Cleaning removes ash
A regeneration removes soot. Cleaning is the removal of ash, which means the brick has to come out of the exhaust and the packed plugs at the ends of the inlet channels have to be driven back out the way they came in. A fuel additive sold as a cleaner, and a fluid poured in through a pressure-sensor hose, do not reach those plugs. They can loosen soot on the inlet face. The ash that has shortened the channels stays, and so does the pressure that made the car turn up.
Cleaning is worth doing when the brick is intact, the ash mass or the residual pressure says the volume has gone, and the substrate has not melted or cracked. A cordierite brick with a hole melted through a wall, or a silicon carbide brick with a segment loose in its cement, is a replacement. Washing it leaves the hole.
How a workshop clean is done
The can is removed, or the brick is extracted from the can if the construction allows it. The inlet face is inspected. Channels that are glazed, collapsed or shiny have been overheated. Channels that are simply dark are sooted or ashed and can be cleaned. A borescope, or a lamp on the outlet face while the inlet is lit, shows whether the wall still separates the two sets of channels.
Three methods are in use, often in combination.
- Air. Pulses of compressed air are blown from the outlet side toward the inlet, so the ash plug is driven back along the inlet channel and out of the face it entered through. Blowing only from the inlet packs the ash harder against the end plug. The brick is supported. A hammer blow cracks ceramic that the pressure drop had not yet condemned.
- A bake, then air. The brick is heated to burn residual soot so the air pulse is moving ash rather than a wet carbon cake. The temperature has to stay inside what that substrate and its washcoat can stand. A kiln cycle that would be a mild regeneration for silicon carbide can glaze cordierite and sinter the alumina washcoat, after which the filter flows freely and no longer lights soot at the calibrated temperature. The material has to be known before the heater is switched on. See substrates and coatings.
- A wash. Water, sometimes with a detergent the process specifies, is flowed through the walls to carry fine ash out of the pores. The brick is then dried completely before it is refitted. A damp ceramic hit by hot exhaust cracks. A pressure washer in the channels erodes the wall and strips washcoat. Flow and pressure for a wash are the process the cleaning machine was built around, not the maximum a lance will produce.
Weighing the brick before and after is the check that ash left. A filter that loses negligible weight did not need cleaning, or the ash is glazed in place and will not move. A filter that loses a large fraction of its gained weight, and whose residual pressure on a flow rig has returned toward the new-filter line, is the successful case. The rig comparison has to be at a stated flow. A pressure quoted with no flow beside it is not a result.
Refitting
Sensors, hoses and the faces of the flanges are part of the job. A new or cleaned brick with a pressure hose still full of condensate reports the old fault. Clamps and gaskets that leak upstream of the pressure tappings make the control unit see a drop the brick does not have.
The stored loads are then set to match the part that was fitted. On a control unit with a separate ash mass, that mass is reset. Leaving it at the pre-clean value makes the new pressure look like a failed regeneration, and the car is back in a restricted mode with an empty filter. On a soot-only strategy the soot mass is reset and the pressure check is allowed to relearn. Where ash monitoring was switched off in the calibration, there may be no ash figure to reset. The pressure sensor is then the only memory, and a road test at a known load is what shows the baseline has actually fallen. The load model page is the distinction.
The reason the ash accumulated is still there. Low-SAPS oil if that is what the engine was specified with, a turbo or valve-guide oil leak, an over-dosing additive pump, and a car that never finishes a regeneration all fill the cleaned brick again. A clean without that cause is a shorter interval than the first one was.
What is not a clean
- A forced regeneration. It burns soot and stops at the ash line.
- A bottle of cleaner in the fuel tank. It may change a later regeneration. It does not move an ash plug.
- A liquid introduced through the differential-pressure hose. The hose is a sensing passage. Filling it is how the next pressure reading is ruined.
- Running the engine with the filter removed and the can empty. That is not a clean. A missing filter, where one was fitted, is an emissions fault. The legal position is on particulate filter faults.
A cleaned filter is a used filter. Residual ash inside the wall pores, a washcoat that has aged, and any segment joint that was disturbed all stay. The service that follows is shorter than a new brick’s, and the pressure baseline should be recorded so the next diagnosis has something to compare.