Tuning Wiki

15 matching pages

  • Delphi CRDReference hub

    The CRD2 name on Delphi diesel files for Mercedes-Benz and the Jeep 2.2 CRD. Alientech pairs it with DCM 3.5. The piezo OM651 is generation 4.1.

    Engine ECU   Updated

  • Delphi CRD bench connection pinout

    Bench-connection power pins of the Delphi CRD (HW 50.05, Mercedes-Benz application) on the 96-way A and 58-way B connectors; programming is via BDM pads on the circuit board.

    Engine ECU   Updated

  • Delphi DCM 1.2Reference hub

    DCM 1.2 identification, Renault K9K diagnostic scope, injector correction and documented application examples.

    Engine ECU   Updated

  • Delphi DCM 1.2 bench connection pinout

    Bench-connection pins (+12 V, ground, K-line) of the Delphi DCM 1.2 in Citroen, Peugeot and Renault applications, with every cavity of the 112-way T1/T2/T3 header drawn.

    Engine ECU   Updated

  • Delphi DCM 3.4Reference hub

    DCM 3.4 generation evidence, Renault and Dacia diagnostic coverage, processor listings and identification limits.

    Engine ECU   Updated

  • Delphi DCM 3.4 bench connection pinout

    Bench-connection pins for the Delphi DCM3.4 diesel ECU in Citroen/Peugeot applications: three-block 128-cavity header with battery, ignition, ground, K-line and CAN pins highlighted.

    Engine ECU   Updated

  • Delphi DCM 1.1Reference hub

    Delphi DCM 1.1: first-generation 16-bit Euro 3 diesel controller, named for the Renault K9 as well as Kia and Ford Lynx, with identification limits for early 1.5 dCi units.

    Engine ECU   Updated

  • Delphi DCMReference hub

    Delphi diesel control-module generations from the 2007 manual. Generation 3.5 is the solenoid OM651 and the DW10C. Later repair lists use the same numbers differently.

    Engine ECU   Updated

  • Delphi dieselReference hub

    Delphi common-rail diesel control as described in the 2007 DDGX200 manual: the DCU, DFI 1 injectors, C2I and C3I codes, and the DCM generations.

    Engine ECU   Updated

  • Delphi petrolReference hub

    Delphi and Delco petrol controllers. HSFI-2.x is recorded on the Z16SE. Multec S, Delco DNHP, is recorded on the Zafira A Z16XE. The two are not the same unit.

    Engine ECU   Updated

  • Delphi DCM3.7 and DCM3.7APReference hub

    DCM3.7 and DCM3.7AP identification, selected road vehicle and off-highway coverage, and programming method limitations.

    Engine ECU   Updated

  • Delphi Delco Multec HSFI-2.x

    Identification, sourced Opel and Vauxhall application examples, fault investigation and replacement considerations for HSFI-2.x petrol controllers.

    Engine ECU   Updated

  • Delphi DCM6.1 and DCM6.2

    Identification, documented processor and vehicle examples, and programming considerations for Delphi DCM6.1 and DCM6.2 diesel ECU variants.

    Engine ECU   Updated

  • Delphi CRD3 and CRD3P

    CRD3 and CRD3P diesel ECU identifiers, selected Mercedes-Benz and Infiniti coverage examples and workshop identification.

    Engine ECU   Updated

  • DelphiReference hub

    Delphi and Delco engine controllers, grouped as diesel DCM and CRD common rail, and petrol Delco and Multec. The company name follows the contract. The label is the identification.

    Engine ECU   Updated