Tuning Wiki

Weber fixed-choke carburettors span horizontal individual-runner sidedrafts, vertical individual-runner downdrafts, compact transverse twin-chokes, and progressive or synchronous street replacement barrels. Although all Weber jets and chokes use metric sizing (in millimetres or hundredths of a millimetre), float mechanisms, idle circuits, jet part numbers and speed-screw limits differ markedly from one family to another.

Weber 45 DCOE 9 idle mixture screw locations, simplified top view
Example: idle mixture screws on a Weber 45 DCOE 9. Original simplified redraw for Tuning Wiki, CC BY 4.0, from the public-domain photograph by Reforma.imufomot; control identification checked against Redline’s DCOE diagram. Other models differ.
Side-by-side comparison of Weber and Mikuni Solex carburettors and a TWM throttle body
Comparison of Weber DCO, 45 DCOE and 48 IDA carburettors with a Mikuni Solex 50 PHH and TWM throttle body. The source's filename and description differ on the DCO size. Photo: Reforma.imufomot, Wikimedia Commons, Public domain.

Finding the adjustment screws

Diagram links are included in each family guide: DCOE, IDF, IDA and IDA 3C, DGV and related models, DGAS and DGES, and DCNF, ICT and ICH. Use a drawing for the exact variant where possible: screws, choke mechanisms and linkage can differ.

Weber carburettor family guides

Weber familyOrientation & stagingMain jet / emulsion familyKey tuning difference
DCOE & DCO/SP (38/40/42/45/48 DCOE; 48/50/55 DCO/SP)Horizontal sidedraft, synchronous twin-choke41110.001 main; F11/F15/F9/F16/F2/F7 tubesChoke size = barrel / 1.25; F8/F9/F6 idle air bleeds cure 2,500–3,000 rpm stumble; 25 ± 1 mm optical well depth.
IDF (36/40/44/48 IDF)Vertical downdraft, synchronous twin-choke41110.001 main; F11 / F2 / F7 tubesShares DCOE jetting logic in a downdraft body; single centermount requires F7 tubes, 000 pump bypass and 2 mm butterfly holes vs dual pairs.
IDA & IDA 3C (48 IDA 2-bbl; 40/46 IDA 3C 3-bbl)Vertical downdraft, synchronous 2-bbl or 3-bbl41110.001 main; F7/F24/F26 tubes; F10 idle (48 IDA)Body-retained float measured with 98014.200 gauge (5.5–6.0 mm on 48 IDA, 12.5–13 mm on 3-bbl); 48 IDA uses bleedless F10 idle jets.
DGV, DGAV, DGEV & DFV (32/32, 32/36)Downdraft progressive 2-barrel41120.001 main; 61440 (F50/F6) tubesIdles on primary barrel only; progressive speed screw limit up to 1½ turns; convertible to synchronous via Webcon MT0098L Sync Link.
DGAS, DGES & DGMS (34 / 38 DGAS)Downdraft synchronous 2-barrel (geared shafts)41120.001 main; 61440 (F50) tubesBoth barrels open together with dual mixture screws; speed screw strictly ≤ ½ turn; preferred over 32/36 on V6/I6 & modified engines.
DCNF, ICT & ICH (36–44 DCNF; 34 ICT; 34 ICH)Compact downdraft twin (DCNF) & single-barrel (ICT/ICH)DCNF 41115.003 (F24/F25/F36); ICT F78; ICH F6DCNF uses cross-axis float bowl and its own 41115.003 main jet; 34 ICT is choke-less dual VW single; 34 ICH is manual-choke single OEM swap.

Shared Weber tuning rules

  • Mechanical baseline first: verify compression, valve clearances, ignition advance (12–16° idle advance on modified DCOE/IDF builds), zero manifold air leaks, and free throttle-linkage return before turning mixture screws.
  • Fuel pressure ceiling: Weber needle valves are sensitive to excess pump pressure; keep pressure regulated around 2.5–3 psi on DGV, DGAS, IDF, DCOE, ICT and ICH (and ~3.5–4.0 psi max on large-bore 48 IDA builds).
  • Do not force mixture screws: turning tapered brass screws hard into the alloy body damages the seat permanently; always seat lightly by finger feel before backing out to baseline turns.
  • Cold-start priming on choke-less carbs (48 IDA / 34 ICT / unchoked DCOE): allow electric pumps to fill the bowls (5–10 s), give 3–4 full strokes of the accelerator pump, and crank on light throttle rather than flooding with an unused starting circuit (Dave Andrews DCOE guide).

Related pages

Sources