Tuning Wiki

Alongside the flagship DCOE, IDF, IDA and DGV ranges, three other Weber families see widespread workshop and tuning use: the compact synchronous twin-choke downdraft DCNF (famous on Italian V6/V8s and European hot hatches) and the single-barrel 34 ICT and 34 ICH conversion carburettors.

Adjustment screw diagrams

Simplified exploded screw reference for Weber 40 DCNF 12
Weber 40 DCNF 12: idle mixture screw 46 and throttle-stop screw 50. Original schematic for Tuning Wiki, CC BY 4.0, based on the Weber parts drawing and key. Screws are shown separately to identify the parts, not their exact assembled locations.
Simplified exploded Weber 34 ICT showing the idle mixture adjustment screw
Weber 34 ICT: idle mixture adjustment screw, item 24. Original schematic for Tuning Wiki, CC BY 4.0, based on the Weber 34 ICT parts drawing and key. The screw is shown separately for identification; the simplified view is not an exact assembled locator.
Simplified exploded Weber 34 ICH diagram highlighting mixture screw 32 and throttle stop screw 23
Weber 34 ICH: the idle-mixture screw and throttle-stop screw shown separated from the body. Original simplified redraw for Tuning Wiki, CC BY 4.0; see Carburetion.com’s 34 ICH parts drawing and key, items 32 and 23. This diagram is an exploded illustration, not an exact assembled locator; layouts vary.

Use the parts key alongside each exploded view; numbering applies only to the linked drawing.

Match the model and parts key before working on the carburettor; these are exploded views, so screw orientation can differ from the assembled view.

1. Weber DCNF (36 / 40 / 42 / 44 DCNF)

The Weber DCNF is a compact, low-height synchronous two-barrel downdraft carburettor whose float chamber runs crosswise beside the venturis for tight engine-compartment packaging. It was OEM equipment on the Fiat Dino V6, Ferrari 246 Dino and 308 GT4/GTB, Lamborghini Urraco, Maserati Ghibli/Merak, and Chrysler/Talbot/Simca models, and is a popular transverse twin-carb fitment.

Weber 36 DCNVA twin-choke downdraft carburettor on a Matra Murena 1.6
For comparison, a Weber 36 DCNVA twin-choke downdraft carburettor on a Matra Murena 1.6; the source identifies it as DCNVA, not DCNF. Photo: Uberprutser, Wikimedia Commons, CC BY-SA 3.0.
Model (example)Choke / auxMain jetEmulsion tubeAir correctorIdle jetPump / needleFloat (closed / drop)
36 DCNF 17/18 (Chrysler France)29 mm / 3.5120F361854540 / 1.7552 / 58.5 mm
40 DCNF 12 (Fiat Dino V6)32 mm (or 30) / 4.5125F242205045 / 1.7550 / 58.1 mm
42 DCNF 9 (Maserati Ghibli)34 mm / 3.5140F251806040 / 2.0048 / 58.5 mm
44 DCNF 44 (Maserati Merak)36 mm / 3.5140F251706540 / 2.0048 / 58.5 mm
  • DCNF jet parts & tuning: DCNF main jets are Weber 41115.003 (73405—different length/thread from DCOE/IDF 41110.001). Plastic floats typically set around 42 mm closed / 55 mm drop (Bigorre float chart). Multi-carb DCNF banks follow the same barrel-by-barrel Lean Best Idle and Synchrometer balancing sequence as IDF carbs.

2. Weber 34 ICT (dual single-barrel conversions)

The Weber 34 ICT is a compact single-barrel downdraft carburettor without a choke plate, sold primarily in twin-carburettor hex-bar kits for air-cooled VW Type 1, Type 3 and Type 4 engines (1,600–2,000 cc).

  • Baseline jetting: 27 mm or 29 mm venturi (4.5 aux), 130–135 main jet, F78 emulsion tube, 160 air corrector, 50–60 idle jet, 50 pump jet (40 bleed), 1.75 needle valve (CB Performance chart; Top End chart).
  • Float & fuel pressure: 6.5 mm closed / 13 mm drop (Weber jetting chart); keep fuel pressure regulated to 2.5–3 psi.
  • Tuning approach: because a pair of 34 ICTs shares the same single-barrel simplicity with one mixture screw and one idle speed screw per side, disconnect the hex-bar linkage first, set both throttle stops cleanly at low idle, balance airflow with a Synchrometer at both idle and ~2,500 rpm (checking hex-bar arm symmetry), and tune each mixture screw to Lean Best Idle. With no choke flap, cold starting relies on a couple of accelerator-pump primes before cranking.

3. Weber 34 ICH (single-barrel replacement carb)

The Weber 34 ICH is a manual-choke single-barrel downdraft replacement widely fitted to Land Rover Series IIA/III 2,286 cc, Ford Cortina/Escort/Capri 1.1/1.3/1.6, Saab V4 1,498 cc, Bedford CF 2.3 L, and Audi 80/VW Passat conversions (Eurocarb Weber applications).

Weber single-barrel conversion carburettor fitted to a Land Rover 2.25 engine
Weber carburettor mounted on a Land Rover engine; the photographer does not identify its model. Photo: Lewis Collard, Wikimedia Commons, CC0.
  • Baseline jetting: depending on kit specification, 25 mm or 29 mm venturi (4.5 or 3.5 aux), 130–165 main jet, F6 emulsion tube, 150–190 air corrector, 50–57 idle jet, 50–55 pump jet (40 bleed), 1.75 needle valve, and 6.5 mm / 13 mm float height.
  • Tuning approach: confirm the manual choke cable releases completely so the strangler flap sits fully vertical when warm, keep fuel pressure around 2.5–3 psi, set idle mixture to Lean Best Idle with the speed screw kept minimal, and tune main jet / F6 emulsion / air corrector using loaded road/dyno AFR checks.

4. Related pages

Sources