Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

Scope. Temperature signals are used by air-charge estimation, ignition and fuelling; they are not interchangeable just because a logger calls them IAT. The engineering identifiers and axes below are examples from the community SC8S5031_C_OEM Simos 18.1 reference, not a promise that another Simos 18 software version contains the same maps or uses the same selection. Verify ECU hardware and software, matching definitions, array indices, units and channel sources for the individual vehicle.

Measured temperature and modelled charge temperature

The reference lists tig_im_mes as measured intake-manifold gas temperature, while tig_thr and tig_inv refer to gas temperatures at the throttle and intake valve. It also identifies tig_ico_down as the temperature downstream of the intercooler; do not infer a dedicated sensor or a particular physical location without checking the configuration. Ambient taa is another signal, not necessarily a direct measurement. The AIRT acquisition reference and customer adaptation reference describe these identifiers.

COBB's MQB monitor list calls its Charge Air Temperature channel modelled and lists IAT and Ambient Air Temp. separately. These are product-specific monitor descriptions: confirm each channel's source, units, filtering and availability before comparing values between tools. A modelled charge temperature does not establish that a temperature sensor exists at that model's location. COBB MQB monitor descriptions.

Throttle and intake-valve model examples

  • ip_tig_thr_mdl_ofs_1 is a throttle gas-temperature model offset in °C against engine speed and gas mass m_gas_tig_im_airt in mg/stroke.
  • ip_tig_thr_mdl_ofs_2 is a throttle-temperature model offset in °C against vehicle speed in km/h and rate_heat_im; the extracted definition does not establish a physical unit for the latter.
  • ip_crlc_tig_thr_mdl is a throttle-temperature model filtering factor. Its temperature-difference axis is marked NO_INPUT_QUANTITY in the reference; the exact runtime input should be confirmed. Separate after-start and engine-stop filtering constants are listed.
  • ip_tig_inv_mdl_ofs_2 is an intake-valve model offset in °C against vehicle speed and rate_heat_im. ip_crlc_tig_inv_mdl is an intake-valve model filter factor.
  • ip_tig_inv_vlft_1[2][2] and ip_tig_inv_vlft_stnd[2][2] are valve-lift-related intake-valve temperature offsets in °C. Their main axes are engine speed and model gas mass in mg/stroke; intake and exhaust cam position breakpoints are additionally used for four-dimensional interpolation. Verify the lift case, array selection and software.

These are model calibrations, not a raw temperature-sensor voltage conversion. AIRT throttle model; AIRT intake-valve model.

Air charge and temperature corrections

The INSY temperature-correction reference lists ip_eff_tia_im_fac as an intake-manifold-temperature-related volumetric-efficiency weighting factor, against engine speed and predicted cylinder air mass in mg/stroke. ip_eff_vol_tia_cyl_stnd is a reference cylinder temperature in °C against engine speed and predicted cylinder air mass; ip_eff_tco_fac is a separate coolant-related weighting factor. These are contributions to a model, not direct measurements of intercooler efficiency.

The IGSP temperature-correction reference lists ip_iga_bas_temp_n_32 as a basic ignition temperature correction, in crank-angle degrees against engine speed and selected temperature tia_iga_cor_sel_cbk[0]. Positive and negative correction weighting maps also exist. Other inputs and corrections affect delivered timing: log final ignition and per-cylinder knock correction rather than assuming the table output is the final angle.

The TQDR full-load enrichment reference identifies ip_lamb_fl_sp and ip_lamb_fl_sp_tia as normal and temperature-related lambda maps against RPM and elapsed full-load time. Temperature selects the relevant branch; it is not one of those map axes. c_tia_thd_lamb_fl_sp and c_tia_hys_lamb_fl_sp are threshold and hysteresis examples. EcuTek's EA888 RaceROM guide describes product-specific full-load lambda maps and notes RaceROM can replace the OEM maps; verify which logic is active in the file.

Sensor calibration and practical checks

Acquisition example: the SC8S5031 AIRT acquisition reference labels ip_tlts_air_mes[0] a sensor-voltage-to-air-temperature conversion curve with °C output. Its axis is voltage-labelled but marked NO_INPUT_QUANTITY; the displayed function equation uses indexed vp_lts_air as input to tlts_air_mes. Its copied table caption calls the input a digital PWM signal, so confirm the target's signal interface and actual computation. The same description shows an intake-manifold index feeding tig_im_mes, but it does not establish that array element [0] always means the manifold sensor. The numeric map range is a data representation, not the replacement sensor's physical operating range or a universal calibration.

vp_lts_air[0] and tlts_air_mes[0] are voltage and converted-temperature runtime signals in this extraction. The manual-value selection lc_tlts_air_mes_as[0] and c_tlts_air_mes_as[0] can select a calibration-provided value in the documented calculation, so even a field described as measured must be interpreted in its active branch. Confirm sensor index, wiring, transfer curve, fallback and software with the matched A2L and implementation; do not copy a temperature curve or rely on a plausible display to prove the sensor is functioning. AIRT acquisition.

Audi SSP 920243, printed pages 49–51, depicts G42 intake-air temperature with G71 manifold pressure on its illustrated EA888 Gen3 engines; this does not establish every vehicle's wiring, ECU channel or replacement sensor's temperature characteristic. A combined pressure/temperature replacement can have a suitable pressure range and still require its temperature element and interpretation to be checked independently.

Temperature sensor diagnostics in SC8S5031

The AIRT sensor-diagnosis reference lists c_vp_lts_air_oc[0] and c_vp_lts_air_scg[0] as voltage thresholds for separate electrical diagnostic paths, and c_tlts_air_orng_h[1] / c_tlts_air_orng_l[1] as temperature out-of-range thresholds. lv_cdn_lts_air_oc[0] and lv_cdn_lts_air_scg[0] indicate conditions for those diagnostics; lf_state_dgo_lts_air_oc[0] and lf_state_dgo_lts_air_scg[0] are diagnostic states. Their array indices, enabling conditions and state meanings must be checked on the target. Threshold names and representable limits are not vehicle-specific test specifications, and an inactive monitor is not proof of a healthy circuit.

For plausibility rather than an electrical-open/short test, the AIRT plausibility reference identifies c_temp_dif_tlts_air_plaus[0] as a measured-versus-modelled temperature difference threshold; tlts_air_plaus_mes[0] and tlts_air_plaus_mdl[0] are the compared runtime values, not two independently measured sensors. Its stability and symptom counters require the relevant recurrence to convert to elapsed time. Separately, the intake-gas plausibility reference has c_t_es_min_stuck_tig_plaus in minutes, c_t_ast_min_stuck_tig_plaus in seconds and c_dist_min_stuck_tig_plaus in metres for the stuck-signal check. lv_cdn_stuck_tig_plaus[0] is a runtime condition. A short stationary warm-up may not meet these conditions; no flag in that period does not establish a passed test. Preserve the diagnostic paths and investigate the actual sensor before altering calibration.

Compare relevant measured temperatures with a suitable reference after a cold soak and at controlled warm conditions; account for sensor position, response lag and heat soak. Log ambient temperature, available IAT and modelled charge-temperature channels, engine speed, manifold and upstream-throttle pressure, requested and actual lambda, final ignition, individual cylinder knock correction and active torque limits. Resolve sensor and cooling faults first. For intercooler comparisons record probe positions, vehicle speed, ambient conditions, load, heat soak and repeatability; an isolated modelled value cannot measure intercooler effectiveness.

See also Simos 18 air charge modelling, bigger turbo tuning, and turbocharger protection.

For coolant valve control, fan demand and afterrun, see Simos 18 cooling and thermal management.

For practical sensor placement, pressure-drop and heat-soak comparisons, see Simos 18 intercooler and charge-air cooling upgrades.

COBB ignition-correction source selection

For its documented MQB calibration, COBB’s tuning guide describes “Switch for Charge Air Source” selecting the input to its “Final Ignition Angle Correction IAT/CAT” table: 0 selects IAT at the T-MAP sensor and 1 selects modelled charge-air temperature in the example. Those values and display names are specific to the described COBB definition. Check the active bit, channel source and software before comparing correction with a logged temperature; this does not mean every Simos 18 calibration exposes the same switch.