Tuning Wiki

A three-way catalytic converter (TWC) helps a suitable spark-ignition engine control carbon monoxide (CO), unburned hydrocarbons (HC) and oxides of nitrogen (NOx). It oxidises CO and HC and reduces NOx. Conversion depends on catalyst temperature, the exhaust mixture, flow and condition; a catalyst fault code alone does not prove the converter has failed.

For the wider system see petrol and diesel emissions, catalytic converter materials, lambda sensors and diesel oxidation catalysts.

What the three ways do

Exhaust constituentPrincipal reactionWhat affects conversion
Carbon monoxide (CO)Oxidation to carbon dioxide (CO₂).Requires suitable catalyst temperature and oxygen availability.
Hydrocarbons (HC)Oxidation principally to CO₂ and water.Cold starts, misfires, rich mixtures and a cold or contaminated catalyst can affect results.
Nitrogen oxides (NOx)Reduction principally to nitrogen (N₂), using available reducing species in suitable exhaust conditions.Sustained oxygen-rich exhaust makes simultaneous NOx reduction difficult for a conventional TWC.

These processes occur on the coated surface and their effectiveness changes with exhaust chemistry. The catalyst accelerates reactions; it is not a fuel filter, does not remove CO₂ and cannot correct a persistent engine fault. See AECC: catalyst operation.

Lambda and closed-loop control

Lambda is the actual air–fuel ratio divided by the stoichiometric ratio for the fuel. Lambda 1 is the theoretical balance; below 1 is rich, above 1 is lean. Many petrol engines use upstream oxygen-sensor feedback to adjust fuel around this point, giving the TWC a narrow window in which all three conversions can work effectively. Closed-loop control is not necessarily active in every state; cold start, high load and fuel cut are examples that depend on the calibration. AFR and lambda; AECC three-way catalysts.

In many catalysts ceria-containing materials store oxygen during lean swings and release it during rich swings. This buffers short changes; it does not make a conventional three-way catalyst an effective NOx reducer during sustained lean operation. Some lean-burn engines use a separate NOx storage catalyst or other NOx aftertreatment.

The upstream lambda sensor commonly supports mixture control. A downstream sensor commonly helps the ECU monitor oxygen-storage performance, and some systems also use it for mixture adaptation. A smoother downstream signal than the upstream signal can be expected on a suitable warm, steady system, but waveforms vary with sensor type, location, load and strategy. A downstream trace resembling the upstream trace is a clue, not an automatic converter verdict. Exhaust leaks, mixture faults and sensor or wiring problems must also be assessed. HELLA: lambda sensors and catalyst monitoring.

Inside the converter

Common assemblies use a ceramic or metal flow-through honeycomb inside a metal casing. The monolith supplies many gas passages; a porous, high-surface-area washcoat carries finely dispersed active material. Alumina, ceria and other stabilised oxides can be used; compositions, layer arrangements and loadings vary. Platinum (Pt), palladium (Pd) and rhodium (Rh) are used in different combinations. Pd and Pt can promote oxidation, while Rh is important for NOx reduction in many formulations; their roles overlap and a particular unit need not contain all three. AECC: substrates and catalytic coatings; BASF: three-way coating example.

Synthetic cordierite is a widely used low-expansion ceramic; metallic foil can form thin honeycomb channels. Cell density, wall thickness, washcoat, volume and installation affect heat-up, contact area, durability and flow resistance. A nominal “100-cell” or “200-cell” figure does not by itself establish conversion, pressure drop or road approval. A particulate filter has a different wall-flow structure and traps particles; a catalysed petrol particulate filter can combine filtration with a three-way coating on particular vehicles. Corning: cordierite; AECC: filters.

Cold start, light-off and location

Catalytic activity rises as the brick warms. “Light-off” describes the temperature region where conversion becomes effective, with the precise definition depending on the pollutant and test. A close-coupled catalyst near the engine can warm sooner than an underfloor unit, but must tolerate severe heat. Some engines have more than one brick, combined exhaust manifolds or separate banks. Identify the correct assembly and sensor positions before diagnosis. AECC: light-off.

Cold-start control can include changed ignition or fuelling; on some cars secondary air injection helps oxidise CO and HC and warm the converter. A warm idle gas test is useful for its prescribed purpose but does not reproduce cold-start emissions or establish performance under all loads.

Electrically heated catalysts and BMW V12 examples

Some exhaust catalysts contain an electrically heated element or substrate. Electrical energy warms the catalyst during the cold-start period, helping it reach useful conversion temperature sooner; the detailed heater arrangement and control strategy vary. This is different from the small heater inside an oxygen sensor and from secondary air injection. A heated catalyst still relies on the right exhaust mixture and a sound catalytic coating. Emitec: electrically heated catalyst.

1999 BMW E38 750iL, M73TU V12: BMW technical training identifies an electrically heated catalyst, called E-CAT, on the 1999 E38 750iL. The higher electrical load during starting led to a dual-battery system: a starter battery supplies starting and E-CAT operation, while the second battery supplies the vehicle electrical system, with an electronically controlled isolation switch. These details come from the documented BMW example; check the VIN, model year, market and wiring information rather than assuming every M73 or E38 has the same equipment. BMW technical training, Power Supply and Bus Systems, pages 16–17; BMW M73 engines.

2001 750iL service-data example: an ALLDATA description of the M73TU shows a hydrocarbon adsorber at the front of each exhaust assembly, followed by an electrically heated coil and downstream catalyst stages. It describes a separate E-CAT control module and simultaneous heater control for the two banks. In that documented configuration the heaters run for at most 30 seconds after start, and can run for less or remain off depending on monitored conditions. The service data lists coolant and battery temperatures, previous operation and other enable conditions, so a silent heater after an arbitrary restart is not a valid failure test. These values are specific to that 2001 service description, not specifications for every heated catalyst or the ALPINA arrangement. ALLDATA, 2001 BMW 750iL E-CAT description.

Earlier BMW ALPINA B12 5.7 Switch-Tronic: a 1996 SAE paper by ALPINA, BMW and Emitec describes an electrically heated catalyst in the limited-series V12 for Europe and Japan. It describes alternating heating of the two converters to manage the electrical demand. That example is separate from the later BMW dual-battery system and does not establish California-market fitment. Hanel, Otto and Brück, SAE 960349, 1996.

Modern electrically heated designs also exist for petrol and diesel aftertreatment. For example, Emitec describes versions for three-way, oxidation, NOx storage and SCR catalysts with 12-, 24- or 48-volt applications. Those are product-family possibilities, not electrical specifications for the BMW system. Emitec EMICAT product information.

Common problems and checks on heated catalysts

A heater circuit fault or low supply may prevent the intended rapid warm-up; a failed relay or control, connection or wiring fault, damaged heating element, or battery and charging issue are possibilities depending on the design. A hot-running catalyst can still have a heater problem that is not resolved by replacing an oxygen sensor. Conversely, a catalyst-efficiency code is not proof the heating element is defective. Record the fault, coolant and exhaust temperatures, battery condition and heater-enable state, then follow the specific vehicle's fault tree and high-current electrical test procedure. A heater that is off outside its commanded cold-start or diagnostic conditions is not automatically faulty.

Heated catalysts have high-current connections and hot exhaust components; modern systems may use other supply voltages. Follow the exact vehicle's isolation and service instructions, allow components to cool and do not bridge relays or apply a generic voltage or current test to an unknown heater. No universal heating time, battery arrangement or pinout is implied by these examples.

Common problems and symptoms

ProblemPossible signsFirst checks
Ageing or loss of oxygen-storage capacityA catalyst-efficiency monitor fault, high CO or HC in the appropriate test, or deteriorating conversion.Confirm test conditions, exhaust integrity and upstream/downstream sensor function and mixture; a fault code is not proof of a failed brick.
Misfire, excess fuel or overheatingLoss of performance, hot exhaust, damaged or melted substrate; the engine fault may precede catalyst damage.Investigate ignition, injectors, mixture, timing and underlying misfire first. Avoid continuing the conditions that caused excessive temperatures.
Oil, coolant, lead or other contaminationA contaminated element or reduced activity can accompany oil consumption, coolant loss or incorrect fuel/additives.Find the source before replacing a converter. Appearance and a single gas reading cannot measure the remaining catalytic activity. Walker: converter failure causes.
Broken, loose or restricted substrate or exhaust leakRattle, exhaust noise, restriction or a monitor fault. Other exhaust parts and engine faults can give similar symptoms.Inspect the assembly and exhaust, and use the maker’s specified restriction test if required. Do not assume low power alone proves blockage.
Oxygen sensor, wiring or software-related faultImplausible feedback, mixture compensation or efficiency code, possibly with a sound catalyst.Check the correct bank, heater, wiring, leaks, operating state and relevant technical bulletins. Honda documents one model-specific P0430 software example where the sensor input could be misinterpreted: Honda bulletin 17-036.

Workshop diagnosis and testing

  1. Identify the system. Record vehicle, engine, fuel, bank, converter positions, diagnostic codes, freeze-frame data, recent repairs and applicable bulletins. Do not assume bank numbering or sensor type without the wiring and service information.
  2. Check engine and exhaust condition. Investigate misfires, mixture, air leaks, fuel pressure, oil or coolant consumption, exhaust leaks and sensor heater or circuit faults. Repair confirmed faults that can invalidate the monitor or damage a new converter.
  3. Check readiness and live data. At the manufacturer's specified operating conditions compare requested and actual lambda, relevant trims, upstream and downstream signals and catalyst monitor results. A generic oscillation pattern or a fixed voltage is not a universal pass/fail criterion.
  4. Measure as directed. An approved and calibrated gas analyser measures exhaust CO, HC, CO₂ and O₂ and calculates lambda from the sample. Check exhaust and sample integrity, warm-up and applicable limits. High CO or HC may be caused by combustion, mixture, sampling or the converter; a normal idle result does not prove NOx conversion through a driving cycle. See emissions testing equipment.
  5. Confirm restriction only with an appropriate test. Follow the vehicle-specific pressure measurement or other authorised procedure. An inlet/outlet temperature difference, rattle or code alone is not a universal test of conversion or blockage.
  6. Repair and verify. Fit the correct type-approved assembly where required, sensors and seals; use the specified torque and handling instructions. Complete the required monitor and checks after repair. Clearing a code does not restore a catalyst.

Exhausts and catalysts remain hot after running and can ignite nearby combustible material. Allow cooling as needed and use extraction during running tests. HSE: vehicle exhaust emissions.

Documented component examples

These historical examples come from manufacturer service documents, not an exhaustive fitment catalogue. A part number can identify a converter with a pipe or other hardware; left and right units and market approvals can differ. Confirm the current part, engine, build, market, VIN and supersession using the manufacturer's current parts information.

ReferenceDocumented component and applicationSource and limits
GM 20929196Right three-way converter assembly with exhaust pipe for specified 2013–2018 Cadillac XTS and 2014–2018 Chevrolet Impala with 3.6 L LFX engine.GM bulletin 17-NA-321 covers vehicles built through 1 October 2017 and distinguishes North America/export from Korea. The bulletin concerns a flange crack; it is not a blanket fitment instruction.
GM 84216836Left three-way converter with exhaust pipe for the bulletin's North America and export regions except Korea.
GM 84216838Left three-way converter with exhaust pipe listed for Korea in that bulletin; the same number appears in a separate, narrowly scoped California-certified vehicle recall. Check the vehicle and document rather than assuming those applications are identical.
Acura 18190-RWC-A00Warm-up three-way catalyst in a service bulletin for 2007–2009 RDX and specified VIN ranges of 2010 RDX 2WD and SH-AWD.Acura bulletin 12-036 also specifies a separate gasket and a fuel-tank repair for the described condition. US-market bulletin; check VIN and current catalogue.
Nissan 140E2-9HS0A / 140E2-3TA0AExhaust manifold with three-way catalyst for selected 2018 Altima L33 QR25DE vehicles in campaign PC717; the bulletin distinguishes California-emissions and non-California configurations.Nissan NTB20-027. The related air–fuel and oxygen sensors are listed separately; campaign scope and current parts must be checked by VIN.
Nissan 140E2-6FJ0AExhaust manifold with catalyst for the bulletin's specified 2018 Rogue T32 QR25DE; its parts table states a September 2016–August 2018 build range.Nissan NTB20-027; verify the campaign and vehicle identity rather than treating the number as universal.
Honda 18190-RTW-A00Converter listed in a warm-up three-way catalyst diagnostic bulletin for specified 2014–2016 CR-Z vehicles.Honda service bulletin 22-040 directs diagnosis and software checks before ordering a part; applicability is specific to its stated vehicle and market.

These references describe assemblies, not precious-metal content, cell density or universal replacement approval. Similar appearance or an identical fault code does not establish interchangeability.

UK MOT and replacement

The DVSA MOT manual, section 8 sets out the applicable visible emissions-equipment checks, malfunction indicator checks and petrol gas tests. Test selection depends on the vehicle and its first-use date. A CO/HC/lambda pass at the specified conditions is not a direct NOx measurement or a type-approval driving-cycle result.

Department for Transport guidance states type-approval requirements for fitting replacement catalytic converters to applicable vehicles registered on or after 1 March 2001, with guidance for earlier vehicles. Check the current rules, applicable approval and exact vehicle before supply or installation.

Sources and related reading