Tuning Wiki

Dynostar manufactures chassis dynamometers and associated data acquisition and control equipment. Its DAS electronics and Advanced Dyno Station software are supplied with Dynostar dynos, and the company advertises an A801 retrofit package for roller chassis installations. The mechanical dyno, retarder, power supply, sensors and control software must be specified as a complete system.

Dynostar DAS A801 upgrade kit including electronic control equipment, load cell, brackets, sensors and cables.
Dynostar DAS A801 upgrade-kit image. The supplier says the pictured contents may differ from the product supplied. Image: Dynostar, used with permission.

DAS and Advanced Dyno Station

Dynostar says its rolling-road chassis dynos use its DAS data-acquisition system. A junction box collects supported sensor signals such as boost, throttle position, temperature and air/fuel ratio. The Advanced Dyno Station PC software presents measurement screens, a run database and graphs. It displays and compares power and sensor traces using configured vehicle and test settings; the sensors, modules and licences included depend on the package.

The supplier describes Dynamic, Dynamic A/T, Static and Transient tests. In the stated Static mode the retarder holds selected points; Transient mode adjusts retarder load for a requested test duration. Those modes require a suitable braked dyno and correctly configured hardware, not software alone. Weather corrections, units and graph traces are configurable. Dynostar notes its EV mode requires the EV module; check actual software generation and options. Dynostar software documentation.

Speed-hold feedback loop from target through controller, brake actuator and dyno to measured speed.
General dyno speed-hold feedback loop; hardware and sensor locations depend on the installation. Original schematic for Tuning Wiki, CC BY 4.0.

A801 upgrade kit

The DAS upgrade kit A801 is advertised for refurbishing roller chassis dynos. The listing identifies a DAS unit, junction box, remote, communication and RS232 cables, drum-speed sensor, load cell, eddy-current brake (ECB) power supply, calibration weight and brackets. It also describes facilities for programmed cycles and control of suitable fan, wheelbase and beam equipment. The product is not itself the roller frame or brake.

An ECB supply is a power interface for the brake: match the particular coil's voltage, current and cooling requirements, not just the controller plug. Confirm the roller/sensor layout and whether the existing power supply and wiring can be reused. The supplier calls the kit broadly applicable to roller chassis upgrades, but its listing does not establish compatibility with every named make, hydraulic valve or hub dyno. Discuss a specific installation before purchasing.

Other units and options

The Dynostar electronics catalogue separately lists Mini DAS A802, DAS Integrated A803 and an EV kit, alongside temperature and lambda modules. The catalogue listing alone does not establish that these alternatives have A801's full contents or supported layouts; obtain each kit's own specification.

For an example of manufacturer-supplied equipment, the Dynostar 2C product page lists integrated DAS, Advanced Dyno Station and a remote, while the 4T page identifies an eddy-current brake and the same software family. These are distinct dynos with their own capabilities and operating envelopes.

Installation and calibration

Record roller diameter and inertia, speed-sensor pulses, load-cell range, brake-supply rating, operating modes and correction standard. Verify sensor calibration, emergency-stop and actuator behaviour using the maker's procedures. A controller upgrade does not increase the retarder or roller's mechanical or thermal capacity. Product details are based on the cited manufacturer listings; verify current version and support.

Related: Dynamometer control systems · Factory and aftermarket controller comparison · Dyno measurement.

Examples of complete Dynostar dynamometers

A motorcycle on a Dynostar D50-series dynamometer
The D50 motorcycle dynamometer series. Image: Dynostar, used with permission. Follow the manufacturer's actual setup instructions.

The D50i is an inertia-based two-wheeler machine; the D50ECB adds a 400 N·m eddy-current brake and the product page lists MiniDAS and Advanced Dyno Station. The D70 and D70Ti combine a high-inertia drum and an air-cooled eddy-current brake; the Ti has adjustable drum inertia. The compact 2C suits light two-wheelers and distinguishes 62.8 kW cold from 14 kW continuous brake power. For cars the Z4 is a linked four-wheel-drive roller system. Each dyno has its own speed, torque and duty limits; confirm the precise machine and brake configuration.

See motorcycle and powersports dynamometers for further examples.