The same job, several makers
The car maker specifies the range, the plug and the place in the intake. The sensor maker builds the element. A Bosch 20 to 250 kPa sensor and a Denso sensor with the same three pins are not the same curve. This page is which maker used which kind of sensor. Curves and pins for a particular part stay on that part’s page.
| Maker | What they publish | Where it turns up |
|---|---|---|
| Bosch | Absolute, ratiometric, often with an NTC. Curve 1 or curve 2, and a pin order that changes with the housing. | European petrol and diesel, and many GM, Ford and Asian installations supplied by Bosch |
| Bosch Motorsport | The same element, with a printed sensitivity and offset in V/bar. | Air-box and charge-pressure parts sold for calibration and logging |
| Denso | Piezoresistive MAP and T-MAP. The aftermarket catalogue does not print a voltage curve. | Toyota, Lexus, Honda, Mazda, Subaru, Suzuki, and other engines Denso supplied |
| Siemens VDO, later Continental | MAP and T-MAP. One catalogue range for the turbo sensor is 500 to 3000 hPa. No voltage curve is printed against the part numbers below. | Volkswagen Group, Renault, Ford, Audi |
| Ford | EEC-IV MAP and BARO sensors output a frequency. Later Ford engines also use analogue sensors from outside suppliers. | EEC-IV speed-density, and a separate barometric sensor on some vane-air engines |
| NXP, earlier Freescale and Motorola | The MPX silicon element, with a published transfer function. This is a component, not a vehicle part. | Inside sensors, inside some control units, and used loose on aftermarket controllers |
| Delphi, earlier Delco | The GM 1-bar, 2-bar and 3-bar parts. The part number selects the range. | GM speed-density and the factory boosted engines |
Bosch
Bosch is the maker whose ranges are printed as a catalogue. Thick-film sensors, micromechanical sensors with and without a temperature element, a moulded-cable boost sensor, and the bare cells used inside a device are on Bosch absolute-pressure sensors. Part numbers in the 0 261 230, 0 281 002 and 0 273 300 ranges are those parts. A neighbouring number is a different range, and on several of them the pin order changes too.
The motorsport air sensors are a separate list. PS-AA, PS-AL, PS-AS, PSP and the PST combined sensors each have a sensitivity and an offset, and they do not share one plug. Those figures are on Bosch Motorsport air-pressure sensors. A PST-F in that same catalogue is a fluid sensor, up to hundreds of bar. It is not an air-box sensor.
Denso
Denso’s engine-management catalogue describes the MAP sensor as a semiconductor vacuum sensor using the change in resistance of a silicon crystal under pressure. The signal is a voltage into the control unit. The same text allows the part to be used as a boost sensor upstream of the throttle, or as a turbo-manifold pressure sensor, and a T-MAP adds air temperature in the same housing.
The construction in that catalogue is a sensor chip and a circuit chip, wire-bonded, covered by gel and rubber, in a resin case with the pressure port moulded in. Denso’s stated reason for the two-layer cover is the mixture of fuel, oil and moisture in the manifold. The catalogue’s own failure notes follow from that: liquid or sustained humidity in the port, a leaking manifold or vacuum hose, and an open or short in the wiring. The fault codes it names for this sensor are P0105 to P0109.
That catalogue does not print a volts-against-pressure table. Service parts are numbered DAP, and the installation torque depends on which DAP number is in the box.
| Denso service part | Torque |
|---|---|
| DAP0101, DAP0102, DAP0108, DAP0109, DAP0110, DAP0111 | 4.0 to 6.0 Nm |
| DAP0105, DAP0106, DAP0107 | 2.8 to 4.1 Nm |
| DAP0103, DAP0104 | 1.6 to 2.4 Nm |
The application tables in the same catalogue use a hyphenated form, DAP-0110 and so on. Match the number on the part. A torque from the wrong row, and a curve from a different maker, are both the wrong data for that sensor.
Siemens VDO
Siemens VDO’s engine-management sensor catalogue separates a MAP, which measures manifold pressure after the throttle, from a MAP used on a turbocharged engine to measure pressure after the turbocharger. The range it prints for that turbo sensor is 500 to 3000 hPa, which is 50 to 300 kPa. A T-MAP in the same description adds a temperature element.
The part numbers in that catalogue are identification and a pin count, not a curve. No volts-per-kilopascal figure is printed against them.
| Part | Pins | Catalogue applications |
|---|---|---|
| 5WK96812Z | 3 | Ford Fiesta, Focus II, Ka, StreetKa |
| 5WK9681Z | 3 | Audi A6 (4B), Ford Fusion, and a long Renault list from Clio II through Trafic II |
| 5WK9693Z | 4 | Audi A2 and A4 (B6), and the Seat, Škoda and Volkswagen cars of that generation in the same list |
A four-pin plug is consistent with a pressure element plus a temperature element, and the catalogue does describe a T-MAP. The line for 5WK9693Z itself only says pressure sensor. Treat the fourth pin as temperature only when the drawing for that part says so.
Ford, GM and the silicon element
Ford’s EEC-IV speed-density system uses a piezoelectric disc that changes frequency, not voltage. Frequency rises as manifold vacuum falls. At atmospheric pressure, on the 30.0 in-Hg barometer the pinpoint test is written against, the output is 159 Hz. The vacuum table, the key-on barometer table and the test-pin colours are on Ford MAP and BARO frequency sensors. A later Ford analogue sensor is a different part. The Siemens 5WK96812Z above is one of those, and it is not read in hertz.
GM’s speed-density and factory-boosted engines use Delphi sensors in 1-bar, 2-bar and 3-bar ranges. The part number is the range. A linear value and an offset taken from a tuning package belong to one part number and to the way that control unit scales its analogue input. They are not a family constant, and they are not published here without the Delphi sheet for that part.
Under many of these housings, and on aftermarket controllers used without a vehicle housing, the element is an NXP MPX device. MPX4115, MPX4250 and MPXH6400 each have a transfer function in the device datasheet. Those functions are on NXP MPX absolute pressure sensors. A sensor whose label is Bosch, Denso or Delphi is not measured with an MPX equation unless that sensor was built on that die and the housing calibration is the die calibration.