Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

On a supercharged 3.0 TFSI with Simos 8.4, charge pressure, bypass position and ignition correction can help distinguish a calibration request from a fault or a physical limitation. APR publishes a VCDS channel list for its Simos 8.4 example. Audi's Self-Study Programme 437 describes the air system on a 2009 A6 CAJA engine, identifying the ECU only as Simos 8. The Audi component descriptions below are useful system context, not proof that all 8.4 vehicles have identical hardware, fallback behaviour or diagnostic channels.

Choose channels for the actual ECU

APR's VCDS logging guide explicitly lists the following general measuring values under its 3.0 TFSI Simos 8.4 heading:

  • 22 throttle position; 24 accelerator position; 35 engine speed.
  • 33 and 34 long-term fuel trim for banks 1 and 2; 128 ambient pressure.
  • 292–297 ignition timing retard for cylinders 1–6; 298 ignition angle.
  • 421 mass air flow; 436 boost pressure, described as absolute; 632 intake-air temperature; 702 boost control valve angle.

These are APR's example labels and numbers, not a guarantee of a matching channel on every software revision, diagnostic tool or vehicle. Verify each channel's label, units, reference and availability on the connected ECU. The same APR page also shows numbered groups for a different MED9 engine: do not transfer those group numbers or N75 duty to Simos 8.4 as if they were the same list. The source does not establish whether channel 436 is each bank's actual sensor, a selected value or a calculated value, nor the sign convention for channel 702. Verify those details before interpreting the trace.

APR notes that grouping measurements can improve logging rate. Use a focused set with RPM, pedal and operating conditions to preserve context; use separate comparable logs for additional detail if necessary. Record the file identification, fuel, pulley and hardware, gearbox, temperatures, fault codes and test conditions. A dyno or other controlled, lawful setting is appropriate for load testing.

Understand the bypass

In Audi's SSP 437 CAJA example, the belt-driven Roots supercharger circulates air through an electrically operated bypass. During the documented part-load operation the bypass is open and the throttle manages load; in charge-pressure operation the bypass regulates load with the throttle open. An open bypass at idle or light load is therefore not, by itself, proof of a fault. Valve-angle units and open/closed direction depend on the channel definition.

The documented J808 control-flap unit contains the V380 motor and G584 position feedback. Audi says the feedback also contributes to adaptation. For loss of the feedback signal in this example, the flap is de-energised and spring-opens for the driving cycle, with reduced available output and a fault indication. Treat this as a documented failure response to investigate, not a diagnosis based on low boost alone; use the appropriate workshop test plan and never assume that a logged angle proves mechanical movement.

The reproduced Audi A4 Mk3 3.0 TFSI workshop procedure for J808 calls for guided adaptation after renewing that control unit. This requirement is specific to the described replacement procedure; check current repair information and the actual ECU and component before service. An adaptation command is not proof of a mechanical repair or a substitute for investigating a fault.

Compare pressure readings in context

SSP 437 places G71/G42 upstream of the throttle and G31/G72 and G447/G430 downstream of the charge coolers at the two cylinder banks. It describes G71 as an input to bypass positioning and the two bank-pressure signals as inputs to charge control and calculated air mass. The correct pressure comparison therefore depends on sensor location, throttle position and operating state. Distinguish absolute pressure, gauge pressure and ambient pressure; a pressure difference across a throttle or supercharger is not automatically a leak.

When readings appear implausible or disagree with the engine's behaviour, verify which physical sensor or model each channel represents, its reference and units, then investigate wiring, supply, sensor faults and air-path leaks using the applicable repair procedure. Audi describes sensor substitution or backup behaviour after a detected plausibility fault, so a normal-looking displayed value does not by itself clear the original sender. Compare fault memory and supporting measurements before changing a sensor scaling or load map.

Interpreting an air-mass channel and intake flaps

APR calls channel 421 “Mass Air Flow” in its Simos 8.4 list. The name alone does not prove a hot-film MAF sensor is fitted or that this particular displayed value is a direct sensor measurement. For the CAJA/CCAA engine in Audi's English-language self-study programme 925803, the two downstream bank pressure signals contribute to a calculated air mass used by torque-based engine management. The source identifies the family as Simos 8 but does not establish the exact suffix or the derivation of APR channel 421 on each vehicle. Confirm the ECU channel definition, units and installed sensors before diagnosing a MAF or altering an air-mass map from that label.

On the same documented engine, intake manifold flaps are separate from the supercharger bypass. Audi describes vacuum-operated runner flaps supplied through valve N316 and monitored by position sensors G336 and G512. It states that loss of N316 actuation or a faulty valve can leave the power port closed and reduce output. This gives a possible investigation when output is poor, not proof of the cause in a particular log: check supported position information, fault memory, vacuum supply, actuator and mechanical movement using the correct vehicle-specific test before changing air or torque maps. A position sensor's signal is feedback and diagnosis, not an independent direct measurement of cylinder airflow. Audi SSP 925803, pages 24–29.

In Audi of America bulletin 2033919/8, the listed 2013 A6, A7, S4, S5, S5 Cabriolet, Q7 and Q5 with 3.0 FSI may have P2006 or P2007 for a runner flap stuck closed, sometimes with a slight reduction in high-rpm power. The bulletin distinguishes vacuum-supply leaks from defective runner actuators and checks the supply before its specified repair. This is a model- and condition-specific example, not proof that a particular fault or reduced output has that cause or that the bulletin identifies the Simos suffix. Check current vehicle-specific service information and complete the relevant diagnostic tests; avoid replacing parts solely from a code or altering airflow calibration to mask a mechanical problem.

Charge cooling and repeated-run changes

On the SSP's CAJA engine, two water-cooled charge coolers share a lower-temperature circuit with electric pump V188. The circuit is interconnected with the main cooling system at the expansion tank. The ECU requests pump operation according to operating conditions, and the pump provides feedback. Audi describes fault memory entries and possible output reduction if excessive charge temperature is detected; the example also notes that a pump failure need not illuminate a warning lamp. This is not proof that every 8.4 vehicle will react identically.

If performance falls on repeated runs as intake temperature rises, compare the temperature trace and operating conditions and investigate charge-cooling flow, coolant condition and the relevant pump diagnostics. Heat, fuel quality, ignition correction and other factors can also change the result. A pump that is stopped under one condition is not automatically faulty; follow the vehicle-specific diagnostic procedure, including any guided actuator test, and do not run a centrifugal pump dry.

From log to calibration decision

  1. Read fault codes and check baseline mechanical, air, fuel, ignition and cooling condition before changing a calibration.
  2. Compare requested and actual pressure, pedal, throttle and bypass information where accurately defined. Interpret the signals together with RPM and operating mode; a target is not proof of achieved pressure.
  3. Review individual-cylinder timing corrections, ignition and temperatures at comparable conditions. A correction channel is an ECU response, not a direct measurement of knock severity or a universal safe limit.
  4. If a discrepancy persists, identify whether the request, actuator, sensor, airflow, fuel or a protection is involved before changing a limit. Confirm the exact definition and map function for the loaded software.

Sources