Tuning Wiki

What PAT fluid is

PAT fluid is the workshop name for the fuel-borne catalyst used on an additive-assisted diesel particulate filter. The original-equipment fluids are the Eolys range, from Rhodia and later Solvay, and Infineum F7995. The additive sits in its own tank or in a flexible pouch. A pump meters a small quantity into the diesel when fuel is added. The driver does not pour it into the filler neck, and it is not AdBlue. AdBlue is urea solution, injected into the exhaust for a NOx catalyst. PAT fluid goes into the fuel so that the metal in it is burnt with the diesel and ends up dispersed through the soot.

Soot on an uncoated wall needs roughly 550 to 600 °C before oxygen will burn it at a useful rate. Town exhaust rarely holds that. The metal in the additive is mixed through every soot particle the filter catches, and the burn then starts at a lower temperature. On the early cerium additive that start is commonly described around 450 °C. The filter can regenerate on a shorter, cooler journey than a system that has to make the whole brick that hot with extra fuel. Solvay’s later iron additive is formulated for the same job at a lower metal dose, which is how the additive tank lasts longer and how less ash is left per kilometre.

The system is fitted where the engine was built with an additive-assisted filter. That is most widely the Peugeot, Citroën and DS diesels from 2000 on, and other cars that use those engines. The badge and the year do not choose the fluid. The production date code, the filler colour, and the repair procedure for that car do.

Where the metal goes

The dose is small, a few milligrams of metal per kilogram of fuel on the later iron fluid, quoted by Solvay as 3 to 5 mg/kg. It leaves the injector with the diesel, passes through combustion, and is trapped with the soot. During regeneration the carbon burns and the metal oxide stays. That oxide is ash. Cerium ash from the first generation is why those filters filled on a shorter distance than a later iron system. Regeneration cannot remove it. A low-additive warning and a full-filter warning are different lamps and different jobs.

Refilling the tank does not clean the filter. It restores the ability of the next soot to burn at the temperature the calibration expects. An empty tank on a car that needs the additive is one of the reasons a regeneration never completes. The control unit counts the volume it has pumped and the distance travelled. After a refill that counter has to be reset with a diagnostic routine, or the lamp stays on and dosing stays inhibited even though the tank is full.

The generations

The fluids are not one product that got a new label. The first production additive, Eolys DPX42, is cerium-based. Eolys Powerflex is a later iron-based fluid. Eolys 176 and Infineum F7995 sit between them as the service fluids for the second-generation hardware. Eolys Extend is a further service fluid for specified later cars. Peugeot’s own instruction is that Powerflex does not replace DPX42 and must not be mixed with it, and that Powerflex and Extend must not be mixed with each other. A bottle sold as suitable for every generation does not cancel that.

FluidFillerWhat it isWhat may be added
Eolys DPX42WhiteFirst generation, cerium-based. Service interval quoted around 80,000 km from a tank of about 5 litresDPX42 only
Eolys 176GreenSecond generation. Service interval quoted around 120,000 km from a tank of about 3 litres176, or Infineum F7995 where the procedure for that car allows the change
Infineum F7995GreenThe refill that replaces 176 on the cars specified for itF7995. Not Powerflex. Not DPX42
Eolys PowerflexBlueIron-based. Solvay quotes 1.2 to 1.9 litres of additive for 250,000 km at a fuel consumption of 7 L/100 km. That figure is the additive supply, not the life of the filterPowerflex only
Eolys ExtendBlackLater service fluid for the production dates the procedure namesExtend. F7995 only on the cars whose procedure says the two may meet. Not Powerflex. Not DPX42

Cars that left the factory on the second-generation fluid are refilled with the third-generation fluid named in that car’s procedure, which is F7995 or Extend, not an arbitrary later bottle. DPX42 stays DPX42 for the life of that tank. The organisation code on the vehicle, the OPR, is what the parts catalogue uses to split the ranges. Reading the filler colour is a check. It is not a substitute for the code when a previous refill may already have been wrong.

Tank, pouch and dosing

Early cars have a rigid tank low in the body, with a filler of its own, often in a wheel arch or under the floor. Later cars use a sealed pouch that is replaced as a unit when it is empty. The pump and the pipes are the same idea either way: a measured shot into the fuel tank, triggered by a refuel, so the concentration in the diesel stays in the range the filter was calibrated for. Over-dosing makes ash faster. Under-dosing means the soot will not light at the temperature the regeneration is aiming for, so the cycle runs long, uses more fuel, or fails.

PAT Fluid, the aftermarket brand, is sold in bottles for a rigid tank and in bags for the pouch cars, as a refill for this duty. Matching the generation that is already in the vehicle still applies. Pouring the fluid into the diesel filler, or topping a DPX42 tank with Powerflex because both are called Eolys, puts the wrong metal through the injectors and leaves an ash the service interval was not based on.

What a refill does not fix

The additive warning means the supply is low or the counter says it is low. The filter warning means soot or ash has reached a limit. A refill answers the first. The second needs a regeneration if the load is soot, or a clean or a new filter if the load is ash. The driving symptoms of a blocked filter, and the conditions that stop a regeneration, are on particulate filter faults.