Tuning Wiki

For three-way catalyst operation, common faults and documented components, see Three-way catalytic converters: operation, components and diagnosis.

For lean NOx trap materials, regeneration, faults and documented components, see Lean NOx traps: operation, components and diagnosis.

For diesel oxidation catalyst operation, common faults and documented components, see Diesel oxidation catalysts: operation, components and diagnosis.

A catalytic converter uses a catalytically active material in the exhaust to accelerate chemical reactions that reduce particular pollutants. A petrol three-way catalyst, diesel oxidation catalyst and selective catalytic reduction catalyst do different jobs; the metal can alone does not identify the chemistry inside. Performance depends on exhaust composition, temperature, flow and the condition of both the engine and the aftertreatment.

This guide covers converter types, the substrate and catalytic media, operation, failures and diagnosis. For the whole system see petrol and diesel emissions, lambda sensors, emissions testing equipment and SCR with urea solution.

What a catalyst does

A catalyst speeds a reaction without being consumed as a reactant in the intended chemical cycle. The exhaust gases contact active sites on the converter's internal coating. Some gases are oxidised; others are reduced. Actual conversion is neither instantaneous nor perfect: it changes with catalyst temperature, mixture, flow, age and contaminants. A converter does not remove carbon dioxide or replace correct combustion. AECC: catalysts.

TypeMain jobConditions and distinctions
Three-way catalyst (TWC)Oxidises CO and hydrocarbons and reduces NOx.Used with suitable spark-ignition engines and high conversion near stoichiometric mixture. Oxygen-rich exhaust makes simultaneous NOx reduction difficult.
Oxidation catalyst / diesel oxidation catalyst (DOC)Oxidises CO and hydrocarbons; on diesels it can also oxidise some NO to NO₂ and hydrocarbon material associated with particles.Works in oxygen-rich exhaust; it is not a substitute for the diesel's NOx reduction system or a particulate filter.
Lean NOx trap (LNT) / NOx storage catalystStores NOx during lean operation, then releases and reduces it during a controlled rich interval.Has storage and catalytic components; some designs need periodic sulphur removal. Not all lean-burn engines use one.
Selective catalytic reduction (SCR)Uses a reductant, normally ammonia derived from injected urea solution, to reduce NOx in oxygen-rich exhaust.Depends on dosing, mixing, temperature and catalyst formulation. The SCR catalyst may be separate or integrated with a filter.
Catalysed DPF or GPF/OPFCombines filtration with a catalytic coating; the coating's chemical function depends on the design.A wall-flow filter traps particles, unlike the usual flow-through catalyst. A coated GPF may have a three-way coating; a DPF may carry an SCR coating.

These functions are often combined in a system, not necessarily in a fixed order or one separate can for each job. Identify the engine, vehicle emissions system and individual assembly before choosing a replacement. AECC: catalyst technologies; AECC: wall-flow filters; AECC: NOx adsorbers.

Inside a converter: substrate, washcoat and active materials

The assembly commonly has a stainless-steel outer casing, a mounting or support mat, a shaped substrate and a catalytic coating. These are separate layers with different jobs. The substrate provides many gas passages and supports the coating; the washcoat supplies a much larger microscopic surface area for the dispersed active material. The can is not itself the precious-metal catalyst. Design and material choices vary with operating temperature, position, emissions target and cost. AECC: substrates and coatings; Corning: ceramic substrate.

Flow-through ceramic and metal substrates

A common flow-through monolith resembles a honeycomb: many small parallel channels run through the core and exhaust flows along their coated walls. The open channels provide contact area while allowing gas through. Cell density is commonly given in cells per square inch (cpsi); wall thickness, channel shape, coating, length and volume matter as well. AECC describes available substrates at several densities, including 400, 600 and 900 cpsi and higher designs. Thinner walls reduce thermal mass and help warm-up, but the design must balance strength, thermal durability, exposed coating area and flow resistance. A higher or lower number alone does not establish a converter's conversion efficiency, pressure drop, durability or road approval.

  • Ceramic cordierite: a magnesium aluminosilicate ceramic widely used as a honeycomb substrate. Low thermal expansion helps resistance to thermal shock. Thin walls reduce the amount of material that must warm up, but the whole design must also tolerate vibration, heat and assembly stresses. Corning: cordierite.
  • Metallic foil: thin corrugated and flat metal foils can form honeycomb channels. The substrate and coating are selected for the application; thin-wall metal and ceramic designs offer different heat-up, mechanical and packaging trade-offs. A metallic core is not inherently a guarantee of higher performance or emissions compliance. AECC: substrate options.
  • Other configurations: older converters also used catalyst-coated pellets rather than today's common monolithic honeycomb. Some SCR catalysts use an extruded structure in which active material is incorporated into the body, rather than relying solely on a coating on an inert substrate. AECC: extruded catalysts.

Cell density and tuning: a “100-cell” or “200-cell” description describes nominal channel density, not the composition of the washcoat or the full assembly's performance. Open area, wall thickness, catalyst loading and formulation, flow, volume, temperature and ageing all affect the result. Compare an appropriate approved assembly and manufacturer data for the specific vehicle; a cell count or a clean idle result is not proof of compliance.

Wall-flow filters are different

A particulate filter typically has alternate channels plugged at opposite ends. Gas passes through porous ceramic walls, which trap particles; a flow-through converter's channels normally remain open from end to end. Common filter materials include cordierite, silicon carbide and aluminium titanate. A filter can be uncoated or have a coating chosen for soot oxidation, three-way conversion or SCR; this does not make every filter or coating interchangeable. See DPF substrates and coatings and petrol particulate filters. AECC: filters.

Washcoat, oxygen storage and precious metals

A washcoat is a porous, high-surface-area layer deposited on a substrate. Alumina and other stabilised oxides can support finely dispersed active materials; washcoat compositions, coating arrangement and loading are specific to the design. In many three-way catalysts ceria-containing materials can store oxygen during lean excursions and release it during rich excursions, helping buffer brief mixture fluctuations. This does not make a conventional three-way catalyst an effective NOx reducer during sustained lean operation. Ceria–zirconia and other materials can also contribute to thermal stability. AECC: three-way catalysts; BASF: converter structure and coatings.

  • Platinum (Pt) and palladium (Pd): platinum-group metals used in selected catalyst formulations, including for oxidation of CO and hydrocarbons. Diesel oxidation catalysts often use Pt and/or Pd; the blend and loading are formulation-dependent.
  • Rhodium (Rh): important in many three-way formulations for reducing NOx. A particular converter need not contain all three metals, and the metal roles overlap with the rest of the chemistry.
  • Storage and base-metal materials: a lean NOx trap also uses NOx storage components, often alkaline-earth materials such as barium compounds, alongside catalytic materials. SCR frequently uses copper- or iron-containing zeolites or, in other applications, vanadium-based catalysts. These are different technologies and should not be assumed to share a three-way catalyst's washcoat. US Department of Energy: lean NOx trap development; AECC: emissions-control technologies.

The exact ratios and mass of Pt, Pd, Rh or other materials cannot be inferred reliably from the casing, cell count or vehicle fuel. Avoid fixed precious-metal values or universal washcoat recipes. Spent converters can contain recoverable metals; use an appropriate recycling route.

Three-way catalyst and lambda control

Some converters use electrical heating to speed cold-start light-off. BMW’s E38 750iL M73TU E-CAT is one documented example; see the three-way catalyst guide for its dual-battery arrangement, an earlier ALPINA system and diagnostic cautions. BMW technical training.

On a suitable warmed petrol engine, the ECU uses upstream oxygen-sensor feedback to control mixture around lambda 1. The catalyst oxidises CO and hydrocarbons to CO₂ and water and reduces NOx to nitrogen under favourable conditions. Oxygen-storage materials smooth short fluctuations, while sustained rich or lean operation reduces one or more conversion functions. The downstream sensor on many systems helps monitor catalyst oxygen-storage behaviour. The role of each sensor and the diagnostic strategy vary by vehicle. HELLA: lambda sensors and catalyst monitoring.

Light-off describes the onset of useful conversion as the catalyst warms; the exact temperature and conversion threshold depend on the reaction and test. Close-coupled catalysts and thin-wall substrates can warm quickly, but must withstand high temperatures. A colder underfloor catalyst may serve a different role in the system. A cold-start failure or short journey cannot be assessed solely from a warm idle result. AECC: catalyst light-off.

Diesel oxidation, NOx storage and SCR

A DOC converts CO and hydrocarbons in oxygen-rich exhaust. It can oxidise NO to NO₂; this can assist certain downstream reactions and passive soot oxidation where the system and conditions allow. A DOC does not generally reduce NOx to nitrogen under lean conditions. A DPF traps particles; soot can be oxidised in regeneration, while ash persists. See diesel particulate filters and DPF regeneration.

An LNT stores NOx in lean exhaust and periodically uses a richer phase to release and reduce it; sulphur can occupy storage sites, requiring a vehicle-specific desulphation strategy. SCR instead uses ammonia generated from urea solution on most road vehicles; the catalyst promotes NOx reduction in oxygen-rich exhaust. Sensors, temperature, dosing and ammonia control affect the result. Some layouts combine SCR and the filter or use an ammonia-slip catalyst. Refer to SCR with urea solution; AECC: adsorbers.

Common problems, damage and symptoms

Failure mechanismPossible signs and investigation
Ageing, overheating or misfireLoss of active surface or oxygen-storage performance; severe overheating can damage or melt the substrate. Misfire or excess unburned fuel can overheat a catalyst. Repair the engine fault before fitting a replacement.
Poisoning or contaminationLead, some fuel or oil contaminants, coolant ingress and other deposits can impair activity. Identify and repair the source; appearance alone does not measure conversion.
Broken, loose or restricted coreRattle, restriction or loss of power can occur, but exhaust parts, turbo and engine faults can produce similar symptoms. Inspect and measure as directed for that system.
Exhaust leaks or sensor faultsOutside air can distort sensor and gas readings. Wiring, heater circuits, mixture control and sensor response can produce misleading catalyst-monitor faults.
Diesel/SCR system faultIncorrect exhaust temperature, NOx measurement, fluid quality or dosing may affect results without the catalyst brick being the failed component.

A catalyst-efficiency code such as P0420 is evidence that an ECU monitor detected performance below its threshold under its test conditions; it does not on its own prove that the converter is defective. Check the exact code and vehicle diagnostic procedure, engine faults, exhaust leaks and both sensor circuits. HELLA: exhaust aftertreatment diagnosis; Bosch: lambda sensor diagnosis.

Practical testing and replacement

  1. Identify engine, fuel, original exhaust and all catalyst/filter positions. Record codes, freeze-frame data, temperatures and the reported symptoms before clearing faults.
  2. Check misfires, ignition, fuel delivery, oil or coolant consumption, intake and exhaust leaks and related sensor or heater faults. A good new converter may fail again if the cause remains.
  3. Use an appropriate scan tool to check readiness, commanded and measured mixture, sensor signals and catalyst-monitor results under the manufacturer's specified conditions. A relatively smooth downstream trace on a suitable system may be consistent with oxygen storage; a trace or generic waveform alone is not a universal pass/fail test.
  4. Use a calibrated gas analyser and the specified test conditions when assessing CO, HC, O₂ and calculated lambda; evaluate sampling leaks and the engine's operating state. For suspected restriction, use the vehicle manufacturer's pressure or other diagnostic procedure. A simple universal inlet/outlet temperature difference, single gas value or cell-count number cannot establish full catalyst performance.
  5. Fit the specified compatible assembly, sensors and gaskets; address the failure cause, perform prescribed checks or adaptations and verify the repair. Do not reset or clear a monitor as a substitute for repair.

Catalyst and exhaust temperatures can cause burns or fires. Allow components to cool, keep combustible materials away and use suitable exhaust extraction during engine operation. HSE: vehicle exhaust emissions.

UK MOT and replacement requirements

The DVSA MOT inspection manual, section 8 specifies the applicable inspection for original emissions equipment, leaks, malfunction indicators and tailpipe tests. A pass on a warm CO, HC and lambda check does not prove NOx conversion or whole-cycle type-approval performance.

The Department for Transport guidance on catalytic converters describes type-approval requirements for replacements fitted to vehicles registered on or after 1 March 2001, and equivalent-performance guidance for earlier vehicles. Check the current guidance, the vehicle's applicability and the part's approval and identification before supply or fitting. A converter's cell count, external appearance or advertised performance is not a substitute for checking the correct approval.

Sources and related reading