When tuning a supercharged 3.0 TFSI, a fuel-pressure shortfall or a bank-specific mixture deviation needs investigation before more load is requested. This guide uses Audi's CAJA engine description and product-specific Simos 8.4/8.5 references to frame a log review. Audi SSP 437 identifies the CAJA's management as Simos 8 without specifying the suffix; its fuel-system description is an engine example, not proof that every 8.4 or 8.5 vehicle has identical components or channels.
Low and high pressure are separate observations
Audi describes a demand-controlled system on the CAJA with an in-tank fuel pump G6 and pump controller J538, a mechanically driven high-pressure pump with fuel-metering valve N290, low-pressure sender G410 and high-pressure sender G247. The high-pressure side supplies the six direct injectors. The ECU also receives an upstream oxygen-sensor signal for each bank. Identify the sensors and channels on the vehicle under test before applying this layout to it.
The high-pressure reading alone cannot identify why pressure differs from request. If available, record requested and actual high-side pressure together with low-side pressure, engine speed and load. A low supply pressure at the same time suggests checking the supply side; a healthy-looking supply signal with a high-side error calls for further checks of the high-pressure circuit, metering and sensor signal. Neither pattern proves a particular part has failed. Use current vehicle-specific guided diagnosis before disturbing the fuel system.
Two Audi hot-condition fuel-pressure examples
Audi bulletin 01 13 68, 2032900/1 describes P008700 for 2013 A6/A7 3.0 FSI vehicles. It says an incorrect software setting could misinterpret data under conditions such as long idling or heavy stop-start traffic, and identifies coolant temperature above 100 °C in the freeze frame for the described condition. Its software table lists a specific 4G0907551D version change. The bulletin does not establish an ECU suffix, and its historical software remedy does not make every P0087 a false fault. Check the exact vehicle, software, freeze frame, current repair information and measured pressure before drawing a conclusion. An ECU update may replace a modified calibration; identify and preserve its read where supported, confirm file scope and discuss the consequences before service.
A separate Audi bulletin 20 16 76, 2043758/4 covers specified 2012–2016 A4, A5, A5 Cabriolet, A6, A7 and Q5 with 2.0 or 3.0 engines. For its hard-start and low-pressure P310B example it describes hot ambient conditions, long idle periods and fuel vapour; symptom code 6183 is associated with the 3.0 TFSI example. Its procedure checks low-side pressure, delivery rate and fuel lines before deciding whether the delivery unit is at fault. It does not identify a Simos suffix or establish that every low-side fault is caused by vapour. This is an older bulletin and later revisions may differ; follow the current vehicle-specific procedure.
These examples distinguish a high-side fault indication with a documented software interpretation issue from a low-side pressure fault in a separate set of conditions. Record ECU software, temperatures, fault and symptom codes, freeze frame and operating state; compare actual signals and test the fuel supply. Neither bulletin supports suppressing a fault monitor, automatically replacing a pump, or assuming that a normal idle reading proves adequate fuel delivery at high load.
Build a useful baseline
- Record engine code, ECU hardware and software, fuel, pulley and pump hardware, calibration and any fault codes. Verify whether the installed tune is intended for that fuel and hardware; do not assume a performance label describes a standard configuration.
- Where supported, log high- and low-pressure fuel measurements, requested rail pressure, lambda target and actual for both banks, short- and long-term fuel trims, engine speed, throttle, air charge or boost and intake temperature. Include ignition timing and per-cylinder knock correction where available. Confirm units, channel identity and sample rate: an ECU-reported target is not a physical measurement.
- Compare repeat runs at similar engine speed, load and temperatures. Note whether pressure error begins during a transient or persists, and whether both banks deviate together. A one-bank difference deserves a different investigation from a common-mode supply issue, but neither pattern alone diagnoses an injector, sensor or pump.
- If pressure or lambda does not track as expected, stop increasing load and investigate the relevant fuel supply, control, sensing, intake and ignition systems using the current service procedure. Confirm the result after repair before assessing the calibration.
APR's VCDS logging reference lists long-term fuel trims for banks 1 and 2 and individual-cylinder timing-retard values in its Simos 8.4 example. Its numbered rail-pressure example is in a separate MED9 section: those block numbers should not be transferred to Simos 8.4 or 8.5. Logger channels and scaling must be verified for the exact ECU and software.
Definition lead: lambda and catalyst-heating maps
A publicly indexed A2L file identifies its own project as Simos 8.5 structure L10 with EPK S85L100. It describes two ip_lamb_bas maps as basic lambda setpoints, with axes referencing engine speed and maf; in that definition, maf is described as predicted air mass for basic fuel injection, not necessarily a hot-film sensor reading. It also labels separate basic lambda maps for catalyst heating at idle and in other operation, including variants described for multiple injection. Their listed inputs include engine speed and a limited slow-path torque request.
The same definition labels a fuel-pressure setpoint map for catalyst heating and another for catalyst heating with multiple injection. These descriptions show that operating mode can matter when investigating a target; they do not establish which map the ECU uses, the actual values in a particular binary, or how the control selects among them. The file’s origin, rights, completeness and match to any vehicle are unverified. Confirm the actual ECU, software and definition and use supported, correctly defined logs before interpreting a transition or changing a map. See Simos 8.5 for the file’s identification and limitations.
Hardware and fuel changes
Integrated Engineering markets a 3.0T pump upgrade for specified supercharged applications and discusses it in the context of dual-pulley and higher-octane builds. This is one supplier's product scope and claim, not proof that a pump upgrade fixes every low-pressure, injector, sensor or calibration problem. Follow the supplier's current vehicle and tune requirements; assess pressure and mixture across the relevant operating range after a hardware change.
APR's Simos 8.5 ECU upgrade page specifies different octane calibrations and notes that availability depends on box code and revision. RON and AKI are different ratings; use the fuel and blend specified for the actual calibration. An ethanol blend or a higher-flow pump does not establish that a particular ECU is flex-fuel calibrated, and a single pressure reading does not establish adequate injection capacity.
Worked example: fuel blend and pump requirements
Integrated Engineering's 3.0T dual-pulley manual-transmission package offers a specific E40 calibration and says its package requires a heat exchanger; for E40 it also requires a high-pressure fuel-pump upgrade. The supplier says its described factory fuel system cannot support full E85 safely with the pump upgrade alone. These statements concern its specified hardware, fuel and calibration, not an independently tested limit for all 3.0T builds. The product listing does not identify an ECU suffix. Confirm the installed ECU and current supplier requirements for the actual setup.
The supplier's example uses approximately two parts E85 and three parts E10 petrol. If those labels represented exactly 85% and 10% ethanol by volume, the blended fraction would be (0.4 × 85%) + (0.6 × 10%) = 40%. This arithmetic assumes those actual component contents and volumes, an empty starting tank and complete mixing. Fuel composition and remaining fuel can differ; measure the blend and include the fuel already in the tank rather than assuming a pump label or volume ratio proves the result. Use only fuel and hardware covered by the actual calibration.
IE's separate 3.0T tune listing also specifies permitted pulley combinations and excludes its described CREC application from that software suite. A stronger pump or a matching-looking pulley does not by itself establish file compatibility or adequate delivery. Compare requested and actual rail pressure, low-side supply where supported, and lambda under repeatable conditions; investigate a mismatch before increasing demand.
Ethanol blends and the stoichiometric constant
Community discussion of Simos 8.4 tuning centres on a definition label c_mff_fac, described as a reciprocal stoichiometric air/fuel-ratio constant. A single fixed constant, even where correctly identified, does not establish automatic ethanol measurement, flex-fuel blending, suitable lambda targets or sufficient injector and pump capacity. No independently validated universal value or address has been published; match the exact software and verify the complete fuel strategy and hardware for the measured blend.
One owner report from that discussion describes a high-ethanol fault occurring during steady cruising, while full-load pulls had not shown the same issue. It records a change in rail pressure and proposes an injection-window limitation in a particular operating mode, while stating that the cause was not verified. The observation is a reason to log the intended operating range, including warm-up, light-load cruising, transients and full load, not evidence that increasing pressure is the correct remedy. Compare lambda target and feedback, pressure request and actual, supply pressure and reliably defined injection information with the same fuel and conditions; investigate faults and the fuel system before attributing a mismatch to one map.
Sources
- Audi SSP 437: 3.0-litre V6 TFSI engine with Roots blower, pages 46–50. CAJA fuel system, sensor and injection description; Simos 8 family without suffix. Accessed 17 November 2026.
- APR VCDS logging reference. Simos 8.4 and separate MED9 logging examples. Accessed 17 November 2026.
- Integrated Engineering 3.0T high-pressure fuel pump upgrade. Supplier's intended applications and hardware context. Accessed 17 November 2026.
- APR ECU upgrade: 3.0T EA837 Simos 8.5. Product-specific octane, box-code and calibration coverage. Accessed 17 November 2026.
- Nefarious Motorsports Simos 8.4 tuning discussion, replies 121–124. Owner and community report, not validated. Direct forum access was unavailable; the text was reviewed through indexed copies.