This page summarises the data in the factory Biturbo workshop manual, as reproduced in Italian and English on an enthusiast site (see References). The manual covers the 18-valve 2.0, 2.0 Si, 2.5 and 2.8 engines and the 2.24v; the exact model years it covers are not stated in the reproduced pages. Check against the manual for the exact model and market, since export cars differed. Values are summarised in tabular form, with the manual's own page numbers given for tracing.
Weber 36 DCNVH carburettor data (manual page 1-166)
| Item | 36 DCNVH 15 (2.0) | 36 DCNVH 26 (2.0 S) | 36 DCNVH 27 (425) |
| Venturi | 29 | 30 | 30 |
| Auxiliary venturi | 4.5 | 4.5 | 4.5 |
| Emulsion tube (F) | 55 | 59 | 59 |
| Main jet | 145 | 150 | 145 |
| Full-power (enrichment) jet | 110 | 110 | 110 |
| Idle jet | 52 | 50 | 60 |
| Max air bleed (idle air jet screw) | 190 | 200 | 205 |
| Min air bleed | 170 | 170 | 170 |
| Pump jet | 40 | 50 | 50 |
| Pump discharge | 50 | 40 | 50 |
| Pump cam | 42 | 42 | 42 |
| Needle valve | 250 | 250 | 250 |
| Idle mixture orifice | 130 | 190 | 180 |
| Advance orifice | 125 | 125 | 125 |
| Progression holes | 1 – 1.2 – 1.5 | 1 – 1.2 – 1.5 – 1.3 | 1 – 1.2 – 1.5 – 1.3 |
| Float weight | 6.5 g | 6.5 g | 6.5 g |
| Float level (no gasket) | 42.5 mm | 44 mm | 43.5 mm |
| Fuel valve adjustment, engine idling | 0.16 – 0.18 bar |
| CO at idle, warm engine | 1% |
| Boost-jet spring load | 130 g |
The fuel-system page of the same manual (page 0-28) lists the 2.0 carburettor as a 36 DCNVH 16/100 inverted twin-barrel with manual choke, with the same jet numbers as the first column and a float weight of 7.2 g, so float weight is given as both 6.5 g and 7.2 g. That page also gives the fuel pump (carburettor cars) as a Walbro 7509 electric pump, the tank as 80 litres (75 usable; 61 litres on first-series cars), and the turbochargers as two IHI RHB51 units with wastegates. This confirms the 36 size for the factory carburettor cars.
A later service note adds a flame-protection plate (factory part 32.22.32.427, with two nuts, two screws and two washers) to the carburettor on cars in service, and tells workshops to mark the plenum with an orange paint spot beside the Maserati badge once fitted.
Distributor and ignition (carburettor cars)
| Item | Figure |
| Distributor | Magneti Marelli SM 816 AX (single vacuum chamber) or SM 816 AXY (double chamber); rotor turns anticlockwise |
| Static advance | 12–13° BTDC at 900–1,000 rpm. A separate owner Q&A quotes 13° BTDC for European cars and notes US versions differ. |
| Maximum advance | 29° ± 1° as printed; the centrifugal and vacuum advance curves are published (vacuum advance of about 10° reached by roughly 100–150 mmHg) |
| Drive pinion end float | 0.05–0.15 mm |
| Rotor to pick-up gap | 0.5–0.6 mm |
| Coil | Magneti Marelli BAE 501 A; primary resistance 0.3 Ω ± 10%; secondary resistance printed as 5.4 ± 10% (unit not legible, most likely kilohms) |
| Ignition characteristics | Primary peak current about 5.5–6.5 A at 1,000 rpm; maximum secondary voltage about 20 kV |
Injected cars: distributor, plugs, ECUs
| Item | Figure |
| Distributor | Magneti Marelli DT 407 A, rotor anticlockwise; static advance 12° ± 1° BTDC at 1,000 rpm; drive pinion end float 0.1–0.3 mm |
| Coils | Two Magneti Marelli BAE 501 A units (A and B) driven directly by the ignition control unit; the distributor only distributes the spark |
| Sensors for ignition | Crankshaft sensor and camshaft sensor feed the ignition control unit; it also reads manifold pressure through a tube. It sets advance from an internal map against engine speed and load. |
| Ignition ECU location | Under the dashboard on the passenger side (raise the inner lining for access) |
| Injection system | Weber IAW, described as "Speed Density" (manifold pressure and air temperature based); electric fuel pump Weber PI 021/12 |
| Injection ECU location | Front right of the central tunnel (remove the tunnel lining) |
| Injection ECU inputs | Absolute manifold pressure, intake air temperature, coolant temperature, throttle position and movement, camshaft position, engine speed, knock sensor |
| Injection ECU outputs | Pulses to the individual injectors setting advance and duration of injection |
| CO adjustment | A tamper-proof plug on the front left of the injection control unit hides the CO adjusting screw |
| Rev limiter | The injection control unit cuts fuel at 6,300 rpm and restores it automatically below that |
Spark plugs
| Engine | Champion | NGK | Gap |
| 2.0 carburettor | N6YC or N6GY | – | 0.7 mm |
| 2.0 injected | N6YC or N6GY | BP8-ES | 0.7 mm |
| 2.0 Si | N6YC or N6GY | BP8-ES | 0.7–0.8 mm |
| 2.5 | N6YC | BP8-ES | 0.7–0.8 mm |
| 2.8 | N3C | BP8-ES | 0.7–0.8 mm |
| 2.24v | RA6YC | BP8-ES | 0.7–0.8 mm |
Valve clearances and cam data (cold)
| Engine | Inlet | Exhaust |
| 2.0 Biturbo / 2.0 i | 0.35 ± 0.04 mm | 0.45 ± 0.04 mm |
| 2.0 Si | 0.30–0.35 mm | 0.40–0.45 mm |
| 2.5 | 0.35 ± 0.04 mm | 0.45 ± 0.04 mm |
| 2.8 | 0.30–0.35 mm | 0.40–0.45 mm |
| 2.24v | 0.30–0.35 mm | 0.40–0.45 mm |
- Adjusting shims run from 2.10 mm to 4.475 mm in 0.025 mm steps.
- Valve stems are 7 mm. Head diameters are about 27 and 23–24.5 mm (inlet, small and large) and 35.5–37.1 mm (exhaust) on the three-valve engines; the 2.24v uses 33 mm inlets and 27.5 mm exhausts.
- Cam lift is 9.7 mm on the three-valve engines and 8.6 mm on the 2.24v. Camshaft end float is 0.10–0.15 mm.
Service procedures (page references)
- Fuel pressure (1-030): with a gauge on the regulator line, 2.5 bar is shown while the pump runs (about 9 seconds per cycle with the ignition on), and 2–2.2 bar at idle. After switching off, pressure should hold around 2 bar for at least 10 minutes. If it will not reach maximum, replace the two fuel filters then the pump; if it falls rapidly, replace the pressure regulator, then the pump.
- Idle speed and CO (1-024): warm to running temperature so the fans have cut in at least twice; switch off all electrical loads; with the exhaust analyser fitted, unplug the electromagnetic air valve. Idle should be 800–850 rpm with CO at 2.0–2.5%. Correct idle speed with the bypass screw on the throttle body only; the anti-crawl screw is factory set and not to be touched. Eliminate any air leak in the intake or vacuum lines first.
- Throttle potentiometer (1-026): unplug, disconnect the accelerator cable, loosen the mounting screws, rotate the potentiometer clockwise and release it a few times, tighten the screws without moving it, reconnect, then check smooth full opening and closing.
- Spark advance check (1-028): set the flywheel at the 10° advance mark and check that the crankshaft sensor lines up with an air gap on the pulley; the gap between sensor and pulley should be 0.7–1.1 mm, adjusted with 0.2 mm shims.
- Distributor refitting (1-028): bring cylinder 6 to top dead centre on compression, make sure the valves are balanced on the left bank, and align the lower rotor opening (cylinders 1-2-3) with the housing mark, with the distributor position mark turned toward the engine centre in the thermostat-body direction.
Lubrication and cooling (page 0-26)
- Hot oil pressure is 2.5–4 kg/cm²; the relief valve is set at 4 kg/cm². Filtering is by a gauze on the pickup and a full-flow Easy Change type filter.
- Two electric cooling fans on a thermostatic switch, operating at about 77–82°C; separate expansion tank; circuit pressure 0.9 bar; thermostat starts opening at 70 ± 2°C; the water pump is driven by the timing belt.
Not established
- ECU part numbers and connector pin lists; the manual includes a schematic wiring diagram (page 0-22), but its pin lists are not transcribed here.
- Specific data for the later 24-valve 2.8 and 4v cars.
- The maintenance-schedule and torque figures of the same manual are on a separate page.
References
Related: fuelling and ECU, Maserati Biturbo hub.