CP3 is a Bosch three-plunger radial common-rail high-pressure pump. Its metering unit controls fuel entering the pumping elements, while the rail, pressure sensor, pressure-control hardware and DDE work together to meet the requested pressure. Pump output depends on shaft speed, inlet conditions, pressure, temperature and wear: an advertised pump size or power rating does not determine installed fuel delivery. Bosch common-rail catalogue.
Identification: Record the complete Bosch 0 445 … number and the vehicle/VIN, engine, drive, mounting and metering valve. Similar CP3 family labels do not establish interchangeability. Verify rotation, mounting, drive coupling, inlet, return, electrical control and rail-pressure limits against the part-specific catalogue and installer. BMW identifies Bosch 0 445 010 194 as the CP3 16/3 pump for the US M57TU2 TOP, without establishing that all markets or engines have the same pump. BMW engineering information.
R90 identification and examples
R90 is a type designation used for a number of CP3 pumps, not one universal pump. Bosch training records 0 445 010 073 as BMW CR/CP3S3/R90/30-89S. Its list also records R90 pumps for other manufacturers with different part numbers and suffixes. Check the complete number, drive, ports and metering valve; an R90 from another engine must not be assumed to fit an M57. Bosch CP3 training and parts list.
An R90 upgrade is commonly selected when the existing pump cannot sustain the desired rail pressure at the required delivery. Actual flow must be compared at matched shaft speed, pressure, fuel temperature and supply conditions, using a test report for the exact pumps. The R90 label alone does not prove a particular pressure rating, percentage gain or horsepower ceiling. Confirm the installed original pump before treating an R90 as an upgrade.
Audi and Volkswagen CP3 R90 examples
Bosch's CP3 training list identifies 0 445 010 090 and 0 445 010 125 as Audi CR/CP3S3/R90/20-789S examples. The full pump number, not just “R90”, is required when ordering or planning an adaptation. Bosch CP3 training list.
For 0 445 010 125, a Bosch diesel specialist lists, among other applications, Audi A4 B7 3.0 TDI BKN (2005–06), A6 C6 3.0 TDI BMK (2004–06), and specified A4/A6 2.7 TDI BPP/BSG examples. These are catalogue examples, not a claim for all 2.7/3.0 TDIs or model years. Verify VIN, actual fitted number and supersession. Tyrone Diesel application list; Volkswagen Group six-cylinder diesel guide.
Some builders consider pumps from other applications for conversions. An Audi R90 and BMW R90 sharing a type family do not establish direct M57 interchangeability. Confirm shaft and drive, rotation, flange, pulley or sprocket, metering valve, inlet/return and high-pressure connections, mounting and calibration against the specific conversion kit. No confirmed bolt-on Audi-to-M57 application is established here.
Single and dual-pump installations
A single-pump conversion must match the engine drive, mounting, fuel fittings, metering control and rail system. On a dual setup, a second driven CP3 adds potential delivery but requires a compatible controller, secure high-pressure lines, sufficient low-pressure supply and a calibration that controls the complete system. More pump capacity does not by itself improve airflow or injector capacity. Santjer's example offers R70/R90 combinations but states verified fitment only for the North American 335d; it excludes the X5 accessory layout. Compare R70 and other CP3 variants.
Diagnosis and installation
Log requested and actual rail pressure under repeatable load and look at associated fuel-metering and rail-pressure faults. Before condemning a pump, check low-pressure supply and filter, air entry, restrictions, electrical supply and metering control, injector return leakage and rail pressure-control components. A fall in rail pressure is a system symptom, not proof of a failed pump.
Common-rail fuel can remain at very high pressure after shutdown. Use the vehicle-specific depressurisation and clean-work procedures, approved high-pressure lines and specified tightening/replacement instructions. Never loosen a live high-pressure connection to find a leak or use hands to check for leaks. After a pump failure, assess contamination throughout the fuel system and follow the manufacturer's repair and cleaning plan.
See fuelling faults, common-rail supply pumps and the M57 twin-turbo guide.