Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Audi, SEAT, Škoda, Volkswagen

Changes from revision 3 to revision 4

Removed text is struck through; added text is highlighted.

This comparison covers selected aftermarket high-pressure fuel pump (HPFP) and low-pressure fuel pump (LPFP) products for the 2.0 TFSI EA113 and 1.8/2.0 TSI/TFSI EA888. Fitments are supplier examples, not proof that a kit fits every engine in a family. Check the engine code, vehicle and market, original pump or basket, drivetrain, fuel, ECU software and current supplier instructions. Turbocharger power claims and pump capacity claims depend on the whole system and test conditions.

How to compare specifications

The HPFP supplies the direct-injection rail; the LPFP supplies it from the tank and can also feed port injection where fitted. An internal HPFP kit replaces components in a compatible existing pump; an assembled pump is a different purchase. An auxiliary LPFP can work alongside the existing in-tank pump, while other kits replace or modify the tank assembly. A high-pressure pump's larger geometric displacement can increase available volume without commanding higher rail pressure. APR describes the distinction for its Gen 3 pump.

Percentages below are the manufacturers' stated improvements against their own stock references; geometric displacement, measured flow and piston diameter are not interchangeable measures. LPFP litres-per-hour ratings depend on differential pressure, voltage, fuel and test method. Where the supplier does not state these conditions, the nominal figures are not directly comparable as installed flow.

High-pressure pump examples

Autotech 10-127-100K: EA113 early 2.0 TFSI, including the listed Mk5 GTI, Mk6 Golf R and 8P S3 examples. Internal kit, 9.8 mm piston; Autotech claims up to 50% more flow than its original-pump reference. Integrated Engineering IEFUVC3: EA113 2.0 TFSI, including the listed Mk5 GTI and Mk6 Golf R. Complete new pump with upgraded internals; IE states 50% greater displacement and approximately 600 hp at 7,500 rpm with an appropriate setup. The power figure is a supplier claim, not a guaranteed limit for another engine or fuel. APR MS100016: selected EA113 2.0 TFSI applications, including Mk5 GTI and Mk6 Golf R. Complete new pump; APR claims 41% greater displacement. The separately listed MS100017 rebuild uses the customer's pump. Autotech 10-127-101K: specified longitudinal EA888 Gen 2 2.0T Audi applications. Internal kit with an 11.5 mm piston; the supplier's examples include 2009–14 B8 A4/A5/A6/Q5 and TT. Verify the fitted pump rather than assuming every Gen 1 or Gen 2 pump accepts the kit. Nostrum H086-0348: specified EA888 CCTA/CBFA, complete standard-bore kit. Nostrum claims 36% more flow and specifies 180 bar maximum operating pressure and a custom tune. Its catalogue lists 1.19 cc/rev geometric displacement with the stock cam. Nostrum H086-0633: specified EA888 CCTA/CBFA, complete big-bore kit. Nostrum claims 63% more flow, specifies 240 bar maximum operating pressure and requires custom tuning; its catalogue lists 1.43 cc/rev geometric displacement with the stock cam. Neither maximum rating is an instruction to command that pressure on another system. Nostrum H136-0570: selected EA888 rest-of-world applications; supplier states 33% more displacement, 1.43 cc/rev and a 200 bar maximum. Check original pump and exact engine compatibility; the product page specifies tuning. Autotech 10-127-203K: selected EA888 Gen 3 MQB applications. Internal kit with an 11.66 mm piston. Autotech notes that some non-US 1.8 pumps and certain CPLA/CPPA sealed units do not accept this design. APR Gen 3 Hitachi HPFP: selected EA888 Gen 3 applications with compatible Hitachi pumps. APR claims 37% more displacement and lists assembled or rebuild options. Nostrum H136-0568: selected EA888 Gen 3 2.0T applications. Complete pump, claimed 36% greater flow and 200 bar maximum operating pressure; the supplier specifies tuning.

EA888 Evo4 high-pressure components and operating pressures differ from earlier examples. Do not assume a Gen 3 internal kit fits a Gen 4 pump: confirm the exact pump and hardware with the manufacturer. EcuTek's Evo4 guide describes a 35 MPa (350 bar) direct-injection system for its application.

Low-pressure pump examples

APR MS100078 FWD and MS100071 AWD: selected EA113 and EA888 Gen 1 applications. Auxiliary inline pump and controller retain the factory in-tank pump. APR's description states 255 L/h, but its specification table states 225 L/h; test conditions are not specified. Obtain clarification and check the documented tank/filter and drivetrain restrictions. JDY dual-pump kit: specified EA113 Mk6 Golf R and related FWD/AWD variants. Supplier lists Walbro 450 or 525 pump options; its power claim depends on the complete fuel system, including supplemental injection where required. Stratified Mk6 GTI pump assembly: EA888 Mk6 GTI example, with AEM 340 L/h or Hellcat 525 L/h pump options. The supplier recommends suitable tuning and offers controller options. Test pressure and voltage are not stated. APR MS100123: selected EA888 Gen 3 factory-MPI applications. APR specifies a 305 L/h in-tank pump with factory PWM-controller integration, ethanol-compatible hardware and compatible software. Its nominal rating does not state pressure and voltage. CTS Stage 3 CTS-FPK-004-450: selected Mk7/Mk7.5 EA888 Gen 3 MQB vehicles with the listed 5Q0919051BK/BM baskets. Uses a nominal Walbro 450 L/h E85-compatible pump; CTS specifies basket modification and software, and strongly recommends an upgraded controller. CTS Stage 3.5: selected EA888 Gen 3 MQB applications with a nominal Walbro Hellcat 525 L/h pump. Check basket, controller and software requirements for the actual car. Unitronic UH017-FLA: Mk8 GTI EA888 Evo4. Complete brushless pump and basket with controller and harness; Unitronic does not publish an L/h rating on the product page and specifies its compatible software. RTMG 901-1644: selected EA888 Gen 4, including Mk8 Golf R and 8Y S3. Retains the OEM brushless pump and adds a staged Walbro 450 and controller. RTMG lists a 6.7 bar standard system configuration; that is not a specified test pressure for the pump's nominal 450 rating.

Using the comparison during a turbo upgrade

Check the turbo kit and tune supplier's fuel and hardware requirements for the exact version. Where supported, log low-side supply pressure, high-pressure request and actual, lambda target and measured lambda, engine speed, fuel composition and relevant faults under repeatable conditions. A larger LPFP cannot by itself correct an undersized HPFP or injector, and a high-pressure upgrade cannot compensate for inadequate tank supply. Injector flow, injection time, pressure control, wiring, controller capability and pump-basket refill also matter.

Establish a healthy mechanical baseline and confirm the appropriate ECU calibration before loading the engine. Fuel-system work, particularly direct injection, requires the vehicle-specific pressure-relief and installation procedure. Sources are supplier product descriptions and catalogues accessed 17 November 2026; capacities and compatibility must be checked with the relevant supplier for the actual configuration.

Turbo upgrade guides: See EA113 K03-to-K04 and turbo kits, EA888 Gen 1/2 K04 conversions, and EA888 Gen 3/Evo4 turbo upgrades for matched supplier packages and their specific fuelling requirements.

Related injector upgrades: A larger pump and larger injectors address different restrictions. Compare selected parts and their measurement conditions in the EA113 and EA888 injector upgrade comparison.

Earlier 1.8T 20V: This page covers selected later direct-injection engines. The earlier port-injected 1.8T uses different fuelling hardware; see the 1.8T injector and fuel-pump guide for electric pump kits and module fitment.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: EA113 and EA888 fuel pump upgrade comparison

This comparison covers selected aftermarket high-pressure fuel pump (HPFP) and low-pressure fuel pump (LPFP) products for the 2.0 TFSI EA113 and 1.8/2.0 TSI/TFSI EA888. Fitments are supplier examples, not proof that a kit fits every engine in a family. Check the engine code, vehicle and market, original pump or basket, drivetrain, fuel, ECU software and current supplier instructions. Turbocharger power claims and pump capacity claims depend on the whole system and test conditions.

How to compare specifications

The HPFP supplies the direct-injection rail; the LPFP supplies it from the tank and can also feed port injection where fitted. An internal HPFP kit replaces components in a compatible existing pump; an assembled pump is a different purchase. An auxiliary LPFP can work alongside the existing in-tank pump, while other kits replace or modify the tank assembly. A high-pressure pump's larger geometric displacement can increase available volume without commanding higher rail pressure. APR describes the distinction for its Gen 3 pump.

Percentages below are the manufacturers' stated improvements against their own stock references; geometric displacement, measured flow and piston diameter are not interchangeable measures. LPFP litres-per-hour ratings depend on differential pressure, voltage, fuel and test method. Where the supplier does not state these conditions, the nominal figures are not directly comparable as installed flow.

High-pressure pump examples

  • Autotech 10-127-100K: EA113 early 2.0 TFSI, including the listed Mk5 GTI, Mk6 Golf R and 8P S3 examples. Internal kit, 9.8 mm piston; Autotech claims up to 50% more flow than its original-pump reference.
  • Integrated Engineering IEFUVC3: EA113 2.0 TFSI, including the listed Mk5 GTI and Mk6 Golf R. Complete new pump with upgraded internals; IE states 50% greater displacement and approximately 600 hp at 7,500 rpm with an appropriate setup. The power figure is a supplier claim, not a guaranteed limit for another engine or fuel.
  • APR MS100016: selected EA113 2.0 TFSI applications, including Mk5 GTI and Mk6 Golf R. Complete new pump; APR claims 41% greater displacement. The separately listed MS100017 rebuild uses the customer's pump.
  • Autotech 10-127-101K: specified longitudinal EA888 Gen 2 2.0T Audi applications. Internal kit with an 11.5 mm piston; the supplier's examples include 2009–14 B8 A4/A5/A6/Q5 and TT. Verify the fitted pump rather than assuming every Gen 1 or Gen 2 pump accepts the kit.
  • Nostrum H086-0348: specified EA888 CCTA/CBFA, complete standard-bore kit. Nostrum claims 36% more flow and specifies 180 bar maximum operating pressure and a custom tune. Its catalogue lists 1.19 cc/rev geometric displacement with the stock cam.
  • Nostrum H086-0633: specified EA888 CCTA/CBFA, complete big-bore kit. Nostrum claims 63% more flow, specifies 240 bar maximum operating pressure and requires custom tuning; its catalogue lists 1.43 cc/rev geometric displacement with the stock cam. Neither maximum rating is an instruction to command that pressure on another system.
  • Nostrum H136-0570: selected EA888 rest-of-world applications; supplier states 33% more displacement, 1.43 cc/rev and a 200 bar maximum. Check original pump and exact engine compatibility; the product page specifies tuning.
  • Autotech 10-127-203K: selected EA888 Gen 3 MQB applications. Internal kit with an 11.66 mm piston. Autotech notes that some non-US 1.8 pumps and certain CPLA/CPPA sealed units do not accept this design.
  • APR Gen 3 Hitachi HPFP: selected EA888 Gen 3 applications with compatible Hitachi pumps. APR claims 37% more displacement and lists assembled or rebuild options.
  • Nostrum H136-0568: selected EA888 Gen 3 2.0T applications. Complete pump, claimed 36% greater flow and 200 bar maximum operating pressure; the supplier specifies tuning.

EA888 Evo4 high-pressure components and operating pressures differ from earlier examples. Do not assume a Gen 3 internal kit fits a Gen 4 pump: confirm the exact pump and hardware with the manufacturer. EcuTek's Evo4 guide describes a 35 MPa (350 bar) direct-injection system for its application.

Low-pressure pump examples

  • APR MS100078 FWD and MS100071 AWD: selected EA113 and EA888 Gen 1 applications. Auxiliary inline pump and controller retain the factory in-tank pump. APR's description states 255 L/h, but its specification table states 225 L/h; test conditions are not specified. Obtain clarification and check the documented tank/filter and drivetrain restrictions.
  • JDY dual-pump kit: specified EA113 Mk6 Golf R and related FWD/AWD variants. Supplier lists Walbro 450 or 525 pump options; its power claim depends on the complete fuel system, including supplemental injection where required.
  • Stratified Mk6 GTI pump assembly: EA888 Mk6 GTI example, with AEM 340 L/h or Hellcat 525 L/h pump options. The supplier recommends suitable tuning and offers controller options. Test pressure and voltage are not stated.
  • APR MS100123: selected EA888 Gen 3 factory-MPI applications. APR specifies a 305 L/h in-tank pump with factory PWM-controller integration, ethanol-compatible hardware and compatible software. Its nominal rating does not state pressure and voltage.
  • CTS Stage 3 CTS-FPK-004-450: selected Mk7/Mk7.5 EA888 Gen 3 MQB vehicles with the listed 5Q0919051BK/BM baskets. Uses a nominal Walbro 450 L/h E85-compatible pump; CTS specifies basket modification and software, and strongly recommends an upgraded controller.
  • CTS Stage 3.5: selected EA888 Gen 3 MQB applications with a nominal Walbro Hellcat 525 L/h pump. Check basket, controller and software requirements for the actual car.
  • Unitronic UH017-FLA: Mk8 GTI EA888 Evo4. Complete brushless pump and basket with controller and harness; Unitronic does not publish an L/h rating on the product page and specifies its compatible software.
  • RTMG 901-1644: selected EA888 Gen 4, including Mk8 Golf R and 8Y S3. Retains the OEM brushless pump and adds a staged Walbro 450 and controller. RTMG lists a 6.7 bar standard system configuration; that is not a specified test pressure for the pump's nominal 450 rating.

Using the comparison during a turbo upgrade

Check the turbo kit and tune supplier's fuel and hardware requirements for the exact version. Where supported, log low-side supply pressure, high-pressure request and actual, lambda target and measured lambda, engine speed, fuel composition and relevant faults under repeatable conditions. A larger LPFP cannot by itself correct an undersized HPFP or injector, and a high-pressure upgrade cannot compensate for inadequate tank supply. Injector flow, injection time, pressure control, wiring, controller capability and pump-basket refill also matter.

Establish a healthy mechanical baseline and confirm the appropriate ECU calibration before loading the engine. Fuel-system work, particularly direct injection, requires the vehicle-specific pressure-relief and installation procedure. Sources are supplier product descriptions and catalogues accessed 17 November 2026; capacities and compatibility must be checked with the relevant supplier for the actual configuration.

Turbo upgrade guides: See EA113 K03-to-K04 and turbo kits, EA888 Gen 1/2 K04 conversions, and EA888 Gen 3/Evo4 turbo upgrades for matched supplier packages and their specific fuelling requirements.

Related injector upgrades: A larger pump and larger injectors address different restrictions. Compare selected parts and their measurement conditions in the EA113 and EA888 injector upgrade comparison.

Revision 4: EA113 and EA888 fuel pump upgrade comparison

This comparison covers selected aftermarket high-pressure fuel pump (HPFP) and low-pressure fuel pump (LPFP) products for the 2.0 TFSI EA113 and 1.8/2.0 TSI/TFSI EA888. Fitments are supplier examples, not proof that a kit fits every engine in a family. Check the engine code, vehicle and market, original pump or basket, drivetrain, fuel, ECU software and current supplier instructions. Turbocharger power claims and pump capacity claims depend on the whole system and test conditions.

How to compare specifications

The HPFP supplies the direct-injection rail; the LPFP supplies it from the tank and can also feed port injection where fitted. An internal HPFP kit replaces components in a compatible existing pump; an assembled pump is a different purchase. An auxiliary LPFP can work alongside the existing in-tank pump, while other kits replace or modify the tank assembly. A high-pressure pump's larger geometric displacement can increase available volume without commanding higher rail pressure. APR describes the distinction for its Gen 3 pump.

Percentages below are the manufacturers' stated improvements against their own stock references; geometric displacement, measured flow and piston diameter are not interchangeable measures. LPFP litres-per-hour ratings depend on differential pressure, voltage, fuel and test method. Where the supplier does not state these conditions, the nominal figures are not directly comparable as installed flow.

High-pressure pump examples

  • Autotech 10-127-100K: EA113 early 2.0 TFSI, including the listed Mk5 GTI, Mk6 Golf R and 8P S3 examples. Internal kit, 9.8 mm piston; Autotech claims up to 50% more flow than its original-pump reference.
  • Integrated Engineering IEFUVC3: EA113 2.0 TFSI, including the listed Mk5 GTI and Mk6 Golf R. Complete new pump with upgraded internals; IE states 50% greater displacement and approximately 600 hp at 7,500 rpm with an appropriate setup. The power figure is a supplier claim, not a guaranteed limit for another engine or fuel.
  • APR MS100016: selected EA113 2.0 TFSI applications, including Mk5 GTI and Mk6 Golf R. Complete new pump; APR claims 41% greater displacement. The separately listed MS100017 rebuild uses the customer's pump.
  • Autotech 10-127-101K: specified longitudinal EA888 Gen 2 2.0T Audi applications. Internal kit with an 11.5 mm piston; the supplier's examples include 2009–14 B8 A4/A5/A6/Q5 and TT. Verify the fitted pump rather than assuming every Gen 1 or Gen 2 pump accepts the kit.
  • Nostrum H086-0348: specified EA888 CCTA/CBFA, complete standard-bore kit. Nostrum claims 36% more flow and specifies 180 bar maximum operating pressure and a custom tune. Its catalogue lists 1.19 cc/rev geometric displacement with the stock cam.
  • Nostrum H086-0633: specified EA888 CCTA/CBFA, complete big-bore kit. Nostrum claims 63% more flow, specifies 240 bar maximum operating pressure and requires custom tuning; its catalogue lists 1.43 cc/rev geometric displacement with the stock cam. Neither maximum rating is an instruction to command that pressure on another system.
  • Nostrum H136-0570: selected EA888 rest-of-world applications; supplier states 33% more displacement, 1.43 cc/rev and a 200 bar maximum. Check original pump and exact engine compatibility; the product page specifies tuning.
  • Autotech 10-127-203K: selected EA888 Gen 3 MQB applications. Internal kit with an 11.66 mm piston. Autotech notes that some non-US 1.8 pumps and certain CPLA/CPPA sealed units do not accept this design.
  • APR Gen 3 Hitachi HPFP: selected EA888 Gen 3 applications with compatible Hitachi pumps. APR claims 37% more displacement and lists assembled or rebuild options.
  • Nostrum H136-0568: selected EA888 Gen 3 2.0T applications. Complete pump, claimed 36% greater flow and 200 bar maximum operating pressure; the supplier specifies tuning.

EA888 Evo4 high-pressure components and operating pressures differ from earlier examples. Do not assume a Gen 3 internal kit fits a Gen 4 pump: confirm the exact pump and hardware with the manufacturer. EcuTek's Evo4 guide describes a 35 MPa (350 bar) direct-injection system for its application.

Low-pressure pump examples

  • APR MS100078 FWD and MS100071 AWD: selected EA113 and EA888 Gen 1 applications. Auxiliary inline pump and controller retain the factory in-tank pump. APR's description states 255 L/h, but its specification table states 225 L/h; test conditions are not specified. Obtain clarification and check the documented tank/filter and drivetrain restrictions.
  • JDY dual-pump kit: specified EA113 Mk6 Golf R and related FWD/AWD variants. Supplier lists Walbro 450 or 525 pump options; its power claim depends on the complete fuel system, including supplemental injection where required.
  • Stratified Mk6 GTI pump assembly: EA888 Mk6 GTI example, with AEM 340 L/h or Hellcat 525 L/h pump options. The supplier recommends suitable tuning and offers controller options. Test pressure and voltage are not stated.
  • APR MS100123: selected EA888 Gen 3 factory-MPI applications. APR specifies a 305 L/h in-tank pump with factory PWM-controller integration, ethanol-compatible hardware and compatible software. Its nominal rating does not state pressure and voltage.
  • CTS Stage 3 CTS-FPK-004-450: selected Mk7/Mk7.5 EA888 Gen 3 MQB vehicles with the listed 5Q0919051BK/BM baskets. Uses a nominal Walbro 450 L/h E85-compatible pump; CTS specifies basket modification and software, and strongly recommends an upgraded controller.
  • CTS Stage 3.5: selected EA888 Gen 3 MQB applications with a nominal Walbro Hellcat 525 L/h pump. Check basket, controller and software requirements for the actual car.
  • Unitronic UH017-FLA: Mk8 GTI EA888 Evo4. Complete brushless pump and basket with controller and harness; Unitronic does not publish an L/h rating on the product page and specifies its compatible software.
  • RTMG 901-1644: selected EA888 Gen 4, including Mk8 Golf R and 8Y S3. Retains the OEM brushless pump and adds a staged Walbro 450 and controller. RTMG lists a 6.7 bar standard system configuration; that is not a specified test pressure for the pump's nominal 450 rating.

Using the comparison during a turbo upgrade

Check the turbo kit and tune supplier's fuel and hardware requirements for the exact version. Where supported, log low-side supply pressure, high-pressure request and actual, lambda target and measured lambda, engine speed, fuel composition and relevant faults under repeatable conditions. A larger LPFP cannot by itself correct an undersized HPFP or injector, and a high-pressure upgrade cannot compensate for inadequate tank supply. Injector flow, injection time, pressure control, wiring, controller capability and pump-basket refill also matter.

Establish a healthy mechanical baseline and confirm the appropriate ECU calibration before loading the engine. Fuel-system work, particularly direct injection, requires the vehicle-specific pressure-relief and installation procedure. Sources are supplier product descriptions and catalogues accessed 17 November 2026; capacities and compatibility must be checked with the relevant supplier for the actual configuration.

Turbo upgrade guides: See EA113 K03-to-K04 and turbo kits, EA888 Gen 1/2 K04 conversions, and EA888 Gen 3/Evo4 turbo upgrades for matched supplier packages and their specific fuelling requirements.

Related injector upgrades: A larger pump and larger injectors address different restrictions. Compare selected parts and their measurement conditions in the EA113 and EA888 injector upgrade comparison.

Earlier 1.8T 20V: This page covers selected later direct-injection engines. The earlier port-injected 1.8T uses different fuelling hardware; see the 1.8T injector and fuel-pump guide for electric pump kits and module fitment.