Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engines
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

CP3 is a Bosch three-plunger radial common-rail high-pressure pump. Its metering unit controls fuel entering the pumping elements, while the rail, pressure sensor, pressure-control hardware and DDE work together to meet the requested pressure. Pump output depends on shaft speed, inlet conditions, pressure, temperature and wear: an advertised pump size or power rating does not determine installed fuel delivery. Bosch common-rail catalogue.

Identification: Record the complete Bosch 0 445 … number and the vehicle/VIN, engine, drive, mounting and metering valve. Similar CP3 family labels do not establish interchangeability. Verify rotation, mounting, drive coupling, inlet, return, electrical control and rail-pressure limits against the part-specific catalogue and installer. BMW identifies Bosch 0 445 010 194 as the CP3 16/3 pump for the US M57TU2 TOP, without establishing that all markets or engines have the same pump. BMW engineering information.

R70 identification and examples

R70 identifies a group within Bosch CP3 pump type designations, not a complete order number or an engine-wide specification. The Bosch CP3 training list records 0 445 010 045 as CR/CP3S3/R70/20-789S for BMW, and 0 445 010 126 as CR/CP3S3/R70/20-89S for BMW. Differences in the complete suffix and associated parts matter. Verify the particular vehicle and supersession using Bosch or BMW data. Bosch CP3 training, parts list.

The US M57TU2 TOP engineering record lists 0 445 010 194 as CP3 16/3; it does not itself label that unit R70. Do not infer an R70 or R90 designation from a model badge or this engineering number without a part-specific cross-reference. BMW engineering information.

Upgrade choices

A healthy R70 may be retained if measured pressure and supply meet the intended calibration. If evidence shows insufficient delivery, a suitable R90, a specialist-modified pump or a dual-CP3 system may be considered. Compare bench flow at the same test pressure and shaft speed, not just a quoted percentage. Verify the fittings, drive and metering-control compatibility; a larger pump is not automatically a bolt-on swap.

The Whitbread 2009–11 US 335d kit describes a second R70 or R90 with its own controller and drive. This is evidence for that kit's stated application, not every 535d or X5. See the R90 page and CP3 family guide.

Diagnosis and installation

Log requested and actual rail pressure under repeatable load and look at associated fuel-metering and rail-pressure faults. Before condemning a pump, check low-pressure supply and filter, air entry, restrictions, electrical supply and metering control, injector return leakage and rail pressure-control components. A fall in rail pressure is a system symptom, not proof of a failed pump.

Common-rail fuel can remain at very high pressure after shutdown. Use the vehicle-specific depressurisation and clean-work procedures, approved high-pressure lines and specified tightening/replacement instructions. Never loosen a live high-pressure connection to find a leak or use hands to check for leaks. After a pump failure, assess contamination throughout the fuel system and follow the manufacturer's repair and cleaning plan.

See fuelling faults, common-rail supply pumps and the M57 twin-turbo guide.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Bosch CP3 R70 high-pressure fuel pumps

CP3 is a Bosch three-plunger radial common-rail high-pressure pump. Its metering unit controls fuel entering the pumping elements, while the rail, pressure sensor, pressure-control hardware and DDE work together to meet the requested pressure. Pump output depends on shaft speed, inlet conditions, pressure, temperature and wear: an advertised pump size or power rating does not determine installed fuel delivery. Bosch common-rail catalogue.

Identification: Record the complete Bosch 0 445 … number and the vehicle/VIN, engine, drive, mounting and metering valve. Similar CP3 family labels do not establish interchangeability. Verify rotation, mounting, drive coupling, inlet, return, electrical control and rail-pressure limits against the part-specific catalogue and installer. BMW identifies Bosch 0 445 010 194 as the CP3 16/3 pump for the US M57TU2 TOP, without establishing that all markets or engines have the same pump. BMW engineering information.

R70 identification and examples

R70 identifies a group within Bosch CP3 pump type designations, not a complete order number or an engine-wide specification. The Bosch CP3 training list records 0 445 010 045 as CR/CP3S3/R70/20-789S for BMW, and 0 445 010 126 as CR/CP3S3/R70/20-89S for BMW. Differences in the complete suffix and associated parts matter. Verify the particular vehicle and supersession using Bosch or BMW data. Bosch CP3 training, parts list.

The US M57TU2 TOP engineering record lists 0 445 010 194 as CP3 16/3; it does not itself label that unit R70. Do not infer an R70 or R90 designation from a model badge or this engineering number without a part-specific cross-reference. BMW engineering information.

Upgrade choices

A healthy R70 may be retained if measured pressure and supply meet the intended calibration. If evidence shows insufficient delivery, a suitable R90, a specialist-modified pump or a dual-CP3 system may be considered. Compare bench flow at the same test pressure and shaft speed, not just a quoted percentage. Verify the fittings, drive and metering-control compatibility; a larger pump is not automatically a bolt-on swap.

The Whitbread 2009–11 US 335d kit describes a second R70 or R90 with its own controller and drive. This is evidence for that kit's stated application, not every 535d or X5. See the R90 page and CP3 family guide.

Diagnosis and installation

Log requested and actual rail pressure under repeatable load and look at associated fuel-metering and rail-pressure faults. Before condemning a pump, check low-pressure supply and filter, air entry, restrictions, electrical supply and metering control, injector return leakage and rail pressure-control components. A fall in rail pressure is a system symptom, not proof of a failed pump.

Common-rail fuel can remain at very high pressure after shutdown. Use the vehicle-specific depressurisation and clean-work procedures, approved high-pressure lines and specified tightening/replacement instructions. Never loosen a live high-pressure connection to find a leak or use hands to check for leaks. After a pump failure, assess contamination throughout the fuel system and follow the manufacturer's repair and cleaning plan.

See fuelling faults, common-rail supply pumps and the M57 twin-turbo guide.

Revision 1: Bosch CP3 R70 high-pressure fuel pumps

CP3 is a Bosch three-plunger radial common-rail high-pressure pump. Its metering unit controls fuel entering the pumping elements, while the rail, pressure sensor, pressure-control hardware and DDE work together to meet the requested pressure. Pump output depends on shaft speed, inlet conditions, pressure, temperature and wear: an advertised pump size or power rating does not determine installed fuel delivery. Bosch common-rail catalogue.

Identification: Record the complete Bosch 0 445 … number and the vehicle/VIN, engine, drive, mounting and metering valve. Similar CP3 family labels do not establish interchangeability. Verify rotation, mounting, drive coupling, inlet, return, electrical control and rail-pressure limits against the part-specific catalogue and installer. BMW identifies Bosch 0 445 010 194 as the CP3 16/3 pump for the US M57TU2 TOP, without establishing that all markets or engines have the same pump. BMW engineering information.

R70 identification and examples

R70 identifies a group within Bosch CP3 pump type designations, not a complete order number or an engine-wide specification. The Bosch CP3 training list records 0 445 010 045 as CR/CP3S3/R70/20-789S for BMW, and 0 445 010 126 as CR/CP3S3/R70/20-89S for BMW. Differences in the complete suffix and associated parts matter. Verify the particular vehicle and supersession using Bosch or BMW data. Bosch CP3 training, parts list.

The US M57TU2 TOP engineering record lists 0 445 010 194 as CP3 16/3; it does not itself label that unit R70. Do not infer an R70 or R90 designation from a model badge or this engineering number without a part-specific cross-reference. BMW engineering information.

Upgrade choices

A healthy R70 may be retained if measured pressure and supply meet the intended calibration. If evidence shows insufficient delivery, a suitable R90, a specialist-modified pump or a dual-CP3 system may be considered. Compare bench flow at the same test pressure and shaft speed, not just a quoted percentage. Verify the fittings, drive and metering-control compatibility; a larger pump is not automatically a bolt-on swap.

The Whitbread 2009–11 US 335d kit describes a second R70 or R90 with its own controller and drive. This is evidence for that kit's stated application, not every 535d or X5. See the R90 page and CP3 family guide.

Diagnosis and installation

Log requested and actual rail pressure under repeatable load and look at associated fuel-metering and rail-pressure faults. Before condemning a pump, check low-pressure supply and filter, air entry, restrictions, electrical supply and metering control, injector return leakage and rail pressure-control components. A fall in rail pressure is a system symptom, not proof of a failed pump.

Common-rail fuel can remain at very high pressure after shutdown. Use the vehicle-specific depressurisation and clean-work procedures, approved high-pressure lines and specified tightening/replacement instructions. Never loosen a live high-pressure connection to find a leak or use hands to check for leaks. After a pump failure, assess contamination throughout the fuel system and follow the manufacturer's repair and cleaning plan.

See fuelling faults, common-rail supply pumps and the M57 twin-turbo guide.