW 4CM is listed for the 3200 GT (1998 onward, outside this page's scope) and should not be assumed for earlier cars.

Typical electrical and ignition faults

The ignition ECU is a frequent suspect. A failed ignition module is often traced back to a faulty coil, so the coils should be tested or replaced together with a damaged unit. Bad earths and corroded connectors can also damage control units or cause intermittent running. A Weber/Marelli MAP sensor is part of the injection system.

A Maserati-club repair manual covers Weber IAW fault-finding for the 1989–93 4.24v; it is general rather than Maserati-specific, so check procedures against factory data.

Not yet established

Connector pinouts, EPROM types and map definitions for the control units. A reliable mapping of each control-unit part number to its AM engine code (the catalogue marks applicability in columns that are hard to read on the scans). Carburettor jetting for the 2.5 and later carburettor engines beyond the three variants in the factory table.ECU part numbers per model and year, connector pinouts, EPROM types and map definitions. Which IAW sub-variant belongs to which AM engine code. Carburettor jetting for the 2.5 and later carburettor engines beyond the three variants in the factory table.

Scans, part numbers and photographs with sources are welcome. Related: models and years, engines, airflow meter manufacturers.

References

Biturbo workshop manual: engine section Factory engine parts catalogue index Maserati Biturbo (Wikipedia) Maserati Shamal (Wikipedia) Maserati Classic: Biturbo Old Cars Weekly: Biturbo feature Biturbozentrum ECU discussionBiturbo workshop manual: engine section Maserati Biturbo (Wikipedia) Maserati Shamal (Wikipedia) Maserati Ghibli (Wikipedia) Maserati Classic: Biturbo Old Cars Weekly: Biturbo feature Biturbozentrum ECU discussion

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 4: Maserati Biturbo fuelling and ECU: Weber carburettors and Weber-Marelli IAW injection

Biturbo-era Maseratis changed from carburettor to electronic injection in 1986. This page records what the sources establish about each system. Factory jet sizes, ignition data and test figures are on factory service data. ECU part numbers, memory devices and connector pinouts are still not established.

Carburettor cars (1981–1986)

  • A single twin-choke Weber carburettor sits in a cast-alloy plenum that is pressurised by two small IHI turbochargers (type RHB51 with wastegate in the factory data). A 2.5 litre example is described with a computer-controlled wastegate, a maximum of 11 psi, 185 bhp and about 225 lb-ft at roughly 3,000 rpm.
  • The factory carburettor is a Weber 36 DCNVH 16/100 (variants numbered 15, 26 and 27 for the 2.0, 2.0 S and 425). US-emissions cars used a Weber 34 instead, and a Weber 34 DAT is reported on 1986 2.5 litre cars and considered harder to keep in tune. One enthusiast table lists "42 DCNVH", which conflicts with the factory data.
  • Jet sizes, float levels and the CO setting are given in the factory service data. Setting up the carburettor is regarded as fiddly once the turbos start to spool. General Weber information is on Weber DCNF, ICT and ICH and carburettor makes and model families.
  • Because the carburettor sits upstream of the turbos, mixture and boost control affect each other; see MABC boost control and tuning.

Injection cars (1986 onward)

  • Injection arrived in 1986 with the Biturbo i and Si and the 420i. The factory describes a Weber IAW "Speed Density" system, meaning fuelling is calculated from manifold pressure and air temperature rather than an air flow meter.
  • The injected car uses two separate control units: an injection ECU at the front right of the central tunnel, and an ignition ECU under the dashboard on the passenger side. The ignition unit drives two coils directly from crank and cam sensors and a manifold-pressure tube; the distributor only distributes spark.
  • The injection ECU takes manifold pressure, air temperature, coolant temperature, throttle position, cam position, engine speed and the knock sensor, hides a sealed CO adjusting screw, and cuts fuel at 6,300 rpm as the rev limiter.
  • The Racing used Magneti Marelli controllers for ignition, injection and boost.
  • The Shamal carries a Marelli IAW integrated ignition and injection ECU, one per cylinder bank. The Ghibli II also uses Weber-Magneti Marelli IAW injection and ignition.
  • No ECU detail was found for the Quattroporte IV. A Marelli IAW 4CM is listed for the 3200 GT (1998 onward, outside this page's scope) and should not be assumed for earlier cars.

Typical electrical and ignition faults

The ignition ECU is a frequent suspect. A failed ignition module is often traced back to a faulty coil, so the coils should be tested or replaced together with a damaged unit. Bad earths and corroded connectors can also damage control units or cause intermittent running. A Weber/Marelli MAP sensor is part of the injection system.

A Maserati-club repair manual covers Weber IAW fault-finding for the 1989–93 4.24v; it is general rather than Maserati-specific, so check procedures against factory data.

Not yet established

  • ECU part numbers per model and year, connector pinouts, EPROM types and map definitions.
  • Which IAW sub-variant belongs to which AM engine code.
  • Carburettor jetting for the 2.5 and later carburettor engines beyond the three variants in the factory table.

Scans, part numbers and photographs with sources are welcome. Related: models and years, engines, airflow meter manufacturers.

References

Revision 5: Maserati Biturbo fuelling and ECU: Weber carburettors and Weber-Marelli IAW injection

Biturbo-era Maseratis changed from carburettor to electronic injection in 1986. This page records what the sources establish about each system. Factory jet sizes, ignition data and test figures are on factory service data, and factory ECU, sensor and turbo part numbers are on ECU, sensor and turbo part numbers. Connector pinouts and map data are still not established.

Carburettor cars (1981–1986)

  • A single twin-choke Weber carburettor sits in a cast-alloy plenum that is pressurised by two small IHI turbochargers (type RHB51 with wastegate in the factory data). A 2.5 litre example is described with a computer-controlled wastegate, a maximum of 11 psi, 185 bhp and about 225 lb-ft at roughly 3,000 rpm.
  • The factory carburettor is a Weber 36 DCNVH 16/100 (variants numbered 15, 26 and 27 for the 2.0, 2.0 S and 425). US-emissions cars used a Weber 34 instead, and a Weber 34 DAT is reported on 1986 2.5 litre cars and considered harder to keep in tune. One enthusiast table lists "42 DCNVH", which conflicts with the factory data.
  • Jet sizes, float levels and the CO setting are given in the factory service data. Setting up the carburettor is regarded as fiddly once the turbos start to spool. General Weber information is on Weber DCNF, ICT and ICH and carburettor makes and model families.
  • Because the carburettor sits upstream of the turbos, mixture and boost control affect each other; see MABC boost control and tuning.

Injection cars (1986 onward)

  • Injection arrived in 1986 with the Biturbo i and Si and the 420i. The factory describes a Weber IAW "Speed Density" system, meaning fuelling is calculated from manifold pressure and air temperature rather than an air flow meter. The injection control unit is identified as a Weber IAW 04C in the factory tester pages.
  • The injected car uses two separate control units: an injection ECU at the front right of the central tunnel, and an ignition ECU under the dashboard on the passenger side. The ignition unit drives two coils directly from crank and cam sensors and a manifold-pressure tube; the distributor only distributes spark. The factory parts catalogue lists these as a "Marelli" ignition unit and a "Weber" injection unit with matching part numbers; see the part number page.
  • The injection ECU takes manifold pressure, air temperature, coolant temperature, throttle position, cam position, engine speed and the knock sensor, hides a sealed CO adjusting screw, and cuts fuel at 6,300 rpm as the rev limiter.
  • The Racing used Magneti Marelli controllers for ignition, injection and boost.
  • The Ghibli uses direct ignition and a separate ignition and fuel ECU for each bank of three cylinders; the Shamal carries a Marelli IAW integrated ignition and injection ECU, one per cylinder bank. See 24-valve V6 and Shamal V8 engines.
  • No ECU detail was found for the Quattroporte IV. A Marelli IAW 4CM is listed for the 3200 GT (1998 onward, outside this page's scope) and should not be assumed for earlier cars.

Typical electrical and ignition faults

The ignition ECU is a frequent suspect. A failed ignition module is often traced back to a faulty coil, so the coils should be tested or replaced together with a damaged unit. Bad earths and corroded connectors can also damage control units or cause intermittent running. A Weber/Marelli MAP sensor is part of the injection system.

A Maserati-club repair manual covers Weber IAW fault-finding for the 1989–93 4.24v; it is general rather than Maserati-specific, so check procedures against factory data.

Not yet established

  • Connector pinouts, EPROM types and map definitions for the control units.
  • A reliable mapping of each control-unit part number to its AM engine code (the catalogue marks applicability in columns that are hard to read on the scans).
  • Carburettor jetting for the 2.5 and later carburettor engines beyond the three variants in the factory table.

Scans, part numbers and photographs with sources are welcome. Related: models and years, engines, airflow meter manufacturers.

References