Tuning Wiki

What a regeneration is

A regeneration is a controlled oxidation of the soot held in the filter. Carbon leaves as carbon dioxide. The ash stays. The control unit starts one when the soot model, the pressure, or a distance or time limit says the cake is due, and when the driving conditions can support the temperature. It is a burn of soot. It is not a cleaning cycle, not an additive refill, and not a repair for a cracked brick.

There are three ways the heat is obtained. They are often all present on the same car, used according to the journey.

Passive

Passive regeneration is soot oxidising during ordinary driving, with no extra fuel. The usual agent is nitrogen dioxide made by platinum on an upstream oxidation catalyst or on the filter washcoat. That reaction is already useful from about 250 °C, so a loaded motorway run or a long hill can hold the soot mass flat or even reduce it. Oxygen takes over once the brick is in the mid-500s °C or hotter, which a passive drive only reaches on some engines.

A fuel-borne catalyst makes the oxygen path work at a lower temperature, because the metal is inside the soot rather than only on the wall. Passive regeneration on those cars is still passive: the additive was dosed into the fuel earlier, and this journey is only providing the heat. A car that never holds even that lower temperature never regenerates passively. The soot integrator climbs until an active cycle is required.

Active

Active regeneration is the control unit making the filter hot on purpose. The target depends on the coating and the additive. An oxygen burn on a lightly catalysed filter is aimed at the mid-500s to mid-600s °C at the filter inlet. A system that can use nitrogen dioxide, or a fuel-borne catalyst, is calibrated to a lower target because the soot lights earlier. The number in one manufacturer’s data does not transfer to the next brick.

The heat is made by adding fuel where it will burn in the exhaust rather than as torque, and by reducing the air that would cool the gas:

  • A late injection in the cylinder, after the main burn, sends fuel out with the exhaust. An oxidation catalyst or a catalytic washcoat lights it. This is the common light-vehicle method. Fuel that hits the cylinder wall and does not leave can drain into the oil. A cycle that is cut short by the driver switching off repeats that, and the oil level rises. An injector mounted in the exhaust, or a vaporiser ahead of the catalyst, puts the same fuel in downstream of the rings, so the sump is not diluted by the regeneration itself.
  • The intake throttle closes to cut air mass, the EGR valve is held shut, and injection timing is moved so the exhaust valve opens onto hotter gas. Glow plugs are sometimes run during the cycle to stabilise combustion while the air is restricted.
  • On some heavier engines a burner or a hydrocarbon doser sits in the exhaust and is the only source of the extra fuel.

While the cycle runs, idle may rise, the cooling fans may run, stop-start stays off, fuel use rises, and the exhaust smells hot. Those signs are the strategy working. The cycle needs a few minutes at a speed that keeps exhaust flow and temperature up. The conditions that abort it, and the warning that follows, are on particulate filter faults.

The control unit ends the cycle when the soot model has fallen to its residual, or when a maximum time is reached, or when a sensor says the temperature cannot be held. A maximum time that expires with the soot mass still high is a failed regeneration. The reason is then the heat, the air, the additive, or a soot mass so high that the calibration refuses to light it.

Workshop regeneration

A service regeneration is the same chemistry, commanded by a diagnostic tool with the car stationary or on a road the tool specifies. It is used when the load has passed the point at which a normal drive is allowed to light the filter, or when the car cannot be driven in the way an active cycle needs. The tool holds the conditions and watches the temperatures and the pressure.

It is the right tool when the load is soot, the sensors agree, the oil level is safe, and the engine can reach the target. It is the wrong tool when the residual is ash, when a temperature sensor is implausible, or when EGR, boost or injectors are still producing the soot that filled the filter. Lighting a brick that already holds too much soot for its material can melt cordierite or crack a silicon carbide segment. Calibrations that know this refuse the cycle above a soot mass and ask for the filter to be removed.

What should have changed when it finishes

Soot mass down to the residual the calibration uses. Differential pressure, read at a comparable flow and temperature, down to the ash line and no further. Exhaust temperatures that rose in the order the strategy commands, inlet first as the catalyst lights, then the outlet as the soot itself burns. An outlet that never rises, while the inlet gets hot, is fuel burning in the catalyst and little soot burning in the filter. An inlet that never reaches the target is a thermostat, a sensor, an additive, a low fuel level, or a strategy that aborted.

Oil level is checked before and after on engines that post-inject in the cylinder. A rising level is diluted oil, and it is a reason to change the oil rather than to keep commanding cycles. Ash mass, on a control unit that stores one, is unchanged by a successful burn. If the complaint was a full filter and the ash mass was already the thing at its limit, the regeneration did what it can do.